Siemens SIMATIC V2 User manual

IFP V2, IFP V2 PRO, IFP V2 ETH
SIMATIC HMI
Industrial Flat Panels V2
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions
03/2023
A5E46641410
-AE
Preface
Overview
1
Safety instructions
2
Installing and connecting
the device
3
Commissioning the IFP
4
Operating the IFP
5
Device maintenance and
repair
6
Technical information
7
Technical Support
A
Markings and symbols
B
List of abbreviations
C

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E46641410-AE
Ⓟ
04/2023 Subject to change
Copyright © Siemens AG 2023.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 3
Preface
These operating instructions contain all the information you need for commissioning and
using the Industrial Flat Panel SIMATIC IFP V2 and the Transceiver Unit.
These operating instructions are intended both for programming and testing personnel who
commission the devices and connect them to other units (automation systems, programming
devices), and for service and maintenance technicians who carry out maintenance work or
fault analyses.
Basic knowledge required
A solid background in personal computers and Microsoft operating systems is required to
understand this manual. General knowledge in the field automation control engineering is
recommended.
Scope of the operating instructions
These operating instructions apply to the following SIMATIC IFP V2 devices with article
numbers 6AV7863-.....-2...:
•SIMATIC IFP1200 V2, IFP1500 V2, IFP1900 V2, IFP2200 V2, IFP2400 V2
•SIMATIC IFP1200 V2 extended, IFP1500 V2 extended, IFP1900 V2 extended, IFP2200 V2
extended, IFP2400 V2 extended
•SIMATIC IFP1500 V2 ETH, IFP1900 V2 ETH, IFP2200 V2 ETH, IFP2400 V2 ETH
•SIMATIC IFP1200 V2 PRO, IFP1500 V2 PRO, IFP1900 V2 PRO, IFP2200 V2 PRO,
IFP2400 V2 PRO
These operating instructions also apply for the Transceiver Unit with the article number
6AV7860-3EH00-0AA0.
Conventions
The following conventions apply in these operating instructions:
•The term "device" is used for all SIMATIC IFP V2 devices, SIMATIC IFP V2 PRO devices and
the Transceiver Unit.
•The term "IFP" is also used for all SIMATIC IFP V2 devices and SIMATIC IFP V2 PRO devices.
•The devices IFP1200 V2, IFP1500 V2, IFP1900 V2, IFP2200 V2 and IFP2400 V2 are referred
to as "standard versions" of the SIMATIC IFP V2 devices.
•The devices IFP1200 V2 extended, IFP1500 V2 extended, IFP1900 V2 extended,
IFP2200 V2 extended and IFP2400 V2 extended are referred to as "extended versions" of
the SIMATIC IFP V2 devices.
•The devices IFP1500 V2 ETH, IFP1900 V2 ETH, IFP2200 V2 ETH and IFP2400 V2 ETH are
referred to as "ETH versions" or "Ethernet Monitors".

Preface
IFP V2, IFP V2 PRO, IFP V2 ETH
4Operating Instructions, 03/2023, A5E46641410-AE
•The standard versions, extended versions and Ethernet Monitors are referred to as "built-in
devices".
•The devices IFP1200 V2 PRO, IFP1500 V2 PRO, IFP1900 V2 PRO, IFP2200 V2 PRO and
IFP2400 V2 PRO are referred to as "PRO devices".
•The projective-capacitive multi-touch screen of the devices is also referred to as "capacitive
multi-touch screen" or "touch screen".
The following applies to the possible operating modes of an IFP:
•In "standard mode", an IFP is directly connected to the PC via a USB cable and a
DVI/DisplayPort cable ≤5 m long.
•In "Extended mode", an extended version or a PRO device can be connected via a Cat. 6A
Ethernet cable > 5 m and the Transceiver Unit connected to the PC.
•In "Commissioning" mode, an Ethernet Monitor is prepared for "Ethernet" mode. In
"Ethernet" mode, the PC and Ethernet Monitor are connected with an Ethernet cable
which transfers all signals for operator control and monitoring.
Figures
This manual contains figures of the described devices. The supplied device might differ in
some details from the figures. Within some of the figures, one device is used to represent
several devices.
Picture components are marked with black position numbers on a white background ①, ②,
③, ...
Steps in the figures are identified with white process numbers on a black background
according to the sequence in which they have to be executed: , , , ...
History
The following released versions of these operating instructions have been published to date:
Edition
Comment
08/2019
First Edition
08/2020 Description of the following devices added:
•Built-in devices IFP1200 V2, IFP1200 V2 extended
•Built-in devices IFP1500 V2 ETH, IFP1900 V2 ETH, IFP2200 V2 ETH, IFP2400 V2 ETH
•PRO devices IFP1200 V2 PRO and IFP2400 V2 PRO
08/2021
Description of approvals CE, UL, FM, and ATEX/IECEx updated, CCC added
11/2022
Description of approvals UKCA added and UKEX added.
03/2023
Description of approvals UL Hazardous updated.

IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 5
Table of contents
Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................ 8
1.1 Product description.............................................................................................................. 8
1.2 Scope of delivery of the IFPs............................................................................................... 10
1.3 Structure of the built-in devices.......................................................................................... 11
1.4 Design of the PRO devices.................................................................................................. 12
1.4.1 PRO devices for support arm (not extendable, flange top)................................................... 12
1.4.2 PRO devices for pedestal (extendable, flange bottom) ........................................................ 14
1.4.3 PRO devices for support arm (extendable, round tube) ....................................................... 15
1.5 Interfaces .......................................................................................................................... 17
1.6 System components and accessories.................................................................................. 17
1.6.1 System components for IFPs .............................................................................................. 18
1.6.2 System components for PRO devices .................................................................................. 20
1.6.3 Accessories........................................................................................................................ 24
2 Safety instructions............................................................................................................................... 26
2.1 General safety instructions................................................................................................. 26
2.2 Notes on use ..................................................................................................................... 28
2.3 Use in hazardous areas ...................................................................................................... 32
3 Installing and connecting the device .................................................................................................. 33
3.1 Preparing for installation.................................................................................................... 33
3.1.1 Checking the delivery package ........................................................................................... 33
3.1.2 Built-in devices .................................................................................................................. 34
3.1.2.1 Permitted mounting positions............................................................................................ 34
3.1.2.2 Required clearance ............................................................................................................ 36
3.1.2.3 Preparing the mounting cutout .......................................................................................... 37
3.1.2.4 Installing the strain relief plate........................................................................................... 38
3.1.3 PRO devices ....................................................................................................................... 39
3.1.3.1 Permitted mounting positions............................................................................................ 39
3.1.4 Transceiver Unit................................................................................................................. 40
3.1.4.1 Permitted mounting positions............................................................................................ 40
3.1.4.2 Required clearance ............................................................................................................ 41
3.1.4.3 Fastening the mounting rail ............................................................................................... 41
3.2 Installing the built-in device ............................................................................................... 42
3.2.1 Notes on installation.......................................................................................................... 42
3.2.2 Positions of the mounting clips .......................................................................................... 43
3.2.3 Fastening the built-in device using mounting clips ............................................................. 45
3.3 Mounting the PRO device................................................................................................... 47
3.3.1 Notes on mounting............................................................................................................ 47

