Siemens ACVATIX G B111.9E/KN Series User manual

A6V10725318_en--_e Siemens
2018-06-05 Building Technologies
ACVATIX™
Rotary actuator for ball valves KNX / PL-Link
G..B111.9E/KN
Rotary actuator 5 / 10 Nm with KNX communication for 6-port control ball valves
and ball valves
●GDB111.9E/KN with 5 Nm nominal torque
●GLB111.9E/KN with 10 Nm nominal torque
●Operating voltage AC 24 V
●Supports KNX S-Mode and PL-Link
●For use with VWG41.. 6-port control ball valves and with 2-port and 3-port
ball valves up to DN 25 / DN 50
s

2 / 12
Siemens A6V10725318_en--_e
Building Technologies 2018-06-05
Features
Feature Description
Communication - KNX-TP, galvanically separated
- Max. 256 nodes per line (with repeaters)
- Busload 5 mA
Functions - Setpoint and actual value for actuator position 0..100%
- Operating mode “heating / cooling control” for 6-port control ball valve or
operating mode “position control” for 2-/3-port control ball valves
- Override control with binary communication objects
- Setpoint monitoring and backup mode
Type overview
Product no. Ordering no. Operating
voltage Control signal Power consumption Running time Manual override Position feedback
GDB111.9E/KN S55499-D203
AC 24 V KNX-TP 1 VA / 0.5 W
3 VA / 2.5 W 1) 150 s Yes Yes
GLB111.9E/KN S55499-D207
1) Actuator rotates
Ordering information (example)
Product no. Ordering no. Description Volume
GDB111.9E/KN S55499-D203 Rotary actuator KNX for 6-port ball valve or
control ball valves
1
Equipment combinations
6-port control ball valves PN16 GDB..9E..
Medium: 5…90 °C G..B kvs [m3/h] DN ∆pmax [kPa]
VWG41.10.. G ½ B 0.25 ..1.9 10 200
VWG41.20.. G 1 B 0.25 ..4.25 20 200

3 / 12
A6V10725318_en--_e Siemens
2018-06-05 Building Technologies
2- and 3-port control ball valves PN40 GDB..9E GLB..9E
internally threaded Rp externally threaded G..B kvs [m3/h] DN Χpmax ΧpsΧpmax Χps
2-port control ball valves
‒‒VAG61.15.. G 1 B 1…6.3 15
350 1400 - -
VAI61.15.. Rp ½“ ‒‒1…10 15
VAI61.20.. Rp ¾” VAG61.20.. G 1 ¼ B 4…10 20
VAI61.25.. Rp 1” VAG61.25.. G 1 ½ B 6.3…16 25
VAI61.32.. Rp 1¼” VAG61.32.. G 2 B 10…25 32
- - 350
1000
VAI61.40.. Rp 1½” VAG61.40.. G 2 ¼ B 16…40 40 800
VAI61.50.. Rp 2” VAG61.50.. G 2 ¾ B 25…63 50 600
3-port control ball valves
VBI61.15.. Rp ½“ VBG61.15.. G 1 B 1.6…6.3 15
350
-
-
-
VBI61.20.. Rp ¾” VBG61.20.. G 1 ¼ B 4…6.3 20
VBI61.25-10 Rp 1” VBG61.25-10 G 1 ½ B 10 25
VBI61.32-16 Rp 1¼” VBG61.32-16 G 2 B 16 32
-350
VBI61.40-25 Rp 1½” VBG61.40-25 G 2 ¼ B 25 40
‒‒VBG61.50-40 G 2 ¾ B 40 50
VBI61.50.. Rp 2” ‒‒40…63 50
Cf. section “product documentation” for datasheet numbers
Open/close 2-port and changeover ball valves 3-port PN 40 GDB..9E GLB..9E
internally
threaded Rp externally threaded G..B kvs [m3/h] DN Χpmax ΧpsΧpmax Χps
Open/close 2-port ball valves
‒‒VAI60.15-9 G 1 B 9 15
350 1400 - -
VAI60.15-15 Rp ½“ ‒‒15 15
‒ ‒ VAG60.20-17 G 1 ¼ B 17 20
VAI60.20-22 Rp 1” ‒ ‒ 22 20
VAI60.25-22 Rp 1” VAG60.25-22 G 1 ½ B 22 25
VAI60.32-35 Rp 1¼” VAG60.32-35 G 2 B 35 32
- - 350
1000
VAI60.40-68 Rp 1½” VAG60.40-68 G 2 ¼ B 68 40 800
VAI60.50-96 Rp 2” VAG60.50-96 G 2 ¾ B 96 50 600
Changeover ball valves 3-port
VBI60.15-5L Rp ½“ ‒‒515
350 - -VBI60.20-9L Rp 1” ‒‒920
VBI60.25-9L Rp 1” ‒‒925
VBI60.32-13L Rp 1¼” ‒‒13 32
- - 350 -
VBI60.40-25L Rp 1½” ‒‒25 40
VBI60.50-37L Rp 2” ‒‒37 50
‒‒VBG60.15-8T G 1 B 8 15
350 - - -
VBI60.15-12T Rp ½“ ‒‒12 15
‒ ‒ VBG60.20-13T G 1 ¼ B 13 20
VBI60.20-16T Rp 1” ‒ ‒ 16 20
‒ ‒ VBG60.25-13T G 1 ½ B 13 25
VBI60.25-16T Rp 1” ‒ ‒ 16 25
VBI60.32-25T Rp 1¼” VBG60.32-25T G 2 B 25 32
- - 350 -
VBI60.40-49T Rp 1½” VBG60.40-49T G 2 ¼ B 49 40
VBI60.50-73T Rp 2” VBG60.50-73T G 2 ¾ B 73 50
Cf. section “product documentation” for datasheet numbers

