Siemens FDOOT241-9 User manual

007005_ad_en_-- Building Technologies
2019
-
01
-
22
Control Pr
oducts and Systems
Sinteso™ S
-
LINE
FDOOT241-9, FDOOT241-A, FDO241, FDT241
Automatic fire detectors
For the automatically addressed detector bus FDnet
●The ideal fire detector for every application
●Line separators for uninterrupted alarm function (FDOOT241-A, FDO241 and
FDT241)
●Signal processing with ASA
technology ™ (Advanced Signal Analysis)
●Event-controlled detection behavior
●Early and reliable detection when fires occur
●Highly developed immunity to deceptive phenomena
●FDO and FDOOT suitable for wind speeds of 1…20 m/s
●Prepared for future requirements thanks to its programmability

2
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Properties
Features
●Resistant to environmental and interfering influences such as dust, fibers, insects,
moisture, extreme temperatures, electromagnetic interference, corrosive vapors,
vibration, artificial aerosols, and atypical fire phenomena
●Shock resistant, theft protection as an accessory
●Time and process-dependent detection behavior
●Proven immunity to faults in power electronics
●Protected electronics, high-quality components
●Sophisticated sensors and electronic monitoring
●Internal alarm indicator (IAI), 360° visibility, alignment not necessary
●Integrated line separator
●'One-man' testing, commissioning, diagnostics, and maintenance
●Exchange the detector without resetting the parameters
●Exchange the detector without a ladder at heights up to 8 m
Ecological benefits
●Environmentally friendly processing
●Reusable materials
●Electronic parts and synthetic materials can be easily separated
●Environmentally friendly detector-testing without gas
Use
Multi-sensor fire detector FDOOT241-9
●Point detector with additional heat sensors
●Optional detector dust cap to protect the point detector during the
construction phase
Function
●Functions according to the scattered light principle with two sensors: Optical
forward and backward scattering
●Opto-electronic measuring chamber: Obstructs disruptive extraneous light
but can be relied upon to detect both light and dark smoke particles
●Two additional heat sensors increase the fire detector's immunity to
deceptive phenomena.
●Can be set as a multi-sensor smoke detector, smoke detector, or heat
detector by the software
●Selectable detection behavior thanks to application-specific ASA parameter
sets
●Multi-protocol: Collective / GMT (Cerberus / Siemens) / SynoLINE300,
FDnet
Use
●For early detection of flaming fires of solid and liquid substances as well as
of smoldering fires
●For early and reliable fire detection in an environment with deceptive
phenomena
●Can be used addressed, for the gradual modernization of:
Collective/GMT/SynoLINE300 on Sinteso FDnet ¹
¹ FS20 compatibility in FDnet is assured subject to in-country FS20 software support.

3
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Multi-sensor fire detector FDOOT241-A
●Point detector with additional heat sensors
●Optional detector dust cap to protect the point detector during the
construction phase
Function
●Functions according to the scattered light principle with two sensors: Optical
forward and backward scattering
●Opto-electronic measuring chamber: Obstructs disruptive extraneous light
but can be relied upon to detect both light and dark smoke particles
●Two additional heat sensors increase the fire detector's immunity to
deceptive phenomena.
●Can be set as a multi-sensor smoke detector, smoke detector, or heat
detector by the software
●Selectable detection behavior thanks to application-specific ASA parameter
sets
Use
●For early detection of flaming fires of solid and liquid substances as well as
of smoldering fires
●For early and reliable fire detection in an environment with deceptive
phenomena
●Can be used addressed
Smoke detector FDO241
●Optional detector dust cap to protect the point detector during the
construction phase
Function
●Functions according to the scattered light principle with one sensor: Optical
forward scattering
●Opto-electronic measuring chamber: Obstructs disruptive extraneous light
but can be relied upon to detect both light and dark smoke particles
●Selectable detection behavior thanks to application-specific ASA parameter
sets
Use
●For early detection of flaming fires as well as smoldering fires
●Can be used addressed
Heat detector FDT241
●Optional detector dust cap to protect the point detector during the
construction phase
Function
●Two heat sensors prevent the total failure of the thermal detection capacity
of in the event of a fault affecting a sensor.
●Measures the operating temperature and the temperature inside the
detector housing so that temperature rise can be detected.
●Selectable detection behavior thanks to application-specific ASA parameter
sets
Use
●For monitoring rooms in which rapid temperature rise is to be expected in
the event of a fire or if optical detection is difficult
●Can be used addressed