Table of contents
IFP V2, IFP V2 PRO, IFP V2 ETH
6Operating Instructions, 03/2023, A5E46641410-AE
3.3.2 PRO devices for support arm (not extendable, flange top) and for pedestal (extendable,
flange bottom) .................................................................................................................. 48
3.3.3 PRO devices for support arm (extendable, round tube) ....................................................... 51
3.4 Mounting the Transceiver Unit........................................................................................... 54
3.5 Connecting the device ....................................................................................................... 56
3.5.1 Notes on connection.......................................................................................................... 56
3.5.2 Equipotential bonding ....................................................................................................... 58
3.5.3 Connecting the power supply ............................................................................................ 61
3.5.4 Connecting IFP Standard, Extended and PRO to a PC........................................................... 63
3.5.4.1 Important notes for connecting.......................................................................................... 63
3.5.4.2 Connecting the standard version to a PC ............................................................................ 63
3.5.4.3 Connecting the extended version or PRO device to a PC...................................................... 64
3.5.5 Connecting the Ethernet Monitor to a PC ........................................................................... 68
3.5.5.1 Overview........................................................................................................................... 68
3.5.5.2 Connection variants........................................................................................................... 69
3.5.6 Connecting a USB device to the IFP .................................................................................... 69
3.5.7 Securing the cables............................................................................................................ 70
3.5.7.1 Securing cables at the IFP................................................................................................... 70
3.5.7.2 Securing cables at the Transceiver Unit .............................................................................. 71
3.5.7.3 Securing cables for use in hazardous areas......................................................................... 71
3.6 Removing the device ......................................................................................................... 72
3.6.1 Removing the built-in device.............................................................................................. 72
3.6.2 Removing a PRO device...................................................................................................... 73
3.6.3 Removing Transceiver Unit................................................................................................. 74
4 Commissioning the IFP ........................................................................................................................ 75
5 Operating the IFP................................................................................................................................. 76
5.1 Operator input options ...................................................................................................... 76
5.2 Operating the capacitive multi-touch screen ...................................................................... 77
5.3 Extended functions............................................................................................................ 79
6 Device maintenance and repair........................................................................................................... 80
6.1 General information on maintenance and servicing............................................................ 80
6.2 Cleaning the device ........................................................................................................... 80
6.3 Spare parts and repairs ...................................................................................................... 81
6.4 Ethernet Monitors - Diagnostics and reset .......................................................................... 82
6.4.1 Diagnostics screen ............................................................................................................. 82
6.4.2 Restoring the factory settings for an Ethernet Monitor........................................................ 83
6.5 Recycling and disposal ....................................................................................................... 83
7 Technical information ......................................................................................................................... 84
7.1 Certificates and approvals.................................................................................................. 84
7.2 Electromagnetic compatibility............................................................................................ 91
7.3 Mechanical environmental conditions ................................................................................ 93
7.3.1 Storage conditions............................................................................................................. 93
7.3.2 Operating Conditions......................................................................................................... 93

Table of contents
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 7
7.4 Climatic ambient conditions............................................................................................... 94
7.4.1 Long-term storage ............................................................................................................. 94
7.4.2 Transport and short-term storage....................................................................................... 94
7.4.3 Operating Conditions......................................................................................................... 94
7.5 Information on insulation tests, protection class and degree of protection .......................... 95
7.6 Dimension drawings .......................................................................................................... 97
7.6.1 Dimension drawing of the IFP1200 V2 and IFP1200 V2 extended ....................................... 97
7.6.2 Dimension drawing of the IFP1500 V2 and IFP1500 V2 extended ....................................... 98
7.6.3 Dimension drawing of the IFP1900 V2 and IFP1900 V2 extended ....................................... 99
7.6.4 Dimension drawing of the IFP2200 V2 and IFP2200 V2 extended ..................................... 100
7.6.5 Dimension drawing of the IFP2400 V2 and IFP2400 V2 extended ..................................... 101
7.6.6 Dimension drawing of the IFP1500 V2 ETH....................................................................... 102
7.6.7 Dimension drawing of the IFP1900 V2 ETH....................................................................... 103
7.6.8 Dimension drawing of the IFP2200 V2 ETH....................................................................... 104
7.6.9 Dimension drawing of the IFP2400 V2 ETH....................................................................... 105
7.6.10 Dimension drawing of the IFP1200 V2 PRO ...................................................................... 106
7.6.11 Dimension drawing of the IFP1500 V2 PRO ...................................................................... 109
7.6.12 Dimension drawing of the IFP1900 V2 PRO ...................................................................... 112
7.6.13 Dimension drawing of the IFP2200 V2 PRO ...................................................................... 115
7.6.14 Dimension drawing of the IFP2400 V2 PRO ...................................................................... 118
7.6.15 Dimension drawing of the Transceiver Unit ...................................................................... 122
7.7 Rating plate ..................................................................................................................... 123
7.8 Technical specifications of the IFPs................................................................................... 124
7.9 Technical specifications of the Transceiver Unit ................................................................ 126
7.10 Interface description........................................................................................................ 127
7.10.1 24 V DC ........................................................................................................................... 127
7.10.2 DVI-D............................................................................................................................... 127
7.10.3 DisplayPort ...................................................................................................................... 128
7.10.4 USB hub Type A ............................................................................................................... 129
7.10.5 USB Type B ...................................................................................................................... 129
7.10.6 Ext-Link ........................................................................................................................... 130
7.10.7 Ethernet .......................................................................................................................... 130
A Technical Support .............................................................................................................................. 131
A.1 Service and support ......................................................................................................... 131
A.2 Troubleshooting .............................................................................................................. 132
A.3 Information about the manufacturer................................................................................ 132
B Markings and symbols....................................................................................................................... 133
B.1 Safety-relevant symbols................................................................................................... 133
C List of abbreviations .......................................................................................................................... 135
Glossary ............................................................................................................................................. 136
Index .................................................................................................................................................. 137

