Siemens SIMATIC S7 User manual

A26361-K877-Z100-4-5E19 English
Contents
Introduction........................................................................................................................................1
Notational conventions ..............................................................................................................2
Important notes .................................................................................................................................2
Safety........................................................................................................................................2
Cleaning notes...........................................................................................................................3
Transport notes .........................................................................................................................3
Manufacturer’s notes .................................................................................................................4
Important note on power cable ..................................................................................................4
Disposal and recycling...............................................................................................................4
Checking the contents of the consignment ........................................................................................5
Installing an ergonomic video workstation .........................................................................................5
Setting up the monitor .......................................................................................................................6
Installation/Deinstallation of the loudspeaker module ........................................................................7
Connecting the monitor......................................................................................................................7
Anti-theft protection ...........................................................................................................................8
Operation of the monitor....................................................................................................................9
Switching the monitor on/off ......................................................................................................9
Notes on power management....................................................................................................9
Changing the monitor settings .................................................................................................10
Monitor settings using the OSD menu .............................................................................................11
Removing the monitor base.....................................................................................................13
Notes on ergonomic colour adjustment............................................................................................14
Technical data.................................................................................................................................14
VESA-DDC-compatible VGA interface.....................................................................................15
Preset operating modes...........................................................................................................16
Power supply plug ...................................................................................................................16
D-SUB connector.....................................................................................................................17
Trouble shooting..............................................................................................................................17
FCC Class B Compliance Statement.......................................................................................18
Declaration of Conformity ........................................................................................................19

A26361-K877-Z100-4-5E19 English - 1
Introduction
Your new LCD (Liquid Crystal Display) monitor S7 offers numerous features and functions, for
example:
•TFT display (Thin Film Transistor; active matrix)
•minimal space requirements thanks to slim casing
•optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour
purity right into the corners)
•high degree of brightness and good contrast
•high resolution (1280x1024) for displaying the information content of a conventional 19-inch
screen with CRT (Cathode Ray Tube)
•presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)
•automatic scanning of all horizontal frequencies from 31 to 80 kHz and all refresh rates (vertical
frequencies) from 60 to 75 Hz (all absolutely flicker-free)
•digital screen controller with microprocessor for storing 19 different display modes
•freely adjustable colour alignment for matching the screen colours to the colours of various
input and output devices
•convenient operation via integrated OSD (On-Screen-Display) menu
•VESA-DDC compatibility
•VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface, mechanical
interface to swivel arm and wall bracket)
•plug&play capability
•power management for reducing power consumption when the computer system is not in use
•compliance with the recommendations in accordance with TCO ’99
In normal screen mode (dark characters against a light background) the monitor satisfies the
ergonomic requirements for the GS symbol.
This Operating Manual contains important information you require to start up and run your LCD
monitor.
A screen controller with VGA interface is required to control the S7 LCD monitor. The monitor
processes the data supplied to it by the screen controller. The screen controller/the associated
driver software is responsible for setting the modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs (see the
"Changing the monitor settings" section in the "Operation of the monitor" chapter).
Target group
You don't need to be an "expert" to perform the operations described here. Do, however, read the
chapter "Important notes" in the Operating Manual of the computer and in this Operating Manual.
In the event of any problems occurring, please contact your sales outlet or our Help Desk.
Further information
Details of how you set the resolution and refresh rate are provided in the documentation on your
screen controller/the associated driver software.

Colour monitor S7
2 - English A26361-K877-Z100-4-5E19
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
!Pay particular attention to text marked with this symbol. Failure to observe this warning
endangers your life, destroys the device, or may lead to loss of data.
i
Supplementary information, remarks, and tips follow this symbol.
ÊText which follows this symbol describes activities that must be performed in the order shown.
"Quotation marks" indicate names of chapters or terms.
Important notes
!In this chapter you will find information regarding safety which is essential to take note of
with your monitor.
Safety
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales outlet or our Help Desk.
•The display surface of the LCD monitor is sensitive to pressure and scratches. You should
therefore be careful with the display surface so as to avoid lasting damage (Newton rings,
scratches).
•If the device is brought into the installation site from a cold environment, condensation can
form. Before operating the device, wait until it is absolutely dry and has reached approximately
the same temperature as the installation site.
•During installation and before operating the device, please observe the instructions on
environmental conditions in the "Technical data" chapter as well as the instructions in the
"Installing an ergonomic video workstation" chapter.
•Ensure that the monitor is sufficiently ventilated. The monitor may only be operated with the
monitor base, swivel arm or wall bracket.
•The power adapter automatically sets itself to a mains voltage in the range of 100 V to 240 V.
Ensure that the local mains voltage lies within these limits.
•Ensure that the power socket on the power adapter or the grounded mains outlet is freely
accessible.
•The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.
•Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the chapter "Connecting the monitor".
•No data transmission cable should be connected or disconnected during a thunderstorm.
•Please ensure that no objects (e.g. necklaces, paperclips etc.) or liquids can get into the
interior of the device (this may cause an electrical shock or short circuit).