4
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Dummy detector FDX291
Use
●To cover bases that are left empty for prolonged periods of time
Type Overview
Type Designation Order no. Weight [kg]
Point detector
FDOOT241-9 Multi-sensor smoke detector A5Q00004813 0.106
FDOOT241-A Multi-sensor smoke detector S54310-F13-A1 0.106
FDO241 Smoke detector A5Q00004811 0.103
FDT241 Heat detector A5Q00004812 0.086
Base adapter
FDB241 Base adapter Sinteso (SIGMA/A+) S54319-F13-A1 0.086
FDB251 Base adapter Sinteso (Interactive) S54319-F28-A1 0.090
FDB281 Base adapter MS8/PMT A5Q00004929 0.125
FDB299 Base adapter Sinteso (AlgoRex coll.) S54319-F14-A1 0.086
Other accessories
FDUD290 Removal tool for adapter S54370-S13-A1 0.098
FDX291 Dummy detector S54319-F2-A1 0.120
FDOOT241-9M Migration kit A5Q00015955 0.140

5
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Accessories
You will find more information about detector bases and accessories in document 007775.
Addressable detector base FDB221 / FDB221-AA
Function:
●Detector base with stilts for fire detectors with addressable signal processing
●'Orange' connection terminals, 0.2…1.5 mm2conductor cross-section
●FDB221-AA also contains micro terminal DBZ1190-AA
Use:
●For recess-mounted cable entry
●For surface-mounted cable entry up to a cable diameter of 6 mm
Flat, addressable detector base FDB222
Function:
●Flat detector base for fire detectors with addressable signal processing
●'Orange' connection terminals, 0.2…1.5 mm2conductor cross-section
Use:
●For flush mounting; only for recess-mounted cable entry
Base attachment FDB291
Function:
●For routing surface-mounted cables larger than Ø 6 mm
●Detector base is secured with a snap fastener
Base attachment humid FDB293
●For achieving a higher protection category
●For mounting in wet or humid environments
●Required when using detector heating unit FDBH291
●Required when using protective cage DBZ1194 or EMC-protective cage
FDBZ294
●Mounted between detector base and ceiling
●Detector base mounted quickly: The detector base simply clicks into place in
base attachment humid FDB293.

6
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Base attachment wet FDB295
●Base attachment wet with additional integrated rubber seal for mounting in wet
or humid environments
●For achieving a higher protection category
●For mounting in wet or humid environments
●Required when using detector heating unit FDBH291
●Required when using protective cage DBZ1194
●Mounted between detector base and ceiling
●Detector base mounted quickly: The detector base simply clicks into place in
base attachment wet FDB295.
Sealing element FDBZ295
Function:
●For improving the protection category. However, detectors can no longer be
installed or removed using the detector exchanger.
Note: Cannot be used in conjunction with designation plate FDBZ291!

7
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Installation
Easy, time-saving, and completely reliable mounting
●Detector base FDB221 for surface-mounted and recess-mounted supply lines
●Detector base FDB222 for flush mounting, only for recess-mounted supply lines
●Extra-long mounting slits allow existing drill holes from other systems to be reused.
●A large opening in the detector base makes it easy to feed the cables through
●Screwless connection terminals (spring clip principle)
●Detector line can be connected without any tools. The wire can be inserted easily by
hand.
●The detector can be mounted in the base easily by hand or using a detector exchanger
●The alarm indicator (AI) is centered in the detector, which means there is no need to
align the detector
1
2
3
4
5
1 Mounting slit 4 Alarm indicator
2 Screwless connection terminals 5 Opening for cable entry
3 Detector base
You will find more information in document 007775.
Disposal
The device is considered an electronic device for disposal in accordance
with the European Guidelines and may not be disposed of as domestic
garbage.
●Dispose of the device through channels provided for this purpose.
●Comply with all local and currently applicable laws and regulations.
●Dispose of empty batteries in designated collection points.

8
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Technical data
FDOOT241-9 FDOOT241-A FDO241 FDT241
Operating voltage (modulated) DC 12…33 V
Operating current (quiescent) 65…230 μA 180…230 μA 130…200 μA
External alarm
indicators (EAI)
which can be
connected
Without sounder
base
2
With sounder
base
1
Communication protocol FD20 or collective FDnet
System compatibility
FS20¹, AlgoRex, SIGMASYS
CZ10, CS11,
BC10, FC10,
XC10, FC330A,
FC700A, BMS,
SM80/88D100
–
Operating temperature -25…+70 °C -35…+70 °C -25…+70 °C -25…+50 °C /
-25…+65 °C /
Depending on parameter settings
Storage temperature -30…+75 °C -35…+75 °C -30…+75 °C
Air humidity ≤95 % rel.
Color ~RAL 9010 pure white
Protection
category
(IEC 60529)
With detector
base FDB221/-
AA, FDB222,
FDB291
IP43
Base FDB221
and sealing
element
FDBZ295 IP44
Base attachment
humid FDB293
or base
attachment wet
FDB295
Standards
CEA 4021, EN 54-5 – EN 54-5
EN 54-17
EN 54-7 –
– EN 54-27 – –
Approvals:
●VdS
●LPCB
●FM
●DNV GL (Marine)
G204007
126bh/01
3029351
–
G215052
–
–
–
G204017
126bf/02
3029351
MEDB00003UK
G204019
126bj/02
3046115
MEDB00003UR
Permissible wind speed 1…20 m/s –
¹ FS20 compatibility in FDnet is assured subject to in-country FS20 software support.