IFP V2, IFP V2 PRO, IFP V2 ETH
8Operating Instructions, 03/2023, A5E46641410-AE
Overview
1
1.1 Product description
SIMATIC IFPs are industrial grade LCD monitors with a brilliant TFT display that can be
connected to SIMATIC IPCs and to almost all commercially available PCs.
Features of the built-in devices
•Rugged front in different design versions
•Brilliant TFT display with high viewing angle, Full HD resolution and up to 16 million colors
•Capacitive multi-touch screen in all sizes, switchable via software from multi-touch mode
to single-touch mode
•Can be placed up to 5 m from the IPC
•DVI-D/DisplayPort V1.1/1.2 interface
•Multi-monitoring support
•Backlight can be dimmed via software
•Two USB 2.0 ports
•Power supply 24 V DC, AC power supply unit available as system component
•In installed condition, front degree of protection IP65 or Enclosure Type 4X/12 (indoor use
only, front face only)
Features of the extended versions
The extended versions have a DisplayPort V1.2 interface and the following features in
addition to the built-in devices:
•Possible via Transceiver Unit up to 100 m distance to the PC

Overview
1.1 Product description
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 9
Features of the Ethernet Monitors
The Ethernet Monitors have a DisplayPort V1.1 interface and the following additional features
as compared to the built-in devices:
•Configuration and operation in the Ethernet/LAN network
•Length of the Ethernet/LAN connection as customary with conventional LAN technology
•Automatic establishment of connection to SIMATIC IPC
•Automatic configuration using 1:1 cable connection
•Ethernet Monitor software and monitor diagnostics function
Features of the PRO devices
The PRO devices are connected to a 24 V DC power supply and have the following features in
addition to the extended versions:
•All-round dust-proof and splash-proof with degree of protection IP65 and Enclosure Type
4X/12 (indoor use only)
•Can be mounted directly on the machine
Note
This is not suitable
for UL hazardous location.
•Device versions for mounting:
–PRO device for pedestal (extendable, flange bottom)
–PRO device for support arm (not extendable, flange top)
–PRO device for support arm (extendable, round tube)
Adapters and adapter sets that can be ordered separately support mounting systems from
various manufacturers.
–Base adapter, included in the product package of PRO devices for pedestal (extendable,
flange bottom) and for support arm (not extendable, flange top).
–With PRO devices for support arm (extendable, round tube):
- Cover for the mechanical interface below, included in the product package
- Flange mount adapter available as accessory

Overview
1.2 Scope of delivery of the IFPs
IFP V2, IFP V2 PRO, IFP V2 ETH
10 Operating Instructions, 03/2023, A5E46641410-AE
1.2 Scope of delivery of the IFPs
The product package includes the following components:
Name
Figure
Number
IFP
1
Accessory kit
"Mounting clips 1
and
power supply connector"
12
1
Strain relief plate
1
Including 3 screws T10,
M3x8
1
Base adapter
2
Including 4 screws T20,
M4x12
1
Cover for mechanical inter-
face 3
Including 4 screws T20,
M4x12
1
"Connecting cables" acces-
sory kit 4
DisplayPort cable, length 2 m
1
USB cable Type B connector - Type A connector, length 2 m
1
Ethernet connecting cable
5
, length 2 m
1
Ferrites
6
Ferrite for power supply cables, white
1
Ferrite for the Ethernet cable to the Transceiver Unit, black
1
1 Only for built-in devices, not for PRO devices
2Only with PRO devices for pedestal (extendable, flange bottom) and for support arm (not extend-
able, flange top)
3Only with PRO devices for support arm (extendable, round tube)
4Only for standard versions and Ethernet Monitors
5Only for Ethernet Monitors
6
Only for extended versions and PRO devices

