Siemens SIMATIC RF360R Instruction sheet

SIMATIC RF360R
SIMATIC Ident
RFID systems
SIMATIC RF360R
Configuration Manual
03/2022
C79000
-G8976-C629-02
Introduction
1
Security recommendations
2
Description
3
Commissioning
4
Configuring
5
Configuring with the WBM
6
Programming
7
Service and maintenance
8
Syslog messages
A
Service & Support
B

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C629-02
Ⓟ
01/2022 Subject to change
Copyright © Siemens AG 2021 - 2022.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 3
Table of contents
1 Introduction ........................................................................................................................................... 5
2 Security recommendations.................................................................................................................... 7
2.1 Protocols ........................................................................................................................... 10
2.2 Security information .......................................................................................................... 12
3 Description........................................................................................................................................... 13
3.1 Properties of the reader ..................................................................................................... 13
3.2 User-specific procedure...................................................................................................... 15
4 Commissioning .................................................................................................................................... 17
4.1 Important notes on using the device .................................................................................. 17
4.2 Connect the hardware ....................................................................................................... 18
4.3 Network topology.............................................................................................................. 20
5 Configuring.......................................................................................................................................... 23
5.1 Assigning the IP address / device name............................................................................... 23
5.1.1 Assigning the IP address / device name with STEP 7 ............................................................ 23
5.1.2 Assigning the IP address / device name with SINEC PNI ....................................................... 26
5.1.3 Assigning an IP address via DHCP ....................................................................................... 27
5.2 Configuration via PROFINET IO (STEP 7).............................................................................. 28
5.3 Configuration via XML ....................................................................................................... 32
5.4 Configuration via OPC UA................................................................................................... 32
5.5 Configuring with Studio 5000 Logix Designer..................................................................... 32
6 Configuring with the WBM .................................................................................................................. 33
6.1 Starting WBM..................................................................................................................... 33
6.2 The WBM ........................................................................................................................... 36
6.3 The menu items of the WBM .............................................................................................. 40
6.3.1 The "Start page" menu item ............................................................................................... 40
6.3.2 The "Settings - General" menu item .................................................................................... 42
6.3.3 The "Settings - Reader Interface" menu item ....................................................................... 44
6.3.4 The "Settings - Communication" menu item........................................................................ 46
6.3.5 The menu command "Diagnostics - Hardware diagnostics".................................................. 56
6.3.6 The "Diagnostics - Log" menu item ..................................................................................... 60
6.3.7 The "Diagnostics - Service Log" menu item.......................................................................... 62
6.3.8 The "Diagnostics - Syslog logbook" menu item.................................................................... 63
6.3.9 The "Edit transponder" menu item...................................................................................... 64
6.3.10 The "User management" menu item................................................................................... 65
6.3.11 The "Homepage" menu item .............................................................................................. 68

Table of contents
SIMATIC RF360R
4Configuration Manual, 03/2022, C79000-G8976-C629-02
6.3.12 The "System - Device settings" menu item .......................................................................... 71
6.3.13 The "Help" menu item ........................................................................................................ 72
7 Programming....................................................................................................................................... 73
7.1 Programming via SIMATIC controller .................................................................................. 73
7.2 Programming via XML........................................................................................................ 73
7.3 Programming via OPC UA................................................................................................... 73
7.4 Programming via Rockwell controller ................................................................................. 74
8 Service and maintenance .................................................................................................................... 75
8.1 Diagnostics........................................................................................................................ 75
8.1.1 Diagnostics via the LED display........................................................................................... 76
8.1.2 Diagnostics via SNMP......................................................................................................... 78
8.1.3 Diagnostics using the WBM ................................................................................................ 79
8.1.4 Diagnostics using the TIA Portal (STEP 7 Basic / Professional) .............................................. 79
8.1.5 Diagnostics via XML........................................................................................................... 81
8.1.6 Diagnostics over OPC UA.................................................................................................... 81
8.1.7 Diagnostics using Studio 5000 Logix Designer.................................................................... 81
8.1.8 Parameterization of the diagnostics ................................................................................... 82
8.2 Error messages .................................................................................................................. 83
8.2.1 Error messages of the reader.............................................................................................. 83
8.2.2 Reading out error messages using the WBM ....................................................................... 90
8.2.3 XML error messages........................................................................................................... 91
8.2.4 OPC UA error messages...................................................................................................... 91
8.3 Firmware update ............................................................................................................... 94
8.3.1 Updating the firmware via WBM......................................................................................... 94
8.3.2 Update firmware via TIA Portal (STEP 7 Basic / Professional)................................................ 95
8.4 Factory settings ................................................................................................................. 96
8.4.1 Restoring the factory settings via WBM............................................................................... 96
8.4.2 Reset the factory setting with SINEC PNI............................................................................. 97
8.4.3 Restoring the factory settings via the XML.......................................................................... 97
8.4.4 Restoring the factory settings for the hardware .................................................................. 98
8.5 Module replacement.......................................................................................................... 99
8.5.1 Backup configuration data ............................................................................................... 100
8.5.2 Replacing a module ......................................................................................................... 101
A Syslog messages................................................................................................................................ 103
A.1 Structure of the Syslog messages ..................................................................................... 103
A.2 Variables in Syslog messages ........................................................................................... 104
A.3 List of Syslog messages.................................................................................................... 105
B Service & Support .............................................................................................................................. 109

SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 5
Introduction
1
Purpose of these operating instructions
This manual contains all the information required for the commissioning and parameter
assignment of the SIMATIC RF360R readers.
This manual is intended for:
•Commissioning engineers
•Configuration engineers
•Service technicians
Basic knowledge required
These operating instructions assume general knowledge of automation engineering and
identification systems.
Scope of validity of this documentation
This documentation is valid for all delivery variants of the SIMATIC RF360R reader as of
product version "01" and delivery date as of 03/2022 as well as firmware version V2.0.
Trademarks
The following and possibly other names not identified by the registered trademark sign ® are
registered trademarks of Siemens AG:
SIMATIC ®, SIMATIC RF ® and MOBY ®
Orientation in the documentation
You can find information on the properties, technical specifications and application options
of the SIMATIC RF360R reader in the "SIMATIC RF300" system manual.
In addition to these operating instructions, you require the operating instructions for the S7-
300, S7-400, S7-1200 or S7-1500 controller used. When using an S7 controller, you can find
information on programming the module and a complete error description in the description
of the "Ident profile and Ident blocks" function blocks, the RFID standard profile and the
FB 45.
You can find all relevant information for XML configuration and programming in the "XML
Programming for SIMATIC Ident" manual. You can find detailed information on configuring
and programming over OPC UA in the "OPC UA for SIMATIC Ident" manual. You can find the
information on configuring and programming over EtherNet/IP in the "Ident profile, Add-on
instruction for Rockwell systems" manual.
You can find the current versions of the various manuals on the pages of the Siemens
Industry Online Support (https://support.industry.siemens.com/cs/ww/en/ps/14970/man).

Introduction
SIMATIC RF360R
6Configuration Manual, 03/2022, C79000-G8976-C629-02
Abbreviations and naming conventions
The following terms/abbreviations are used synonymously in this document:
Transponder, tag
Data medium, mobile data storage (MDS)
Communication module (CM)
Interface module (ASM)

SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 7
Security recommendations
2
To prevent unauthorized access, observe the following security recommendations when
working with the reader and WBM (Web Based Management).
General
•Check regularly that the device complies with these recommendations and/or other
internal security policies.
•Evaluate your plant as a whole in terms of security. Use a cell protection concept with
suitable products.
•Do not connect the device directly to the Internet. Operate the device within a protected
network area.
Physical access
•Restrict physical access to the device.
•Make sure that only adequately qualified personnel have access to the device.
•Lock unused physical ports (e.g. Ethernet ports) on the device. Unused ports can be used
to access the system without authorization.
•The devices have "Low-level service access" that can only be enabled via additional
hardware interconnection. The access is used to enable Siemens personnel to perform
advanced examination for servicing. The access may only be used by qualified service
personnel. Any other use results in the loss of the warranty.
Software (security functions)
•Keep the software up to date. Keep yourself informed regularly about safety updates for
the product.
You can find information about this at Link: (https://www.siemens.com/industrialsecurity).
•Activate only protocols that you actually need to use the device. Note that, in the factory
setting, all protocols can be used. However, while the device has established a connection
via a protocol, all other protocols are disabled.
•Disable EtherNet/IP-CIP if you do not need it. Only enable EtherNet/IP-CIP if you require a
connection to EtherNet/IP-CIP.
•The XML protocols are sent unencrypted. Take suitable measures to ensure that the XML
communication is tap-proof.
•Limit access to the device using an external device through a firewall or rules in an access
control list (ACL). The firewall and access list can only be configured via an external
device.

