Siemens SITRANS FUE1010 IP65 NEMA 4X User manual

12/2014Edition
Answers for industry.
Operating Instructions
Ultrasonic Flowmeters
SITRANS FUE1010 IP65 NEMA 4X - 7ME3500
SITRANS F

SITRANS F
Ultrasonic Flowmeters
FUE1010 IP65 NEMA 4X
Operating Instructions
12/2014
A5E03086491
-AC
Introduction
1
Safety notes
2
Description
3
Installing/mounting
4
Connecting
5
Commissioning
6
Functions
7
Alarm, error, and system
messages
8
Service and maintenance
9
Troubleshooting
10
Technical data
11
Appendix
A
Appendix
B

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: A5E03086491
Ⓟ
11/2014 Subject to change
Copyright © Siemens AG 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury
may
result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 3
Table of contents
1 Introduction............................................................................................................................................. 9
1.1 Preface......................................................................................................................................9
1.2 Items supplied...........................................................................................................................9
1.3 History.....................................................................................................................................10
1.4 Further Information .................................................................................................................10
2 Safety notes.......................................................................................................................................... 11
2.1 General safety instructions .....................................................................................................11
2.2 Warning Symbols....................................................................................................................12
2.3 Laws and directives ................................................................................................................13
2.4 Lithium batteries......................................................................................................................14
2.5 Installation in hazardous area.................................................................................................14
2.6 Safety Notes ...........................................................................................................................17
3 Description............................................................................................................................................ 23
3.1 FUE1010 features...................................................................................................................23
3.2 NEMA 4X Energy Transmitter ................................................................................................23
3.3 Applications.............................................................................................................................24
3.4 Theory of Operation................................................................................................................25
4 Installing/mounting................................................................................................................................ 31
4.1 Installation safety precautions ................................................................................................31
4.2 Determining a location............................................................................................................31
4.3 Use according to specifications ..............................................................................................32
4.4 Application Guidelines ............................................................................................................32
4.5 Mounting the Transmitter........................................................................................................33
5 Connecting ........................................................................................................................................... 35
5.1 Safety notes for connecting ....................................................................................................35
5.2 Transmitter Wiring...................................................................................................................38
5.2.1 Connecting Power...................................................................................................................38
5.2.2 Wiring Temperature Sensor to Transmitter ............................................................................41
5.3 Navigating the Menu...............................................................................................................46
5.4 Programming the Transmitter.................................................................................................49
5.5 Sensor Installation ..................................................................................................................55
5.5.1 Preliminary Installation Procedures........................................................................................55

Table of contents
FUE1010 IP65 NEMA 4X
4Operating Instructions, 12/2014, A5E03086491-AC
5.5.2 Sensor Identification and Selection........................................................................................ 59
5.5.3 Reflect Mount......................................................................................................................... 62
5.5.4 Direct Mount........................................................................................................................... 65
5.5.5 1012T Mounting Tracks ......................................................................................................... 70
5.5.6 Zero Flow Adjust Menu.......................................................................................................... 79
5.6 Mounting Temperature Sensors ............................................................................................ 83
5.7 Sensor Wiring......................................................................................................................... 86
6 Commissioning..................................................................................................................................... 87
6.1 General requirements ............................................................................................................ 87
6.2 Empty Pipe Set ...................................................................................................................... 89
6.3 Installation Menus.................................................................................................................. 92
7 Functions.............................................................................................................................................. 97
7.1 Selecting Flow Units .............................................................................................................. 97
7.2 Span Data............................................................................................................................ 102
7.3 Logger Control ..................................................................................................................... 104
7.4 Operation Adjust Menu Settings.......................................................................................... 110
7.5 Setting Relays...................................................................................................................... 113
7.6 Memory Control.................................................................................................................... 115
7.7 Analog Out Setup................................................................................................................. 116
7.8 Analog Input Setup .............................................................................................................. 118
7.9 Energy AnCal....................................................................................................................... 122
7.10 Analog Output Trim.............................................................................................................. 123
7.11 RTD Calibration.................................................................................................................... 126
7.12 Reflexor................................................................................................................................ 129
8 Alarm, error, and system messages.....................................................................................................141
9 Service and maintenance.....................................................................................................................143
9.1 Maintenance......................................................................................................................... 143
9.2 Technical support................................................................................................................. 143
9.3 Return procedures ............................................................................................................... 145
9.4 Battery disposal.................................................................................................................... 145
10 Troubleshooting...................................................................................................................................147
10.1 Troubleshooting ................................................................................................................... 147
10.2 F4 Reset Procedure............................................................................................................. 149
10.3 Test Facilities Graph Screen................................................................................................ 151
10.4 Site Setup Data.................................................................................................................... 162
10.5 Force Transmit..................................................................................................................... 167

