Siemens BACnet User manual

Installation Instructions
Document No. 570-136
October 26, 2016
Smoke Control Listed BACnet Fume
Hood Controller
Item No. 570-136. Rev. CA Page 1 of 11
Generic Controller I/O Layout. See Wiring Diagram for application specific details.
Control Applications
6740, 6741 and 6742
Product Description
These instructions explain how to field install or
replace the Fume Hood Controller (FHC).
This BACnet Fume Hood Controls a Fast-acting
Damper or Venturi Air Valve to maintain control of a
chemical fume hood with up to 2 sashes. It uses
fast-acting electronic actuators (shipped separately)
to control the exhaust control device.
WARNING
The application cannot detect a
broken wire to the analog input
for the second sash.
An external sash aggregating
device should be used to
calculate the face area for all
fume hoods with more than one
sash.
This controller supports up to two Offboard AVS
signals. Offboard Air Module(s) (OAM) house AVS
transducers and send signals to the AVS input(s) on
the controller board. The controller can operate
stand-alone, with a field panel, or as part of a
network.

Document No. 570-136
Installation Instructions
October 26, 2016
Page 2 of 11 Siemens Industry, Inc.
Product Numbers
Fume Hood Controller
Applications 6740,6741,6742
This controller requires Offboard
Air Module(s) (ordered and
shipped separately
570-00701PKA
Offboard Air Module –two
required, order separately
550-819B
Operator Display Panel II (ODP II)
575-820A
Power Module
AQM2200
Siemens fast-acting Lab Electronic
Actuator(s) –order and ship
separately)
GNP191.1U
Shipping carton includes a controller assembly, a
mounting rail, and two self-tapping/drilling screws.
CAUTION
Keep the unit in its static-
proof bag until installation.
Otherwise you run the risk of
damage to the PCA from
electrostatic discharge.
ATTENTION
Ne pas retirer la carte de son
emballage avant son
installion.
Autrement, une décharge
électrostatique peut
endommager la carte
équipée.
Accessories
Room Sensor Cable 25 ft.
Room Sensor Cable 50 ft.
588-100A
588-100B
Vertical Sash Sensor
50 inch range
80 inch range
546-04000
546-04001
Parts for Smoke Control Compliance
Smoke Control Listed Large
Equipment Controller Enclosure
(Long board and ATEC
controllers).
550-002K
UL Listed Class 2 transformer with
120/240/277/480 Vac 50/60 HZ
0.5A primary with hub, and 24 Vac
96VA secondary w/ hub and circuit
breaker.
TR100VA004
NOTE:
For smoke control application, primary
rating is only 120V/60 Hz.
Warning/Caution Notation
WARNING
Personal injury/loss of life may
occur if you do not follow the
procedures as specified.
CAUTION
Equipment damage or loss of
data may occur if you do not
follow the procedures as
specified.
AVERTISSMENT
Risques de blessures graves
ou mortelles, si vous ne suivez
pas les procédures indiquées.
ATTENTION
Risques de dommages ou de
pertes de données, si vous ne
suivez pas les procédures
indiquées.

Document No. 570-136
Installation Instructions
October 26, 2016
Siemens Industry, Inc. Page 3 of 11
Required Tools and Equipment
Small flat blade screwdriver
3/8-inch open end wrench
Needle nose pliers
1/4-inch poly tubing
Prerequisites
Wiring conforms to NEC and local codes and
regulations. For further information see the
Wiring Guidelines Manual .
24 Vac Class II power available.
Supply power to the unit is OFF.
Any application specific hardware or devices
installed.
Fume Hood Controller Enclosure is mounted and
wiring has been roughed-in.
Operator Display Panel is installed and cable
pulled to location of controller.
Expected Installation Time
30 minutes
Installation Instructions
NOTE:
All wiring must conform to national and
local codes and regulations (NEC, CE,
etc.).
1. Secure the mounting rail in the controller’s
desired location.
2. Place the ESD wrist strap on your wrist and
attach it to a good earth ground.
3. Remove the controller from the static proof bag
and snap it into place on the mounting rail.
4. If the controller will be used with a field panel,
disconnect the field level network (FLN) trunk
from the field panel.
5. Wire the FLN trunk to the controller. After all
controllers are connected to the FLN, reconnect
the FLN trunk to the field panel.
6. If the controller requires Offboard Air Modules,
install them now following the appropriate
Installation Instructions (see Product Numbers ).
7. Connect the point wiring (see Wiring Diagram s).
CAUTION
DO Wiring –Each DO provides a
Normally Open (NO) terminal and a
Common (C) terminal.
To reduce noise and the potential
for ground loops, both connections
of a 24 Vac load must be wired
directly to the DO terminal on the
controller board.
8.
Plug the operator display cable into the ODP
port.
9.
Connect the power trunk. DO NOT apply
power to the controller without first consulting
the specialist.