Security recommendations
SIMATIC RF360R
8Configuration Manual, 03/2022, C79000-G8976-C629-02
•The configuration files are available in XML format for simple use. Make sure that the
configuration files outside the device are suitably protected. You can, for example, encrypt
the files, store them at a safe location and transfer them only via secure communication
channels.
•The device provides options for backing up and restoring the configuration. For security
reasons, neither the IP address of the network interface nor data of the local user
administration are backed up. We recommend that you use the network management
system "SINEC NMS" to manage this data.
Passwords
•Always use the user management and create new user profiles.
•Change all default passwords for users before operating the device.
•Only use passwords with high password strength. Avoid weak passwords, e.g. password1,
123456789, abcdefgh.
•Define rules for using devices and assigning passwords.
•Make sure that all passwords are protected and inaccessible to unauthorized personnel.
•Do not use the same password for different users and systems.
•Update passwords and keys regularly to improve security.
Keys and certificates
This section deals with the security keys and certificates that you need to set up SSL.
•We urgently recommend creating your own SSL certificates and making them available.
Preset certificates and keys are present in the device.
The preset and automatically created SSL certificates are self-signed. We recommend
using certificates signed either by a reliable external certification authority or an internal
certification authority.
The device has an interface via which you can import certificates and keys.
•We recommend that you use certificates with a cryptographic key length of at least 4096
bits.
•If protocols support both certificates and keys, you should favor certificates.
•With operation via OPC UA, always use the "Sign and encrypt" security method.

Security recommendations
SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 9
•The following certificate formats are supported for the import:
Certificate
Supported formats
HTTPS
OPC UA server
*.p12
*.pfx
*.pem 1)
*.cer
*.cert
*.der
OPC UA client
OPC UA CA
OPC UA issuer
*.pem 1)
*.cer
*.cert
*.der
1)
May contain a private key.
•The following algorithms are supported for encryption:
Protocol Supported
signature algorithms
Supported key
and size
Web browser
SHA1
SHA256 with RSA
SHA384 with RSA
SHA512 with RSA
RSA 2048 bit
RSA 4096 bit
OPC UA
SHA256 with RSA
SHA384 with RSA
SHA512 with RSA
RSA 2048 bit
RSA 4096 bit
•The following cipher suites are supported for HTTPS:
OpenSSL name
Value
Browser
ECDHE-RSA-AES128-GCM-SHA256
0x2F
Chrome, Firefox
ECDHE-RSA-AES256-GCM-SHA384
0x30
Chrome, Firefox
Firmware encryption
The firmware itself is signed and encrypted. This ensures that only authentic firmware can be
downloaded to the device.

Security recommendations
2.1 Protocols
SIMATIC RF360R
10 Configuration Manual, 03/2022, C79000-G8976-C629-02
2.1 Protocols
Secure/non-secure protocols
•SNMPv1 is enabled in the factory setting in order to facilitate operation of the device in a
PROFINET environment. Check whether it is necessary to use SNMPv1. SNMPv1 is
classified as non-secure. Make use of the possibility to prevent write access. The product
offers corresponding settings for this.
•If SNMP is activated, change the community names. If no unrestricted access is necessary,
restrict access over SNMP.
•Use only secure protocols when access to the device is not secured by physical protection
measures.
The following protocols provide secure alternatives:
HTTP → HTTPS
•To prevent unauthorized access to the device or network, set up appropriate safeguards
against non-secure protocols.
•Enable only the services (protocols) that will actually be used on the device. The same
applies to the installed interfaces/ports. Unused ports could be used to access the network
downstream from the device.
•When using OPC UA, only use profiles with secure encryption and authentication.