Table of contents
FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 5
11 Technical data .................................................................................................................................... 171
11.1 Technical Data......................................................................................................................171
A Appendix............................................................................................................................................. 173
A.1 Certificates............................................................................................................................173
A.2 Ordering................................................................................................................................173
A.3 I/O Connections and Wiring..................................................................................................173
A.4 RS-232 Connection...............................................................................................................194
A.5 Flowrate Calibration and Calibration Tables.........................................................................205
B Appendix............................................................................................................................................. 209
B.1 Installation/Outline Drawings ................................................................................................209
Glossary ............................................................................................................................................. 211
Index................................................................................................................................................... 217
Tables
Table 5- 1 TB3 and TB4 Wiring.....................................................................................................................44
Table 5- 2 Keypad Function Chart ................................................................................................................48
Table 5- 3 Pipe Configuration Option List Definitions ...................................................................................54
Table 5- 4 Temperature Sensors ..................................................................................................................83
Table 7- 1 Totalizer Modes............................................................................................................................98
Table 7- 2 Totalizer Controls (the "n" in <Fn> = channel number)*............................................................101
Table 7- 3 Logger Control Menu Option List...............................................................................................107
Table 7- 4 Relay Option List........................................................................................................................114
Table 7- 5 Memory Control Menu ...............................................................................................................115
Table 7- 6 Analog Outputs ..........................................................................................................................116
Table 7- 7 Analog Out Setup Data Categories............................................................................................116
Table 7- 8 Analog Out Trim Menu Structure...............................................................................................123
Table 7- 9 RTD Calibrate Menu Structure...................................................................................................127
Table 7- 10 Inline Metal and Plastic Pipe Cable Connections ......................................................................131
Table 7- 11 Cursor Definitions.......................................................................................................................137
Table 7- 12 Diagnostic Data..........................................................................................................................139
Table 8- 1 Alarm Codes ..............................................................................................................................141
Table 10- 1 Troubleshooting Tips .................................................................................................................147
Table 10- 2 Description of Graph Screen Text Display Parameters.............................................................153
Table 10- 3 Hot Key Summary......................................................................................................................160
Table 10- 4 Site Setup Menu Items...............................................................................................................162