Overview
1.3 Structure of the built-in devices
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 11
1.3 Structure of the built-in devices
This section describes the structure of the built-in devices using the example of the
IFP1900 V2 extended.
Front view and side view
①
Display and capacitive multi-touch screen
②
Recesses for mounting clips
③
Mounting seal
Bottom view
①
Interfaces
②
Recesses for mounting clips

Overview
1.4 Design of the PRO devices
IFP V2, IFP V2 PRO, IFP V2 ETH
12 Operating Instructions, 03/2023, A5E46641410-AE
Rear view
①
Position of rating plate
②
Threaded holes for fastening the strain relief plate
1.4 Design of the PRO devices
1.4.1 PRO devices for support arm (not extendable, flange top)
This section describes the structure of the PRO devices for support arm (not extendable,
flange top) using the example of the IFP1900 PRO for support arm (not extendable, flange
top).

Overview
1.4 Design of the PRO devices
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 13
Front view and side view
①
Display and capacitive multi-touch screen
②
Enclosure
③
Backplane cover
Top view
①
Mechanical interface for fastening

Overview
1.4 Design of the PRO devices
IFP V2, IFP V2 PRO, IFP V2 ETH
14 Operating Instructions, 03/2023, A5E46641410-AE
Rear view
①
Mechanical interface for fastening
②
Rating plate
③
Enclosure
④
Backplane cover
1.4.2 PRO devices for pedestal (extendable, flange bottom)
This section describes the structure of the PRO devices for pedestal (extendable, flange
bottom) using the example of the IFP1900 PRO for pedestal (extendable, flange bottom).
Front view and side view
①
Display and capacitive multi-touch screen
②
Enclosure
③
Backplane cover

Overview
1.4 Design of the PRO devices
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 15
Bottom view
①
Mechanical interface for fastening
Rear view
①
Backplane cover
②
Enclosure
③
Rating plate
④
Mechanical interface for fastening
1.4.3 PRO devices for support arm (extendable, round tube)
This section describes the structure of the PRO devices for support arm (extendable, round
tube) using the example of the IFP1500 PRO for support arm (extendable, round tube).

Overview
1.4 Design of the PRO devices
IFP V2, IFP V2 PRO, IFP V2 ETH
16 Operating Instructions, 03/2023, A5E46641410-AE
Front view and side view
①
Display and capacitive multi-touch screen
②
Enclosure
③
Mechanical interface for fastening (round tube)
④
Terminal compartment cover
⑤
Mechanical interface to the optional Extension Unit or to the supplied cover
Rear view
①
Mechanical interface for fastening (round tube)
②
Terminal compartment cover
③
Rating plate
④
Mechanical interface to the optional Extension Unit or to the supplied cover
⑤
Lower cover, included in the product package

Overview
1.5 Interfaces
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 17
1.5 Interfaces
Standard versions
①
Connection for functional ground
④
X71 DVI-D interface
②
X80 connector for 24 V DC power supply
⑤
X61/X62 USB Type A
③
X70 DisplayPort interface
⑥
X60 USB Type B
Extended versions and PRO devices
①Connection for functional ground ④X71 Ext-Link interface to the Trans-
ceiver Unit
②
X80 connector for 24 V DC power supply
⑤
X61/X62 USB Type A
③
X70 DisplayPort interface
⑥
X60 USB Type B
Ethernet Monitors
①
Connection for functional ground
⑤
X70 DisplayPort interface
②
X80 connector for 24 V DC power supply
⑥
X61/X62 USB Type A
③
X1 Ethernet port to the PC
⑦
X60 USB Type B
④
Reset button
1.6 System components and accessories
System components are products that have been developed for a specific system and can
not be used in general, for example, like the base adapter. System components are always
directly related to a core product.

