Siemens SINAMICS G110M User manual

SINAMICS G110M Getting Started
___________________
___________________
___________________
___________________
___________________
SINAMICS
SINAMICS G110M
SINAMICS G110M Getting Started
Getting Started
Edition 09/2014, Firmware V4.7
09/2014, FW V4.7
A5E31298643B AC
Safety instructions
1
Description
2
Installation
3
Commissioning
4
Troubleshooting
5

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E31298643B AC
Ⓟ
09/2014 Subject to change
Copyright © Siemens AG 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SINAMICS G110M Getting Started
Getting Started, 09/2014, FW V4.7, A5E31298643B AC 5
Table of contents
1 Safety instructions................................................................................................................................... 7
1.1 General safety instructions .......................................................................................................7
1.2 Safety instructions for electromagnetic fields (EMF) ..............................................................10
1.3 Handling electrostatic sensitive devices (ESD) ......................................................................10
1.4 Industrial security ....................................................................................................................11
1.5 Residual risks of power drive systems....................................................................................12
2 Description............................................................................................................................................ 15
2.1 Identifying the components of the system ..............................................................................15
2.2 SINAMICS G110M converter..................................................................................................16
2.3 General layout SINAMICS G110M system.............................................................................23
3 Installation ............................................................................................................................................ 27
3.1 Mechanical Installation............................................................................................................28
3.1.1 Dimensions of converters and motors ....................................................................................28
3.2 System Installation..................................................................................................................31
3.2.1 Installation Procedures ...........................................................................................................31
3.2.2 Grounding the terminal housing..............................................................................................45
3.2.3 Installing the 24V power supply ..............................................................................................46
3.3 Electrical Installation ...............................................................................................................49
3.3.1 SINAMICS G110M Electrical data ..........................................................................................49
3.3.2 Connections and interference suppression ............................................................................51
3.3.3 Basic EMC rules .....................................................................................................................52
3.3.4 Connection and cables ...........................................................................................................53
3.3.5 Cable protection......................................................................................................................61
4 Commissioning ..................................................................................................................................... 63
4.1 Commissioning tools...............................................................................................................63
4.2 Wiring example for the factory settings...................................................................................64
4.3 Factory setting of the inverter control .....................................................................................66
4.4 V/f control or speed control.....................................................................................................67
4.5 p0015 Macros .........................................................................................................................68
4.6 Basic Commissioning with DIP switches ................................................................................70
4.7 Basic commissioning with IOP................................................................................................75
4.8 Basic commissioning with STARTER .....................................................................................79
4.8.1 Adapting the USB interface ....................................................................................................79
4.8.2 Generating a STARTER project .............................................................................................81
4.8.3 Go online and start wizard for basic commissioning ..............................................................82

Table of contents
SINAMICS G110M Getting Started
6Getting Started, 09/2014, FW V4.7, A5E31298643B AC
4.8.4 Identifying motor data ............................................................................................................ 84
4.8.5 Change settings ..................................................................................................................... 85
4.8.6 Optimize the drive using the trace function............................................................................ 87
5 Troubleshooting .................................................................................................................................... 91
5.1 Status LED overview.............................................................................................................. 91

SINAMICS G110M Getting Started
Getting Started, 09/2014, FW V4.7, A5E31298643B AC 7
Safety instructions
1
1.1
General safety instructions
DANGER
Danger to life due to live parts and other energy sources
Death or serious injury can result when live parts are touched.
•Only work on electrical devices when you are qualified for this job.
•Always observe the country-specific safety rules.
Generally, six steps apply when establishing safety:
1. Prepare for shutdown and notify all those who will be affected by the procedure.
2. Disconnect the machine from the supply.
–Switch off the machine.
–Wait until the discharge time specified on the warning labels has elapsed.
–Check that it really is in a no-voltage condition, from phase conductor to phase
conductor and phase conductor to protective conductor.
–Check whether the existing auxiliary supply circuits are de-energized.
–Ensure that the motors cannot move.
3. Identify all other hazardous energy sources, e.g. compressed air, hydraulic systems,
water.
4. Isolate or neutralize all hazardous energy sources, e.g. by closing switches, grounding
or short-circuiting or closing valves.
5. Secure the energy sources against switching on again.
6. Make sure that the machine is completely locked ... and that you have the right
machine.
After you have completed the work, restore the operational readiness in the inverse
sequence.
WARNING
Danger to life through a hazardous voltage when connecting an unsuitable power supply
Death or serious injury can result when live parts are touched in the event of a fault.
•Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV-
(Protective Extra Low Voltage) output voltages for all connections and terminals of the
electronics modules.