Table of contents
FUE1010 IP65 NEMA 4X
6Operating Instructions, 12/2014, A5E03086491-AC
Table 11- 1 Performance Specifications .......................................................................................................171
Table A- 1 Connection Diagrams and Part Numbers ..................................................................................173
Table A- 2 Input/Output Wiring (TB2) - 7ME39400AL00 and 7ME39400AL01 I/O Module (for
7ME3500 or 7ME3530 only) ......................................................................................................175
Table A- 3 Input/Output Wiring (TB3) - 7ME39400AL00 and 7ME39400AL01 I/O Module........................176
Table A- 4 Connection Diagrams and Part Numbers ..................................................................................177
Table A- 5 Input/Output Wiring (TB2) - 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module.......179
Table A- 6 Input/Output Wiring (TB3) - 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module.......180
Table A- 7 Input/Output Wiring (TB4) - 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module.......181
Table A- 8 Connection Diagrams and Part Numbers ..................................................................................182
Table A- 9 Input/Output Wiring (TB2) - 7ME39400AL04 Expanded I/O Module.........................................184
Table A- 10 Open Collector User Resistor Recommendations.....................................................................185
Table A- 11 Input/Output Wiring (TB3) - 7ME39400AL04 Expanded I/O Module.........................................186
Table A- 12 Input/Output Wiring (TB4) - 7ME39400AL04 Expanded I/O Module.........................................187
Table A- 13 Input/Output Wiring (TB3) - 7ME39406ML00 I/O Module (4-Channel) .....................................188
Table A- 14 Connection Diagrams and Part Numbers..................................................................................189
Table A- 15 Input/Output Wiring TB1 7ME39404SB00 - Analog Input Module (2 Chan/Dual Path).............190
Table A- 16 Input/Output Wiring TB2 7ME39404SB00 - Analog Input Module (2 Chan/Dual Path).............190
Table A- 17 Input/Output Wiring TB3 7ME39404SB00 - Analog Input Module (2 Chan/Dual Path).............190
Table A- 18 Input/Output Wiring TB4 7ME39404SB00 - Analog Input Module (2 Chan/Dual Path).............190
Table A- 19 Input/Output Wiring TB5 7ME39404SB00 - Analog Input Module (2 Chan/Dual Path).............191
Table A- 20 Connection Diagrams and Part Numbers..................................................................................192
Table A- 21 Input/Output Wiring TB1 7ME39400SA00 - Analog Input Module.............................................192
Table A- 22 Input/Output Wiring TB2 7ME39400SA00 - Analog Input Module.............................................193
Table A- 23 Input/Output Wiring TB3 and TB4 7ME39400SA00 - Analog Input Module..............................193
Figures
Figure 3-1 Typical Transmitter Label.............................................................................................................24
Figure 3-2 NEMA 4X Transmitter Case.........................................................................................................24
Figure 4-1 Pipe Mounting and Mounting Locations for Transmitter ..............................................................34
Figure 5-1 Input Power (J10) Wiring..............................................................................................................39
Figure 5-2 Analog Input Module Access .......................................................................................................42
Figure 5-3 Single Channel Temperature Sensor Inputs................................................................................42
Figure 5-4 Dual Channel Temperature Sensor .............................................................................................44

Table of contents
FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 7
Figure 5-5 KeyPad.........................................................................................................................................48
Figure 5-6 Typical Installation Menu Screen.................................................................................................49
Figure 5-7 Reflect Mount (Pipe shown from above in 12 o'clock position) ...................................................56
Figure 5-8 Direct Mount (Pipe shown from above in 12 o'clock position).....................................................57
Figure 5-9 Sensor Alignment (Horizontal Plane)...........................................................................................58
Figure 5-10 Pipe Surface Preparation.............................................................................................................59
Figure 5-11 Hi Precision Sensor Label............................................................................................................60
Figure 5-12 Reflect Mount with Mounting Frames and Spacer Bar................................................................62
Figure 5-13 Sensor..........................................................................................................................................64
Figure 5-14 Sensor Installation .......................................................................................................................64
Figure 5-15 Mylar Spacing Guide....................................................................................................................65
Figure 5-16 Wrap Strap Under Pipe and Attach to Adjusting Screw...............................................................66
Figure 5-17 Wrapping the Mylar Spacing Guide around the pipe (End View) ................................................68
Figure 5-18 Finding the Halfway Distance ......................................................................................................68
Figure 5-19 Aligning the Sensors for Direct Mode operation (End View) .......................................................69
Figure 5-20 Reflect Mount with Model 1012TN Mounting Track (Side View) .................................................71
Figure 5-21 Direct Mount 180° opposed with Mounting Tracks......................................................................74
Figure 5-22 Wrapping the Mylar Spacing Guide around the pipe (End View) ................................................76
Figure 5-23 Finding the Halfway Distance ......................................................................................................76
Figure 5-24 Track Rail Alignment....................................................................................................................77
Figure 5-25 REF and Number Index Pin Locations ........................................................................................78
Figure 5-26 Clamp-on Temperature Sensor ...................................................................................................84
Figure 5-27 Insert Temperature Sensor..........................................................................................................85
Figure 5-28 Sensor Cable Connections..........................................................................................................86
Figure 6-1 Final Setup...................................................................................................................................88
Figure 6-2 Measuring Flow............................................................................................................................88
Figure 7-1 Sensor Mounting Examples.......................................................................................................130
Figure 7-2 Adjacent Sensor Mounting.........................................................................................................131
Figure 7-3 In-Line Sensor Mounting............................................................................................................132
Figure 7-4 Spectra Graph Display Screen ..................................................................................................136
Figure 10-1 Test Facilities Graph Screen......................................................................................................152
Figure 10-2 Setting the MinDamp Factor......................................................................................................157
Figure 10-3 Envelope Threshold Adjustment................................................................................................159
Figure A-1 7ME39400AL00 and 7ME39400AL01 I/O Module.....................................................................174
Figure A-2 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module ...................................................178
Figure A-3 7ME39400AL04 Expanded I/O Module .....................................................................................183

