Siemens Sitrans F Series Parts list manual

SITRANS F
Coriolis Flowmeters
FCT030 Profibus (From firmware
4.0)
Function Manual
06/2018
A5E39931906-AB
Introduction 1
Communication 2
Cable specifications 3
Definitions 4

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E39931906
Ⓟ 05/2018 Subject to change
Copyright © Siemens AG 2018.
All rights reserved

Table of contents
1 Introduction...................................................................................................................................................5
1.1 Purpose of this documentation.................................................................................................5
1.2 Document history.....................................................................................................................5
1.3 Product compatibility................................................................................................................6
2Communication.............................................................................................................................................7
2.1 Features...................................................................................................................................7
2.2 Installation in hazardous area..................................................................................................7
2.3 Profibus....................................................................................................................................7
2.4 Wall mount housing transmitter exploded view........................................................................9
2.5 Changing Profibus termination at the transmitter cassette....................................................10
2.6 Connecting the Profibus (CH1)..............................................................................................12
2.7 Installation check....................................................................................................................13
2.8 Cyclic services.......................................................................................................................14
2.9 Cyclic data exchange.............................................................................................................15
2.10 Acyclic communication...........................................................................................................26
2.11 Access Control.......................................................................................................................63
2.12 Alarm, error, and system messages......................................................................................64
2.12.1 Introduction............................................................................................................................64
2.12.2 Diagnosis Response..............................................................................................................64
3 Cable specifications....................................................................................................................................67
4 Definitions...................................................................................................................................................69
Index...........................................................................................................................................................73
FCT030 Profibus (From firmware 4.0)
Function Manual, 06/2018, A5E39931906-AB 3

Table of contents
FCT030 Profibus (From firmware 4.0)
4Function Manual, 06/2018, A5E39931906-AB

Introduction 1
1.1 Purpose of this documentation
This manual contains all information needed to integrate the process instruments into a
communications network. The manual is aimed at control system designers, system
integrators, instrument engineers.
In order to operate safety and for more detailed information you need the product specific
manual. Available for download from Flow documentation (http://www.siemens.com/
flowdocumentation).
This manual applies to the SITRANS FCT030 transmitter Profibus DP/PA version only. The
FCT030 transmitter can be used in combination with the following sensors:
Mass 2100
FC300
FCS400 and FCS300
In order to operate a Coriolis flow meter, you also need Operating Instructions. See Flow
documentation (http://www.siemens.com/flowdocumentation)
1.2 Document history
The following table shows major changes in the documentation compared to the previous
edition.
The most important changes in the documentation when compared with the respective
previous edition are given in the following table.
Edition Note
06/2018 Second edition
06/2017 First edition
Use the device to measure process medium in accordance with the information in the
Operating Instructions.
Note
Use in a domestic environment
This Class A Group 1 equipment is intended for use in industrial areas.
In a domestic environment this device may cause radio interference.
FCT030 Profibus (From firmware 4.0)
Function Manual, 06/2018, A5E39931906-AB 5

1.3 Product compatibility
Edition Remarks Product compatibility Compatibility of device integration package
06/2017 First revision HW revision 03
Compact FW revision 4.xx.xx-xx
Remote FW revision 4.xx.xx-xx
Service channel: SIMATIC
V8.2 Service Pack 1 or later
5.00.xx-xx
Modbus: SIMATIC V8.2 Serv‐
ice Pack 1 or later
5.00.xx-xx
HART: SIMATIC V8.2 Serv‐
ice Pack 1 or later
5.00.xx-xx
HART: SITRANS DTM V4.1 5.00.xx-xx
HART: AMS Device manager
V12
5.00.xx-xx
PROFIBUS: SIMATIC V8.2
Service Pack 1 or later
1.00.xx-xx
PROFIBUS : SITRANS DTM
V4.1
1.00.xx-xx
05/2015 Aerated Flow
parameters
added
HW revision 02
Compact FW revision
3.02.02-01
Remote FW revision 2.02.02-01
SIMATIC PDM HART 4.00.00-00
SIMATIC PDM Service chan‐
nel
4.00.00-00
AMS Device Manager HART 4.00.00-02
SITRANS DTM HART 4.00.00-00
375 Field Communicator
HART
4.00.00-02
05/2014 Description of
new parame‐
ters for spare
part replace‐
ment
HW revision 02
Compact FW revision 3.02.01
Remote FW revision 2.02.01
SIMATIC PDMAMS Device
ManagerSITRANS DTM375
Field Communicator
3.00.00-00
12/2013 Various LUI
functions, for
example wiz‐
ards Various
transmitter
functionalities
HW revision 02
Compact FW revision 3.02.00
Remote FW revision2.02.00
SIMATIC PDMAMS Device
ManagerSITRANS DTM375
Field Communicator
EDD Version 2.00.00
06/2012 CT chapter in‐
cluded
HW revision 01
Compact FW revision
3.00.00-10
Remote FW revision2.00.00-30
SIMATIC PDM EDD Version 1.00.00
03/2012 First edition HW revision 01
Compact FW revision 2.00.0x
Remote FW revision
2.00.0x
SIMATIC PDM EDD Version 1.00.00
Introduction
1.3 Product compatibility
FCT030 Profibus (From firmware 4.0)
6Function Manual, 06/2018, A5E39931906-AB