4 / 12
Siemens A6V10725318_en--_e
Building Technologies 2018-06-05
Controllers and room units Product no. Ordering no. Documentation
Room thermostat KNX RDG160KN S55770-T297 A6V10629627
(N3191)
Flush-mount room sensor KNX AQR2532NNW with
AQR2570NF or
AQR2576NF
S55720-S136
S55720-S203
S55720-S207
A6V10389050
(N1411)
Room control unit UP227/11 5WG1227-2AB11 A6V10387579
Software versions
G..B111.9E/KN series B are designed for using ETS device profile v2.x. ETS device profile
v1.x is supported for backward compatibility reasons.
Series information Series A Series B
Production period 12/2015 – 01/2017 01/2017
ETS device profile v1.x supported supported
ETS device profile v2.x not supported supported
Note: The Software-Tools ACS931 / 941 and the handheld tool AST20 are not supported by
the GDB111.9E/KN and GLB111.9E/KN.
Product documentation
Title Topic Document ID
Communication via the KNX bus Communication via the KNX bus A6V10075840 (P3127)
Mounting instruction Mounting instructions rotary actuator A6V10523083 (M4657)
or A6V10636144
Datasheet 6-port control ball valve Technical information on 6-port control ball valves
VWG41..
A6V10564480
Datasheet 2-port and 3-port control
ball valves, PN 40, with internally
threaded connection
Technical information on 2-port and 3-port control
ball valves VAI61… and VBI61..
N4211
Datasheet 2-port and 3-port control
ball valves, PN 40, with externally
threaded connection
Technical information on 2-port and 3-port control
ball valves VAG61… and VBG61..
N4212
Datasheet 2-port shutoff valves and
3-port changeover ball valves, PN
40, with internally threaded
connection
Technical information on 2-port shutoff and 3-port
changeover ball valves VAI60… and VBI60..
N4213
Datasheet 2-port shutoff valves and
3-port changeover ball valves, PN
40, with externally threaded
connection
Technical information on 2-port shutoff and 3-port
changeover ball valves VAG60… and VBG60..
N4114
How to obtain documentation and product-related software
Related documents such as environmental declarations, CE declarations, etc., can be down-
loaded at the following Internet address:
http://siemens.com/bt/download
The ETS device profile can be downloaded at the following Internet address:
http://siemens.com/hvac-td

5 / 12
A6V10725318_en--_e Siemens
2018-06-05 Building Technologies
HMI (Human-Machine Interface)
Push-button operation
Activity Push-button operation Confirmation
Enter / leave addressing mode Press button <1 s LED turns red or gets off
Reset to factory settings Press button >20 s LED flashes orange until device
restarts
PL-Link connection test 1) Press key >2 s and <20 s LED flashes 1x orange
1) Function or part of the function available in PL-Link operation only
LED colors and patterns
Color Pattern Description
Off --- Fault free operation or device not powered
Green steady Connection test successful 1)
Orange flashing a) Factory reset in progress
b) When a connection test was triggered: wait 1)
Red steady a) Device is in programming/addressing mode
b) When a connection test was triggered: Connection test failed 1)
1) Function or part of the function available in PL-Link operation only
Addressing and bus test with push button
The rotary actuators can be set into addressing/programming mode by push-button:
∂Press push button (<1 s)
∂KNX bus wiring OK ⇓LED turns red until addressing/programming is finished
∂KNX bus wiring not OK ⇓LED stays dark
Reset with push button
The rotary actuators can be reset by push-button:
∂Press push button >20 s
∂LED flashes orange
∂Device restarts
All parameters are reset to the default values.