Table of contents
FUE1010 IP65 NEMA 4X
8Operating Instructions, 12/2014, A5E03086491-AC
Figure A-4 7ME39404SB00 Analog Input Module.......................................................................................189
Figure A-5 Temperature Sensor Inputs .......................................................................................................191
Figure A-6 7ME39400SA00 - Analog Input Module.....................................................................................192
Figure A-7 1015CPC-N Serial Interface Cable............................................................................................195

FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 9
Introduction
1
1.1
Preface
These instructions contain all the information you need for using the device.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it as well as service and
maintenance engineers.
Note
It is the responsibility of the customer that the instructions and directions provided in the
manual are read, understood and followed by the relevant personnel before installing t
he
device.
1.2
Items supplied
●SITRANS F Transmitter
●SITRANS F literature CD
●For additional items refer to your packing slip.
Inspection
1. Check for mechanical damage due to possible improper handling during shipment. All
claims for damage are to be made promptly to the shipper.
2. Make sure the scope of delivery, and the information on the type plate corresponds to the
ordering information.

Introduction
1.3 History
FUE1010 IP65 NEMA 4X
10 Operating Instructions, 12/2014, A5E03086491-AC
1.3
History
The contents of these instructions are regularly reviewed and corrections are included in
subsequent editions. We welcome all suggestions for improvement.
The following table shows the most important changes in the documentation compared to
each previous edition.
Edition
Remarks
09/2010 First Edition of Operating Instructions for SITRANS FUE1010 IP65 NEMA 4X energy
flowmeter.
01/2013 Second Edition of Operating Instructions for SITRANS FUE1010 IP65 NEMA 4X energy
flowmeter.
The most important changes are as follows:
•To use Si-Ware download the program at [http://www.siemens.com/siware
•Expanded I/O Module Installation Wiring Diagram 1010N-7-7 has been updated to
Revision 08.
•I/O Module Installation Wiring Diagram 1010N-2-7 has been updated to Revision 05.
•Analog Input Module Installation Drawing 1010N-5DS2-7 has been updated to Revi-
sion 06. Appendix I/O Connection and Wiring chapter has been updated.
12/2014 Third Edition of Operating Instructions for SITRANS FUE1010 IP65 NEMA 4X energy
flowmeter.This document replaces all previous instructions for use.The most important
changes are as follows:
The most important changes are as follows:
•Removal of CC110 couplant compund references.
•Force Transmit and Forced Frrequency updated notes.
•Transmitter Power connection and Navigating The Menu procedure updates.
•Updated Logger Control procedures.
1.4
Further Information
Product information on the Internet
The Operating Instructions are available on the CD-ROM shipped with the device and on the
Internet on the Siemens homepage, where further information on the range of SITRANS F
flow meters may also be found: Product information on SITRANS F in the Internet
(http://www.siemens.com/sitransf)
Worldwide contact person
If you need more information or have particular problems not covered sufficiently by the
operating instructions, please get in touch with your contact person. You can find contact
information for your local contact person on the Internet: www.siemens.com Local contact
person (http://www.automation.siemens.com/partner)

FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 11
Safety notes
2
2.1
General safety instructions
CAUTION
Correct, reliable operation of the product requires proper transport, storage, positioning and
assembly as well as careful operation and maintenance. Only qualified personnel should
install or operate this instrument.
Note
Alterations to the product, including opening or improper repairs of the product, are not
permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.