Communication 2
2.1 Features
The device provides the following features:
● PROFIBUS DP communication up to 12 Mbit/s
● Automatic baud rate adaption
● PROFIBUS PA communication
● Automatic baud rate adaption
● Cyclic communication
● Acyclic communication to SIMATIC S7 or other PLCs
● Acyclic communication to SIMATIC PDM or other parameterization tools
● Support of high availability systems like SIMATIC S7 H
● Support of PROFIBUS PA Profile for Process Control Devices V4.0 and V3
● Automatic GSD adaption
● Support of up to 15 modules (process values and control values), in cyclic communication
● PROFIBUS clock synchronization by master
2.2 Installation in hazardous area
The PROFIBUS DP module is not allowed for use in hazardous areas.
The PROFIBUS PA module is allowed for use in hazardous areas.
2.3 Profibus
The transmitter has a modular design with discrete, replaceable electronic modules and
connection boards to maintain separation between functions and facilitate field service. All
modules are fully traceable and their provenance is included in the transmitter setup.
The bus termination can be activated via a switch internal in the transmitter. The bus
termination switch is set to off by default. If the internal switch is not used for termination an
external separate bus terminator must be installed. The internal switch is located to on the
transmitter PCBA module (9)
FCT030 Profibus (From firmware 4.0)
Function Manual, 06/2018, A5E39931906-AB 7

Transmitter exploded view
DED
/
E
①Display cover ⑫Transmitter housing
②Local display (HMI) ⑬Terminal space
③Connector for HMI ⑭Power supply terminal protection cover
④SD card (SensorFlash) ⑮Lid for terminal connections
⑤DIP switch (for custody transfer) ⑯Wiring tool
⑥DIP switch (for HART) ⑰I/O cassette (optional)
⑦HMI port ⑱I/O configuration keys (optional)
⑧USB service port ⑲a M12 socket
⑨Transmitter cassette ⑲b Terminal housing
⑩Heatsink cover for power supply module ⑳a Sensor module (compact version)
⑪Cable entry ⑳b Sensor module (remote version)
Figure 2-1 Transmitter exploded view
Communication
2.3 Profibus
FCT030 Profibus (From firmware 4.0)
8Function Manual, 06/2018, A5E39931906-AB

2.4 Wall mount housing transmitter exploded view

①Display glass with retaining ring ⑩Foam bottom
②Power supply module (complete) ⑪Hinge pin
③SensorFlash (SD card) ⑫Housing
④Transmitter cassette ⑬Ground connect set
⑤IO cassette ⑭Backplane module
⑥HMI module ⑮Power supply connector cover
⑦Foam top ⑯Front cover enclosure
⑧Foam plugs ⑰Front cover mounting screws
⑨Sensor module (analog version)
Barrier module (digital version)
Figure 2-2 Wall mount housing transmitter exploded view
Communication
2.4 Wall mount housing transmitter exploded view
FCT030 Profibus (From firmware 4.0)
Function Manual, 06/2018, A5E39931906-AB 9

2.5 Changing Profibus termination at the transmitter cassette
To change the termination of the Profibus, it is required to remove the transmitter module out
of the transmitter. This can be done following below instructions.
1. Isolate the device from power.
2. Using tool no. 9, unscrew the locking screw of the display and remove the display lid using
tool no. 3 as a wrench bar if necessary.
3. Carefully remove display and cable plug.
Note
Use a screwdriver, tool no. 11, to release the display as shown in photo below.
The display is held in place with three clips.
Communication
2.5 Changing Profibus termination at the transmitter cassette
FCT030 Profibus (From firmware 4.0)
10 Function Manual, 06/2018, A5E39931906-AB