Security recommendations
2.1 Protocols
SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 11
List of available protocols
All available protocols and their ports that are used with SIMATIC RF360R are listed below.
Table 2- 1 List of available protocols
Service/
Protocol
Protocol/
Port number
Preset port
status
Port
configurable
Port number
configurable
Authenticatio
n
Encryption
DHCP
UDP/68
Open
✓
--
--
--
PROFINET
UDP/34964
UDP/49152-
65535
Open
✓
--
--
--
HTTP
TCP/80
Closed
✓
--
--
--
HTTPS
TCP/443
Open
✓
--
✓
✓
NTP
UDP/123
Closed
✓
--
--
--
SNMP
UDP/161
Open
✓
--
--
--
EtherNet/IP
TCP/44818
UDP/44818
UDP/2222
Open
✓
--
--
--
OPC UA
TCP/4840
Open
✓
✓
✓(when
configured)
✓(when
configured)
XML
TCP/10001
Open
1)
✓
✓
--
--
Syslog
UDP/49152-
65535
Closed
✓
2)
--
--
--
1)
Applies to protocol number 10001, all others are closed.
2) Only outgoing, when configured.
Explanation of the table:
•Authentication
Specifies whether authentication of the communication partner takes place.
•Encryption
Specifies whether the transfer is encrypted.

Security recommendations
2.2 Security information
SIMATIC RF360R
12 Configuration Manual, 03/2022, C79000-G8976-C629-02
2.2 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customer’s exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity.
Note on firmware/software support
Siemens only provides bug and security fixes for the last released firmware/software version.
This means that Siemens only monitors the current firmware/software version for security
vulnerabilities.

SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 13
Description
3
3.1 Properties of the reader
Area of application
The SIMATIC RF360R reader was specially designed for use in industrial production for the
control and optimization of material flow within an area with protected access. The reader is
characterized by a high data transfer rate. The reader can process transponders of the ISO
15693 and RF300 (proprietary) standards.
Compared to other readers of the SIMATIC RF300 product family - which usually have an RS-
422 interface for communication with higher-level communication modules - the RF360R has
two PROFINET IO interfaces. Due to this special feature, the reader can be operated both on
the field level via a direct connection to an S7 controller and via a PC or on the IT level. This
means diagnostic data, such as processed transponder data or log entries, can be transferred
to higher-level systems via OPC UA or XML parallel to regular operation. In addition,
PROFINET IO can be looped on to another module.
Figure 3-1 Reader SIMATIC RF360R
In addition to the familiar configuration types via TIA Portal and GSDML, this reader also
feature integrated Web Based Management (WBM), which enables devices to be set via a
standard browser. The WBM supports you during commissioning, diagnostics and servicing. It
also enables the reading/writing of transponder data.
For security reasons, you should only operate the device within a protected network area and
not connect it directly to the Internet.

Description
3.1 Properties of the reader
SIMATIC RF360R
14 Configuration Manual, 03/2022, C79000-G8976-C629-02
You can find additional information on the various RFID devices and optical readers on the
Internet on the "Siemens Industry Online Support
(https://support.industry.siemens.com/cs/ww/en/ps/14970/man)" page.
Features
The following features characterize the RF360R reader:
Table 3- 1 Features the reader
Features
RF360R
Ethernet interfaces
2x M12, switch integrated
Transmission speed: 100 Mbps
Degree of protection
IP67
Configuration/
diagnostic options
STEP 7 (TIA Portal), GSDML, WBM (Web browser)
Application protocols
PROFINET IO, EtherNet/IP, OPC UA, XML
Function blocks
Ident profile, faceplates for PCS 7
Supported SIMATIC
controllers
S7-300, S7-400, S7-1200, S7-1500
Supported third-party
controllers
Source code of the Ident profile available. All controllers with
PROFINET and IEC61131 programming are supported.
Readable transponder
standards
ISO 15693
RF300 (proprietary)
NOTICE
IRT is not supported
Note that the reader does not support IRT (Isochronous Real Time). Neither can the reader
function as an IRT conductor (e.g. in a bus structure).
The reader can be configured as a client in MRP rings. Network diagnostics via SNMP is
supported by the reader.
NOTICE
Operation in VLANs
Note that the reader cannot be operated in VLANs whose ID is ≠ 0.