Document No. 570-136
Installation Instructions
October 26, 2016
Page 4 of 11 Siemens Industry, Inc.
CAUTION
It is important that the neutral that
supplies the TEC must be earth
grounded at the source of the 24
Vac power.
Possible erratic equipment
operation or damage if neutral is not
grounded.
ATTENTION
Il est très important que le neutre
qui alimente le TEC soit mis à la
terre à la source de l’alimentation
24 Vca.
Risque de fonctionnement
incohérent de l’équipement ou de
dégats si le neutre n’est pas mis à
la terre.
10.
For a Fast Acting Lab Electronic Actuator,
verify that the switches are set as shown in
Figure Switch Settings for the Fast Acting
Lab Electronic Actuator .
Damper
Venturi Air Valve
Switch Settings for the Fast Acting Lab Electronic
Actuator.
The installation is complete.
Dimensions.
Smoke Control Compliance
The following instructions and information apply if
used for smoke control sequence.
1. Install Smoke Control Listed products, enclosure
and transformer. See the Product Numbers and
Accessories sections for more information.
2. Input Rating:
–24V 60 Hz 60 VA maximum
3. Digital Output (DO) are the only I/O authorized
for smoke control applications.
Digital Output (DO) Electrical Ratings:
–5 VA per DO/ maximum 40 VA total
4. The room temperature sensor (RTS) is installed
in the same area as the TEC.
5. Connection from the TEC to the field panel is a
maximum 4000 feet, 24 AWG minimum.
6. Wiring Range:
–Transformer: primary 14 AWG
–24 Vac Input Power: 14 to 18 AWG
–DO: AI: 18 to 20 AWG
–DI: 18 AWG
–LAN: 20 to 24 AWG
–RST: 24 AWG
All circuits are power limited; FLN is RS-485,
RTS is RS-232. Digital Inputs (DI) are dry
contacts.
See the following documents for more
information on configuring smoke control
applications:
 Smoke Control Systems Application and
Engineering Manual ( 125-1806)
 Smoke Control System Application Guide
( 125-1816)
 NFPA and UL Standards Relevant to Smoke
Control System Application Guide ( 125-
1817)

Document No. 570-136
Installation Instructions
October 26, 2016
Siemens Industry, Inc. Page 5 of 11
NOTE:
The 24 Vac relay module is not
applicable for smoke control
application.
Regulatory
FCC Statement Part 15.19
This Device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference,
and
2. This device must accept any interference
received, including interference that may cause
undesired operation
FCC Part 15.21, Information to user
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Part 15.105, Information to user
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Wiring Diagrams
Offboard Air Module Wiring.
CAUTION
The FHC-OAVS has two terminal
blocks with terminations numbered
identically (terminations 1 through
16). DO NOT get these mixed up
with each other.
If the FHC-OAVS is not connected
as shown, it is not resistant to
electrical surges. It is also
susceptible to interference from
other equipment.
ATTENTION
Le LCM-OAVS est muni de deux
bornes dont les contacts sont
numérotés à l’identique (contacts 1
à 16). NE PAS les confondre.
SI le LCM-OAVS n’est pas
connecté comme indiqué, il n’est
pas protégé contre les surtensions
électriques. Il est également
susceptible à des interférences
émises par d’autres périphériques.

Document No. 570-136
Installation Instructions
October 26, 2016
Page 6 of 11 Siemens Industry, Inc.
CAUTION
A separate power supply is required
if a 4-20 mA sensor is used.
Failure to follow wiring precautions
will result in equipment damage.
ATTENTION
Une alimentation séparée est
nécessaire, si un capteur 4…20
mA est utilisé.
Risque de dégâts matériels, si
les précautions de câblage ne
sont pas respectées.
Wiring for AI5: Sash Sensor 1.
Wiring for AI4: Sash Sensor 2.
WARNING
The application cannot detect a broken
wire to the analog input for the second
sash.
An external sash aggregating device
should be used to calculate the face
area for all fume hoods with more than
one sash.
AVERTISSMENT
L’application ne peut pas détecter un fil
rompu allant à une entrée analogique
pour le second châssis.
Un dispositif externe de cumulation de
châssis devrait être utilisé pour
calculer la surface à l’entrée de toutes
les hottes de laboratoire munies de
plus d’un châssis.
WARNING
Must use external 10 Vdc power
supply.
Do not power AI from an onboard AO
that is forced to 10 volts.
AVERTISSMENT
Doit utiliser une alimentation externe
de 10 V.
Ne pas alimenter un AI à partir d’un
AO forcé à 10 volts.
Wiring for AI with a 4 to 20 mA Sensor.

Document No. 570-136
Installation Instructions
October 26, 2016
Siemens Industry, Inc. Page 7 of 11
CAUTION
Each 4-20 mA sensor requires
a SEPARATE dedicated power
limited 24 VDC power supply.
DO NOT use the same
transformer to power both the
sensor and the controller.
ATTENTION
Chaque capteur 4-20 mA
nécessite un source
d’alimentation SÉPARÉE
limitée à 24 VDC.
NE PAS utiliser le même
transformateur pour alimenter le
capteur et le contrôleur.
NOTE:
If the voltage/current switch is set to
current and a 4 to 20 mA sensor is
connected to an AI, then special wiring
requirements must be followed.
NOTE:
When wiring any actuator that uses a 0 to
10V control signal and ties AC neutral to DC
common, an additional wire must connect
the actuator AC neutral to the DC common
of the PTEC/TEC AO being used to control
the actuator.
24 Vac Modulating Control.
Actuator
Symbol
TEC
Connection
Function
Terminal
Connection
Standard
Color
1
H
Supply (SP)
G
Red
2
C
Neutral (SN)
G0
Black
8
AO3 –15
(+)
0 to 10V
input signal
Y
Gray
--
C to AO3
16 (-)
Common
jumper
--
--
NOTE:
The controller’s DOs control 24 Vac
loads only. The maximum rating is 12 VA
for each DO. An external interposing
relay is required for any of the following:
• VA requirements higher than the
maximum
• 110 or 220 Vac requirements
• DC power requirements
• Separate transformers used to power
the load
(for example, part number 540-147,
Terminal Equipment Controller Relay
Module)

Document No. 570-136
Installation Instructions
October 26, 2016
Page 8 of 11 Siemens Industry, Inc.
Application 6740 Wiring Diagram.

Document No. 570-136
Installation Instructions
October 26, 2016
Siemens Industry, Inc. Page 9 of 11
Application 6741 Wiring Diagram.

Document No. 570-136
Installation Instructions
October 26, 2016
Page 10 of 11 Siemens Industry, Inc.
Application 6742 Wiring Diagram.