6 / 12
Siemens A6V10725318_en--_e
Building Technologies 2018-06-05
Commissioning and parameterization
The following operating modes are available:
●Heating / cooling control: The actuator uses two separate setpoints for heating and cool-
ing each with a range 0...100%.
●Position control: The actuator is controlled with a 0...100% position setpoint.
Operating mode “Heating / cooling control”
When using “heating / cooling control” the parameters as listed below are available. Parame-
ter sets for 6-port control ball valves DN 10 and DN 20 can be selected. Details on the char-
acteristic curves of these two valves can be found in the datasheet A6V10564480.
Note that the valve angle [°] moves counter-clockwise, whereas the actuator position [%]
moves clockwise. Therefore valve angle 15° is achieved by an actuator position of 84% etc.
One of the two setpoints (heating or cooling) needs to be “0%” in order for the actuator to be
able to move. Are both setpoints not equal to “0%”, the actuator doesn’t move until the
setpoint conflict is resolved.
Valve angle and actuator position, example for VWG41.20
The 6 port control ball valve can
be mounted as shown in the
mounting instruction
A6V10636144 (coil facing
upward) or rotated by 180° (coil
facing downward). The ETS
parameter settings remain the
same, but heating and cooling
change their sides (cf. tables
below).
Parameters for standard piping of heating / cooling:
Parameter VWG41.10 VWG41.20
Valve angle Actuator position Valve angle Actuator position
Max. position heating 15° 84% 15° 84%
Min. position heating 30° 67% 40° 55%
Closed position 45° 50% 45° 50%
Min. position cooling 60° 33% 50° 45%
Max. position cooling 75° 16% 75° 16%
By parameter inversion, heating and cooling are swapped:
Parameter VWG41.10 VWG41.20
Valve angle Actuator position Valve angle Actuator position
Max. position heating 15° 16% 15° 16%
Min. position heating 30° 33% 40° 45%
Closed position 45° 50% 45° 50%
Min. position cooling 60° 67% 50° 55%
Max. position cooling 75° 84% 75° 84%

7 / 12
A6V10725318_en--_e Siemens
2018-06-05 Building Technologies
Operating mode “Position control”
Parameters available in “position control”:
Parameter Range Description Factory setting
Opening direction CW (R) / CCW (L) Opening direction of the actuator CW (R)
Max. position 0…100% Setting for the upper position limit 100%
Min. position 0…100% Setting for the lower position limit 0%
Parameterization of the KNX bus integration
The following parameters are usually checked and set by the systems integrator to achieve
the right level of bus traffic generated by the actuator or to define the behavior in case of
communication interruption. Parameters in the group “advanced” can be left unchanged
unless a special configuration is required.
Parameter group “Standard”:
Parameter Range Description Factory setting
Backup timeout 0…60 min
0 min = disabled
Time interval to detect communication interruption.
If disabled, the actuator controls to the last received
setpoint until a new setpoint is received.
30 min.
Backup mode Backup position
Keep last position
Actuator behavior when the communication timeout
has been exceeded (no setpoint received within the
defined time interval).
∂Backup position: Actuator drives to defined
position
∂Keep last position: Actuator keeps position
Backup position
Backup value 0…100% Position the actuator drives to in case of
communication interruption
50%
Parameter group “Advanced”:
Parameter Range Description Factory setting
Hysteresis (COV)
actuator position 1)
1...20% Threshold for the actuator position. COV below this
value are not sent over the bus
1%
Min. repetition time
actuator position
10...900 s Minimum waiting time until a COV above the
hysteresis threshold is sent over the bus
10 s
Override position 1 0…100% Position to which the actuator drives if the associated
group object is triggered (override priority)
0%
Override position 2 0…100% Position to which the actuator drives if the associated
group object is triggered (override priority)
100%
1) COV = Change of value

8 / 12
Siemens A6V10725318_en--_e
Building Technologies 2018-06-05
Notes
Safety
Caution
National safety regulations
Failure to comply with national safety regulations may result in personal injury and
property damage.
●Observe national provisions and comply with the appropriate safety regulations.
Mounting
Mounting positions
IP54 in the following mounting positions
Maintenance
The rotary actuators are maintenance-free.
Disconnect the electrical connections from the terminals if you want to work at the device.
Disposal
The device is considered electrical and electronic equipment for disposal in
terms of the applicable European Directive and may not be disposed of as do-
mestic garbage.
∂Dispose of the device through channels provided for this purpose.
∂Comply with all local and currently applicable laws and regulations.
Warranty
Technical data on specific applications are valid only together with Siemens products listed
under "Equipment combinations". Siemens rejects any and all warranties in the event that
third-party products are used.
Note
When using the actuators in connection with components of other manufacturers,
correct functioning must be ensured by the user, and Siemens will assume no
responsibility.