9
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Dimensional drawing
5
4
.
6
4
5
.
7
100
4
5
.
7
100
With base FDB221 for surface-mounted cable
entry
With base FDB222 for flush mounting
Product documentation
Document ID Title
007004 Technical manual Automatic fire detectors FDOOT221, FDOOT241-A3, FDOOT241-
A4, FDOOT241-A5, FDOOT241-8, FDOOT241-9, FDOOT241-A9, FDO241, FDO221,
FDT241, FDT221
007775 Data Sheet Detector bases and accessories FDB22x, FDB20x, FDB241, FDB251,
FDB281, FDB299
008164 Equipment overview Sinteso™ Detector system FD20
008331 List of compatibility (for 'Sinteso™' product line)
009409 Data sheet Colored detectors, bases and base attachment FDO.., FDOOT…, FDT…,
FDB…, FDCW241
Related documents such as the environmental declarations, CE declarations, etc., can be
downloaded from the following Internet address:
https://siemens.com/bt/download

10
Building Technologies
007005_ad_en_
--
Fire Safety 2019-01-22
Issued by
Siemens Switzerland Ltd
Building Technologies Division
International Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. [phone]
www.siemens.com/buildingtechnologies
© Siemens Switzerland Ltd, 2014
Technical specifications and availability subject to change without notice.
Document ID 007005_ad_en_-- FD20
Edition 2019-01-22
0786
Siemens Schweiz AG, Theilerstrasse 1a
CH-6300 Zug
Technical data: see doc. 007004
The declared performance and conformity can be seen in the Declaration of Performance (DoP) and the EU Declaration of Conformity (DoC),
which is obtainable via the Customer Support center: Tel. [phone] or https://siemens.com/bt/download
07
FDOOT241-9 - Smoke/heat detector incl. short-circuit isolator for use in fire detection and fire alarm systems installed in buildings.
305/2011/EU (CPR): EN 54-5 / EN 54-7 / EN 54-17; 2014/30/EU (EMC): EN 50130-4 / EN 61000-6-3 ; 2011/65/EU (RoHS): EN 50581
DoP No.: 0786-CPR-20007; DoC No.: CED-FDOOT241-9
FDOOT241-9
0786
Siemens Schweiz AG, Theilerstrasse 1a
CH-6300 Zug
Technical data: see doc. 007004
The declared performance and conformity can be seen in the Declaration of Performance (DoP) and the EU Declaration of Conformity (DoC),
which is obtainable via the Customer Support center: Tel. [phone] or https://siemens.com/bt/download
15
FDOOT241-A - Smoke/heat detector for use in fire detection and fire alarm systems installed in buildings.
305/2011/EU (CPR): EN 54-5 / EN 54-7 / EN 54-17; 2014/30/EU (EMC): EN 50130-4 / EN 61000-6-3 ; 2011/65/EU (RoHS): EN 50581
DoP No.: 0786-CPR-21451; DoC No.: CED-FDOOT241-A
FDOOT241-A
Siemens Schweiz AG; Theilerstrasse 1a
CH-6300 Zug
Technical data: see doc. 007004
07
FDO241 - Point type smoke detector incl. short-circuit isolator for use in fire detection and fire alarm systems installed in buildings.
305/2011/EU (CPR): EN 54-7 / EN 54-17 ; 2014/30/EU (EMC): EN 50130-4 / EN 61000-6-3 ; 2011/65/EU (RoHS): EN 50581
The declared performance and conformity can be seen in the Declaration of Performance (DoP) and the EU Declaration of Conformity (DoC), which is
obtainable via the Customer Support Center: Tel. [phone] or https://siemens.com/bt/download
DoP No.: 0786-CPR-20002; DoC No.: CED-FDO241
0786 FDO241
Siemens Schweiz AG; Theilerstrasse 1a
CH-6300 Zug
Technical data: see doc. 007004
07
FDT241 - Point type heat detector incl. short-circuit isolator for use in fire detection and fire alarm systems installed in buildings.
305/2011/EU (CPR): EN 54-5 / EN 54-17 ; 2014/30/EU (EMC): EN 50130-4 / EN 61000-6-3 ; 2011/65/EU (RoHS): EN 50581
The declared performance and conformity can be seen in the Declaration of Performance (DoP) and the EU Declaration of Conformity (DoC), which is
obtainable via the Customer Support Center: Tel. [phone] or https://siemens.com/bt/download
DoP No.: 0786-CPR-20004; DoC No.: CED-FDT241
0786 FDT241