Safety notes
2.2 Warning Symbols
FUE1010 IP65 NEMA 4X
12 Operating Instructions, 12/2014, A5E03086491-AC
2.2
Warning Symbols
Symbol
Explanation
Consult operating instructions
Hot surface
Dangerous electrical voltage
Corrosive materials
Toxic materials
Isolate the device from power using a circuit-breaker
Protect the device from impact otherwise loss of degree of protection
Protective insulation; device in protection class II

Safety notes
2.3 Laws and directives
FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 13
2.3
Laws and directives
General requirements
Installation of the equipment must comply with national regulations. For example, the
National Electrical Codes.
Instrument safety standards
The device has been tested at the factory, based on the safety requirements. In order to
maintain this condition over the expected life of the device the requirements described in
these Operating Instructions must be observed.
NOTICE
Material compatibility
Siemens can provide assistance with the selection of sensor parts. However, the full
responsibility for the selection rests with the customer and Siemens can take no
responsibility for any failure due to material incompatibility.
CE marked equipment
The CE-mark symbolizes the compliance of the device with the following Directives:
●EMC-Directive 2004/108/EC
●Low voltage Directive 2006/95/EC
●ATEX Directive 94/9/EC

Safety notes
2.4 Lithium batteries
FUE1010 IP65 NEMA 4X
14 Operating Instructions, 12/2014, A5E03086491-AC
2.4
Lithium batteries
Lithium batteries are primary power sources with high energy content designed to represent
the highest possible degree of safety.
WARNING
Potential hazard
Lithium batteries may present a potential hazard if they are abused electrically or
mechanically. This is in most circumstances associated with the generation of excessive
heat where internal pressure may cause the cell to rupture.
Thus the following basic precautions should be observed when handling and using lithium
batteries:
•Do not short-circuit, recharge or connect with false polarity.
•Do not expose to temperature beyond the specified temperature range or incinerate the
battery.
•Do not crush, puncture or open cells or disassemble battery packs.
•Do not weld or solder to the battery’s body.
•Do not expose contents to water.
2.5
Installation in hazardous area
WARNING
Explosion Hazard
Equipment used in hazardous areas must be Ex-approved and marked accordingly.
It is required that the special conditions for safe use provided in the manual and in the Ex
certificate are followed!

Safety notes
2.5 Installation in hazardous area
FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 15
Hazardous area approvals
The device is approved for use in hazardous area and has the following approval:
●FM and CSA certified
- Class I, Division 1, Groups ABCD
- Class II, Division 1, Groups EFG
●ATEX
WARNING
Explosion Hazard
Devices without the correct hazardous area approval create dangerous environments.
Make sure the hazardous area approval is suitable for the environment in which the
device will be installed.
Intrinsically safe data
WARNING
Explosion Hazard
User must install unit with Siemens drawings. With intrinsically safe circuits, use only
certified meters appropriate for the transmitter.
If a non-conforming supply unit is used, the "fail-safe" type of protection will no longer be
effective and the approval certification will be invalid.
Hazardous area safety requirements
It is required that:
●Electrical connections are in accordance with EN60079-14 (Installing Electrical Systems
in Explosion Hazardous Areas).
●The protective cover over the power supply is properly installed. For intrinsically safe
circuits the connection area can be opened.
●Appropriate cable connectors are used for the output circuits:
–Intrinsically safe: blue
–Non-intrinsically safe: black