9 / 12
A6V10725318_en--_e Siemens
2018-06-05 Building Technologies
KNX Group Objects
Technical data
Power supply
Operating voltage G..B111.9E/KN AC 24 V ± 20% (SELV) or
AC 24 V class 2 (US)
Frequency 50/60 Hz
Power consumption at 50 Hz
Actuator holds 1 VA / 0.5 W
Actuator rotates 3 VA / 2.5 W
Function data
Positioning time for
nominal rotation angle
G..B111.9E/.. 150 s (50 Hz)
120 s (60 Hz)
Nominal torque GDB.. 5 Nm
Maximum torque GDB.. < 7 Nm
Nominal / maximum
rotation angle
90° / 95° ± 2°
Direction of rotation Adjustable over bus (operating mode
“position control”)
Clockwise (CW) /
Counter-clockwise (CCW)
Connection cables
Cable length 0.9 m
Power supply Number of cores and cross-sectional area 2 x 0.75 mm2
Communication Number of cores and cross-sectional area 2 x 0.75 mm2
Nr. Name in ETS Object
function Flags Data point type KNX Range
C R W T U ID DPT_Name Format Unit
1Fault information Transmit 1 1 0 1 0 219.001 _AlarmInfo 6 Byte --- [0...255 ] = Log Nr.
[0...2] = Alarm priority
[0...14] = Application area
[0...4] = Error class
[0...7] = Attributes
[0...7] = Alarm status
2Fault state Transmit 1 1 0 1 0 1.005 _Alarm 1 bit --- 0 = No alarm
1 = Alarm
3Fault transmission Receive 1 0 1 0 1 1.003 _Enable 1 bit --- 0 = Disable
1 = Enable
4Setpoint position /
Setpoint pos. heating 1) Receive 1 1 1 0 1 5.001 _Scaling 1 Byte % 0..100%
5Actual position /
Actual position heating 1)
Transmit 1 1 0 1 0 5.001 _Scaling 1 Byte % 0..100%
6Setpoint pos. cooling
1)
Receive 1 1 1 0 1 5.001 _Scaling 1 Byte % 0..100%
7Actual position cooling
1)
Transmit 1 1 0 1 0 5.001 _Scaling 1 Byte % 0..100%
8Fault Transmit 1 1 0 1 0 1.005 _Alarm 1 bit --- 0 = No alarm
1 = Alarm
9Override position 1 Receive 1 1 1 0 1 1.003 _Enable 1 bit --- 0 = Disable
1 = Enable
10 Override position 2 Receive 1 1 1 0 1 1.003 _Enable 1 bit --- 0 = Disable
1 = Enable
1) For operating mode “heating / cooling control”

10 / 12
Siemens A6V10725318_en--_e
Building Technologies 2018-06-05
Communication
Communication protocol Connection type KNX-TP (el. isolated)
Bus load 5 mA
Degree of protection
Degree of protection Degree of protection acc. to EN 60529
(see mounting instruction)
IP54
Safety class Safety class acc. to EN 60730 III
Environmental conditions
Applicable standard IEC 60721-3-x
Operation Climatic conditions Class 3K5
Mounting location Indoors
Temperature general 0…50 °C
Humidity (noncondensing) 5…95 % r. F.
Transport Climatic conditions Class 2K3
Temperature -25…70 °C
Humidity 5...95 % r. h.
Storage Climatic conditions Class 1K3
Temperature -5…45 °C
Humidity 5...95 % r. h.
Directives and Standards
Product standard EN 60730-x
Product family standard EN 50491-2, EN 50491-3, EN 50491-5
General requirements for Home and
Building Electronic Systems (HBES) and
Building Automation and Control
Systems (BACS)
Electromagnetic compatibility (Application) For residential, commercial and industrial
environments
EU Conformity (CE) A5W00003842 1)
RCM Conformity A5W00003843 1)
UL, cUL AC 24 V UL 873 http://ul.com/database
Environmental compatibility
The product environmental declaration A6V10209938 1) contains data on
environmentally compatible product design and assessments (RoHS compliance,
materials composition, packaging, environmental benefit, disposal).
Dimensions / Weight
Weight Without packaging 0.6 kg
Dimensions 71 x 158 x 61 mm
1) The documents can be downloaded from http://siemens.com/bt/download