Description
3.2 User-specific procedure
SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 15
3.2 User-specific procedure
The reader of the SIMATIC RF360R is pre-configured ex works and can immediately be put
into operation. The reader obtains its IP address via a DHCP server at the factory.
As described above, the reader is designed for different environments and requirements.
If you operate the reader in an automation environment, they are configured and
programmed from the perspective of an S7 user. Integration in third-party controllers (e.g.
Rockwell controllers) is, of course, also possible. In this case, the configuration, engineering,
and programming is performed from the point of view of a Rockwell user. If you operate the
reader in an XML environment, it is configured and programmed from the perspective of an
XML user. If you operate the reader in an OPC UA environment, they are configured and
programmed from the perspective of an OPC UA user.
If you want to adapt the reader to your requirements, we recommend the following user-
specific procedure:
Procedure as S7 user
1. Connect the hardware
You can find information on this in the section "Connect the hardware (Page 18)".
2. Assign the IP address / device name
You can find information on this in the section "Assigning the IP address / device name
with SINEC PNI (Page 26)" or "Assigning the IP address / device name with STEP 7
(Page 23)".
3. Configure reader and if applicable communications module
You will find information on this in the section "Configuration via PROFINET IO (STEP 7)
(Page 28)" or "Configuring with the WBM (Page 33)".
4. Configure / program the reader commands
You can find information on this in the section "Programming via SIMATIC controller
(Page 73)".
Procedure as XML user
1. Connect the hardware
You can find information on this in the section "Connect the hardware (Page 18)".
2. Assign the IP address / device name
You can find information on this in the section "Assigning the IP address / device name
with SINEC PNI (Page 26)".
3. Configuring the reader
You can find information on this in the section "Configuration via XML (Page 32)" or
"Configuring with the WBM (Page 33)".
4. Program reader commands
You can find information on this in the section "Programming via XML (Page 73)".

Description
3.2 User-specific procedure
SIMATIC RF360R
16 Configuration Manual, 03/2022, C79000-G8976-C629-02
Procedure as an OPC UA user
1. Connect the hardware
You can find information on this in the section "Connect the hardware (Page 18)".
2. Assign the IP address / device name
You can find information on this in the section "Assigning the IP address / device name
with SINEC PNI (Page 26)".
3. Configuring the reader
You can find information on this in the section "Configuration via OPC UA (Page 32)" or
"Configuring with the WBM (Page 33)".
4. Program reader commands
You can find information on this in the section "Programming via OPC UA (Page 73)".
Procedure as Rockwell user
1. Connect the hardware
You can find information on this in the section "Connect the hardware (Page 18)".
2. Assign the IP address / device name
You can find information on this in the section "Assigning the IP address / device name
with SINEC PNI (Page 26)" or "Assigning an IP address via DHCP (Page 27)".
3. Configuring the reader
You can find information on this in the sections "Configuring with Studio 5000 Logix
Designer (Page 32)" and "Configuring with the WBM (Page 33)".
4. Configure / program the reader commands
You can find information on this in the section "Programming via Rockwell controller
(Page 74)".
Orientation in the document
Later in the document, these symbols will help your orientation and will show you whether
the section is of interest to you or not. Only the sections with user-specific content, in other
words, content that is interface-specific, contain these symbols. Sections without these
symbols are general and relevant for all areas of application.

SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 17
Commissioning
4
4.1 Important notes on using the device
Safety notices on the use of the device
The following safety notices must be adhered to when setting up and operating the device
and during all work relating to it such as installation, connecting up, replacing devices or
opening the device.
General notes
WARNING
Safety extra low voltage
The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a Limited
Power Source (LPS). (This does not apply to 100 V ... 240 V devices.)
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1
must be connected to the power supply terminals. The power supply unit for the equipment
power supply must comply with NEC Class 2, as described by the National Electrical Code (r)
(ANSI / NFPA 70).
There is an additional requirement if devices are operated with a redundant power
supply:
If the equipment is connected to a redundant power supply (two separate power supplies),
both must meet these requirements.
NOTICE
Alterations not permitted
Alterations to the devices are not permitted. If this is not adhered to, the radio approvals,
the relevant country approvals (e.g. CE or FCC) and the manufacturer's guarantee are
invalidated.

Commissioning
4.2 Connect the hardware
SIMATIC RF360R
18 Configuration Manual, 03/2022, C79000-G8976-C629-02
Overvoltage protection
NOTICE
Protection of the external 24 VDC voltage supply
If the module is supplied via extensive 24 V supply lines or networks, interference by strong
electromagnetic pulses on the supply lines is possible, e.g. from lightning or the switching
of large loads.
The connector for the 24 VDC external power supply is not protected against strong
electromagnetic pulses. Make sure that any cables liable to lightning strikes are fitted with
suitable overvoltage protection.
Repairs
WARNING
Repairs only by authorized qualified personnel
Repairs may only be carried out by authorized qualified personnel. Unauthorized opening of
and improper repairs to the device may result in substantial damage to equipment or risk of
personal injury to the user.
4.2 Connect the hardware
Prior to installation and commissioning
NOTICE
Reading associated manuals
Prior to installation, connecting up and commissioning, read the relevant sections in the
manual of the controller you are using, as well as the corresponding section of the "SIMATIC
RF300" system manual. When installing and connecting up, keep to the procedures
described in the manual.
NOTICE
Installation/removal with the power off
Wire up the PC or controller and modules to be connected only when the power is off. Make
sure that the power supply is turned off when installing/uninstalling the devices.

Commissioning
4.2 Connect the hardware
SIMATIC RF360R
Configuration Manual, 03/2022, C79000-G8976-C629-02 19
Interfaces
①Status LEDs
(status display of the reader and PROFINET
connection)
④Interface for PROFINET IO
X1 P1R (M12, 4-pin, D-coded)
②Operation LEDs
(operating states of the reader)
⑤Interface for PROFINET IO
X1 P2R (M12, 4-pin, D-coded)
1)
③Interface for the power supply
X80 (M12, 4-pin, L-coded)
Figure 4-1 Interface of the SIMATIC RF360R reader
1) You can loop-through PROFINET IO via the M12 round socket ⑤.
Requirement
•The reader has been mounted.
•Only wire the reader when the supply voltage is switched off.
NOTICE
Only use pre-fabricated cables in connection with high-impedance loads.
When using pre-fabricated cables, ensure that the conductor (L2) that is or will be
connected to pin 4 of the RF360R is only connected to high-impedance loads (> 22 Kilohm).
If this cannot be ensured, the conductor may not be connected to pin 4 of the RF360R
socket.

Commissioning
4.3 Network topology
SIMATIC RF360R
20 Configuration Manual, 03/2022, C79000-G8976-C629-02
Procedure
Proceed as follows to install the reader:
1. Connect the reader to a PC or switch or to a controller using an Ethernet cable ④.
Use a connecting cable with an M12 plug (4-pin).
2. If necessary, connect the reader to another SIMATIC RF360R reader ⑤.
Use a connection cable with an M12 plug (4-pin) to loop-through PROFINET IO.
3. Connect the reader to the power supply ③using the connecting cable.
The reader is ready for operation when the "R/S" LED is lit/flashes green. If the "R/S" LED
flashes, the reader is waiting for a connection. If the "R/S" LED is lit constantly, the reader is
connected to the controller.
You can find detailed information on mounting as well as ordering data (reader, connecting
cable, wide range power supply, etc.) in the "SIMATIC RF300" system manual.
4.3 Network topology
The communication network can be designed as line/series, star or ring topology.
Figure 4-2 Configuration graphic of a line/series topology
With a linear/series topology, remember that if the communications connection of a reader to
the controller is interrupted, the communications connection to all downstream readers is
also interrupted.