Safety instructions
1.1 General safety instructions
SINAMICS G110M Getting Started
8Getting Started, 09/2014, FW V4.7, A5E31298643B AC
WARNING
Danger to life when live parts are touched on damaged devices
Improper handling of devices can cause damage.
Hazardous voltages can be present at the housing or exposed components on damaged
devices.
•Ensure compliance with the limit values specified in the technical data during transport,
storage and operation.
•Do not use any damaged devices.
WARNING
Danger to life through electric shock due to unconnected cable shields
Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected
cable shields.
•As a minimum, connect cable shields and the cores of power cables that are not used
(e.g. brake cores) at one end at the grounded housing potential.
WARNING
Danger to life due to electric shock when not grounded
For missing or incorrectly implemented protective conductor connection for devices with
protection class I, high voltages can be present at open, exposed parts, which when
touched, can result in death or severe injury.
•Ground the device in compliance with the applicable regulations.
WARNING
Danger to life due to electric shock when opening plug connections in operation
When opening plug connections in operation, arcs can result in severe injury or death.
•Only open plug connections when the equipment is in a no-voltage state, unless it has
been explicitly stated that they can be opened in operation.
WARNING
Danger to life due to fire spreading if housing is inadequate
Fire and smoke development can cause severe personal injury or material damage.
•Install devices without a protective housing in a metal control cabinet (or protect the
device by another equivalent measure) in such a way that contact with fire inside and
outside the device is prevented.
•Additionally, select the installation site so that an uncontrolled spreading of smoke can
be avoided in the case of a fire.
•Ensure that smoke can escape via designated paths.

Safety instructions
1.1 General safety instructions
SINAMICS G110M Getting Started
Getting Started, 09/2014, FW V4.7, A5E31298643B AC 9
WARNING
Danger to life through unexpected movement of machines when using mobile wireless
devices or mobile phones
Using mobile wireless devices or mobile phones with a transmitter power > 1 W closer than
approx. 2 m to the components may cause the devices to malfunction and influence the
functional safety of machines, therefore putting people at risk or causing material damage.
•Switch the wireless devices or mobile phones off in the immediate vicinity of the
components.
WARNING
Danger to life due to the motor catching fire in the event of insulation overload
There is a greater load on the motor insulation through a ground fault in an IT system. A
possible result is the failure of the insulation with a risk for personnel through smoke
development and fire.
•Use a monitoring device that signals an insulation fault.
•Correct the fault as quickly as possible so the motor insulation is not overloaded.
WARNING
Danger to life due to fire if overheating occurs because of insufficient ventilation clearances
Inadequate ventilation clearances can cause overheating with a risk for personnel through
smoke development and fire. This can also result in increased downtime and reduced
service lives for devices / systems.
•Ensure compliance with the specified minimum clearance as ventilation clearance for
the respective component. They can be found in the dimension drawings or in the
"Product-specific safety instructions" at the start of the respective section.
WARNING
Danger of an accident occuring due to missing or illegible warning labels
Missing or illegible warning labels can result in death or serious injury.
•Check that the warning labels are complete based on the documentation.
•Attach any missing warning labels to the components, in the national language if
necessary.
•Replace illegible warning labels.
NOTICE
Device damage caused by incorrect voltage/insulation tests
Incorrect voltage/insulation tests can damage the device.
•Before carrying out a voltage/insulation test, disconnect the system/machine.
All converters and motors are subject to a high voltage test in the manufacturer's facility. As
a consequence, it is not necessary to carry out additional tasks in the system/machine.

Safety instructions
1.2 Safety instructions for electromagnetic fields (EMF)
SINAMICS G110M Getting Started
10 Getting Started, 09/2014, FW V4.7, A5E31298643B AC
WARNING
Danger to life when safety functions are inactive
Safety functions that are inactive or that have not been adjusted accordingly can cause
operational faults on machines that could lead to serious injury or death.
•Observe the information in the appropriate product documentation before
commissioning.
•Carry out a safety inspection for functions relevant to safety on the entire system,
including all safety-related components.
•Ensure that the safety functions used in your drives and automation tasks are adjusted
and activated through appropriate parameterizing.
•Run a function test.
•Only put your plant into live operation once you have guaranteed that the functions
relevant to safety are running correctly.
Note
Important safety notices for safety functions
If you want to use safety functions, you must observe the safety notices in the safety
manuals.
1.2
Safety instructions for electromagnetic fields (EMF)
WARNING
Danger to life from electromagnetic fields
Electromagnetic fields (EMF) are generated by the operation of electrical power equipment
such as transformers, converters or motors.
People with pacemakers or implants are at a special risk in the immediate vicinity of these
devices/systems.
•If affected by this, keep a distance of at least 2 m.
1.3
Handling electrostatic sensitive devices (ESD)
Electrostatic sensitive devices (ESD) are individual components, integrated circuits, modules
or devices that may be damaged by either electric fields or electrostatic discharge.