Overview
1.6 System components and accessories
IFP V2, IFP V2 PRO, IFP V2 ETH
18 Operating Instructions, 03/2023, A5E46641410-AE
Accessories can typically be used for multiple devices from the same or different device
families, for example, batteries, touch pens or protective membranes.
1.6.1 System components for IFPs
Transceiver Unit for extended versions and PRO devices
With the Transceiver Unit you can bridge a distance of up to 100 m between a PC and an
extended version or a PRO device. The Transceiver Unit is mounted close to the PC.
The Transceiver Unit can be attached on a DIN rail or in various positions on a wall using the
mounting material supplied.
①Hole for the screw to fasten the mounting
rail
⑧"LNK" LED
②
Guide for the "left" mounting rail
⑨
Mounting rail
③
Connection for functional ground
⑩
Lower elongated hole of the mounting rail
④
X80 connector for 24 V DC power supply
⑪
X70 DisplayPort interface
⑤
Opening for "left" strain relief element
⑫
Opening for "right" strain relief element
⑥
X71 Ext-Link interface to the IFP
⑬
X60 USB Type B
⑦
Guide for the "rear" mounting rail
⑭
Guide for the "right" mounting rail
Article number of the Transceiver Unit: 6AV7860-3EH00-0AA0
Scope of delivery
•A Transceiver Unit
•One mounting rail for attachment to DIN rail or wall mounting
•Strain relief elements
•One DisplayPort cable, length 0.5 m
•One USB cable Type B connector - Type A connector, length 0.5 m
•A power supply connector 24 V DC, 2-pin

Overview
1.6 System components and accessories
IFP V2, IFP V2 PRO, IFP V2 ETH
Operating Instructions, 03/2023, A5E46641410-AE 19
•A ferrite for the power supply cables, white
•One ferrite for the Ethernet line to the IFP, black
Functions of the "LNK" LED
•LED lit green: Active link available
•LED not illuminated: No active link available
AC power supply unit for built-in devices
Connect a built-in device to the power supply via the AC power supply unit, input voltage
range 100 ... 240 V. Use the supplied mounting material to fasten the AC power supply unit
on the rear of the built-in device.
Article number of the AC power supply unit: 6AV7860-3PA00-0AA0
You can find the documentation for the AC power supply unit via the article number on the
Internet (https://support.industry.siemens.com).
WARNING
Do not use the power supply unit in hazardous areas.
The power supply unit is not approved for use in hazardous areas. If the power supply unit is
mounted on a built-in device with Ex approval, the Ex approval of the built-in device expires.
Operation of the power supply unit in a hazardous area may result in an explosion, death or
serious injury.
Never operate the power supply unit in a hazardous area.

Overview
1.6 System components and accessories
IFP V2, IFP V2 PRO, IFP V2 ETH
20 Operating Instructions, 03/2023, A5E46641410-AE
1.6.2 System components for PRO devices
Base adapter
You use the base adapter to mount PRO devices for support arm (not extendable, flange top)
or for pedestal (extendable, flange bottom) on the support arm or on the pedestal. A base
adapter is included with the product package of the corresponding PRO device. The base
adapter can also be ordered separately.
①
Seal
②
Channel cable
③
Mechanical interface to the PRO device
④
Cover
⑤
Mechanical interface to the support arm or pedestal including seal
Article number: 6AV7674-1KA00-0AA0
Adapter sets and couplings
The following mechanical adapter versions are also available for mounting a PRO device
for support arm (not extendable, flange top) or for pedestal (extendable, flange bottom) via
the base adapter:
•Adapter set VESA75 for VESA75-compatible systems, Article number
6AV7674-0KE00-0AA0
•Adapter set VESA100 for VESA100-compatible systems, Article number
6AV7674-0KD00-0AA0
In addition, other manufacturers offer support arm or pedestal systems with mechanical
interfaces or adapters for Siemens PRO devices, e.g. RITTAL, ROLEC, BERNSTEIN, HASEKE,
ROSE. Observe the specifications provided by the respective manufacturer.