Safety notes
2.5 Installation in hazardous area
FUE1010 IP65 NEMA 4X
16 Operating Instructions, 12/2014, A5E03086491-AC
●Sensor and transmitter are connected to the potential equalization.
For intrinsically safe output circuits potential equalization must be maintained along the
entire connection path.
●When protective earth (PE) is connected, no potential difference between the protective
earth (PE) and the potential equalization (PA) can exist, even during a fault condition.
WARNING
Explosion Hazard
"Flameproof enclosure" type of protection
Only open devices with type of protection "Flameproof enclosure" (e.g. FUT1010 NEMA
7) in hazardous areas when the power to the device is turned off, otherwise there is a
risk of explosion.
WARNING
Explosion Hazard
Laying Cables
Cable for use in zone 1 and 2 must satisfy the requirements for having a proof voltage <
AC 500 V applied between the conductor/ground, conductor/shield and shield/ground.
Connect the devices that are operated in hazardous areas as per the stipulations
applicable in the country of operation, e.g. for Ex "d" and "nA", permanent cables must
be laid.
WARNING
Explosion Hazard
Devices with the common approval "Intrinsically safe" and "Flameproof"
The following is applicable for devices with the common approval "Intrinsically safe" and
"Flameproof" (Ex ia + Ex d): Before commissioning, make sure that the type of
protection that is not suitable is permanently defaced on the nameplate to avoid
improper use.
If a non-conforming infeed is used, the "fail-safe" type of protection will no longer be
effective.

Safety notes
2.6 Safety Notes
FUE1010 IP65 NEMA 4X
Operating Instructions, 12/2014, A5E03086491-AC 17
2.6
Safety Notes
Safety Information for Hazardous Areas
DANGER
Explosion Hazard
Will Cause Death, Serious Injury or Property Damage.
Restrict use and repair to qualified personnel.
DANGER
Explosion Hazard
Death or severe personal injury and/or equipment and property damage will result if proper
Hazardous (Classified) Locations installation precautions are not taken.
Restrict use and repair to qualified personnel.
DANGER
Explosion Hazard
The use of unauthorized parts in the repair of the equipment, tampering by unqualified
personnel, or operation with the cover open in a Hazardous (Classified) Location will result
in dangerous conditions which will cause death, serious injury, and/or equipment and
property damage.
Restrict use and repair to qualified personnel.
Follow all safety instructions contained or referenced herein.
DANGER
Explosion Hazard
Death or severe personal injury and/or equipment and property damage will result due to
improper installation or use of this equipment when located in a Hazardous (Classified)
Location.
•Install as directed.
•Disconnect power source before servicing.
•Keep cover closed when equipment is operating.

Safety notes
2.6 Safety Notes
FUE1010 IP65 NEMA 4X
18 Operating Instructions, 12/2014, A5E03086491-AC
WARNING
Qualified personnel
This flowmeter system may only be set up and used in conjunction with this document and
the instructions on the electronic media provided. Installation, maintenance and operation
of the flowmeter system may only be performed by qualified personnel. Within the context
of this Document, qualified persons are defined as persons who have the skills and
knowledge related to the construction and operation of the electrical equipment and
installations and have received safety training to recognize and avoid the potentially
explosive hazards involved.
Qualified personnel possess the following qualifications
1. Is trained and authorized to energize, de-energize, clear, ground and tag circuits and
equipment in accordance with established safety practices.
2. Is trained in the proper care and use of protective equipment such as rubber gloves,
hard hat, safety glasses or face shields, flash clothing, etc., in accordance with
established safety practices.
3. Is trained in rendering first aid.
Note
This document does not purport to cover all details or variations in equipment, or to provide
for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired
or should particular problems arise,
which are not covered sufficiently for the purchaser's purposes, the matter should be
referred to the local Siemens sales office (www.automation.siemens.com/partner). The
contents of this Document shall not become part
of or modify any prior or existing
agreement, commitment or relationship. The sales contract contains the entire obligation of
Siemens. The warranty contained in the contact between the parties is the sole warranty of
Siemens. Any statements contained her
ein do not create new warranties or modify the
existing warranty.
Safety Information for Hazardous Areas
Note
Ratings under this heading apply to specific model families.
Check Your Model Number: FUE1010, 7ME3500
FM-CSA installation
Read, understand and follow all safety instructions on the electronic media provided. This
equipment is rated for use in hazardous (classified) locations as stated below and must be
installed according to the 1010-304 installation drawing provided on the media. Failure to
install the equipment in the prescribed manner will result in unsafe operation. Follow all local
jurisdictional safety codes when operating this equipment. When properly installed the
equipment meets the following FM – CSA ratings.