Colour monitor S7
A26361-K877-Z100-4-5E19 English - 3
•In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our Help
Desk.
•The screen background lighting contains mercury. You must observe the applicable handling
and disposal safety regulations for fluorescent tubes.
•Only qualified technicians should repair the device. Unauthorised opening and incorrect repair
may greatly endanger the user (electric shock, fire risk).
•You may set only those resolutions and refresh rates specified in the "Technical data" chapter.
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or
our Help Desk.
•Keep this operating manual together with your device. If you pass on the device to third parties,
you should include this manual.
Cleaning notes
•Always pull out the power plug before you clean the monitor.
•Do not clean any interior parts yourself, leave this job to a service technician.
•Do not use any cleaning agents that contain abrasives or may corrode plastic.
•Ensure that no liquid will run into the system.
•Ensure that the ventilation areas of the monitor are free.
•The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only
using a soft, slightly moistened cloth.
Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.
Transport notes
•Transport the monitor with care and only in its original packaging or another corresponding
packaging fit to protect it against knocks and jolts.
•Never drop the LCD monitor (danger of glass breakage).

Colour monitor S7
4 - English A26361-K877-Z100-4-5E19
Manufacturer’s notes
Energy Star
The Fujitsu Siemens LCD colour monitor S7 is designed to conserve
electricity by dropping to less than 4,5 W when it goes into standby,
suspend and OFF mode. With this new power management the S7
qualifies for the U.S. Environmental Protection Agency's (EPA) Energy
Star Computers award.
The EPA estimates that computer equipment uses 5% percent of all business electricity and that
this is growing rapidly. If all desktop computers and peripherals enter a low-power mode when not in
use, the overall savings in electricity could amount to $ 2 thousand million annually. These savings
could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere - the
equivalent of 5 million automobiles.
As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product
meets the Energy Star guidelines for energy efficiency.
CE marking
The shipped version of this device complies with the requirements of the EEC
directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage
directive".
Important note on power cable
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary
to replace the original cable set.
•The female/male receptacles of the cord set must meet CEE-22 requirements.
•The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath or on the insulation of one of the inner conductors.
•For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
For devices which sit on the floor, only SJT type cable sets may be used.
•The cable set must be selected according to the rated current for your device.
Disposal and recycling
This device has been manufactured to the highest possible degree from materials which can be
recycled or disposed of in a manner that is not environmentally damaging.
The device may be taken back after use to be recycled, provided that it is returned in a condition
that is the result of normal use. Any components not reclaimed will be disposed of in an
environmentally acceptable manner.
If you have any questions on disposal, please contact your local office, our Help Desk, or:
Fujitsu Siemens Computers GmbH
Recyclingcenter
D-33106 Paderborn
Tel.: ++ 49 5251 - 818 010/ Fax: ++ 49 5251 - 818 015

Colour monitor S7
A26361-K877-Z100-4-5E19 English - 5
Checking the contents of the consignment
ÊUnpack all the individual parts.
ÊCheck the delivery for damage incurred during transportation.
ÊCheck whether the delivery agrees with the details in the delivery note.
The complete LCD monitor package includes:
−one monitor
−one data cable
−one power cable
−one audio cable
−a power adapter with power adapter cable
−one floppy disk
−one Warranty Booklet
−this Operating Manual
Should you discover that the delivery does not correspond to the delivery note, notify your local
sales outlet immediately.
i
It is recommended not to throw away the original packaging material. Keep it for future
transportation.
Installing an ergonomic video workstation
Before you set up your equipment, you should select a suitable position for working at the monitor.
Please observe the following advice when installing a video workstation.
Window
permissible
reaching sector
600 mm
edge of desk
permissible
reaching sector
600 mm
Avoid direct and reflected glare. Avoid glare from electric
lighting. Position the keyboard where it is easiest to reach.

Colour monitor S7
6 - English A26361-K877-Z100-4-5E19
30°
30°
65°
65°
0°
60°
preferable viewing sector
permissible viewing sector
permissible
viewing sector
approx. 90°
and
more
approx. 90°
Position the monitor for
optimum viewing. The viewing
distance to the monitor should
be approximately 50 cm.
Keep ventilated areas clear. Remember to maintain correct
posture.
The typical monitor base allows you to adjust the tilt of the display by 4°forward and by 30°back.
Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available
from specialised dealers, may be advisable. For this purpose the monitor base must be removed
(see chapter "Removing the monitor base").
Setting up the monitor
Your monitor is folded in its packing carton in
order to save space.
ÊLay the monitor on its face on a soft
surface.
The monitor surface is susceptible to scratching!
ÊFold out the monitor base.
ÊSlide the latch on the base to the middle
position and engage the monitor base.
ÊPlace the monitor in an upright position.

Colour monitor S7
A26361-K877-Z100-4-5E19 English - 7
Installation/Deinstallation of the loudspeaker module
Installation
ÊAlign the loudspeaker module that the two
hooks slot into the two openings on the
bottom of the monitor.
ÊEngage the loudspeaker module
Deinstallation
ÊPress the two push-buttons on the rear of
the loudspeaker module and remove it
downward.
Connecting the monitor
Information on the computer connections and interfaces is contained in the operating manual for
your computer.
!Observe the "Safety" in the chapter "Important notes" in this operating manual.
The thermal dissipation on the rear wall of the casing must not be prevented by shielding.
Therefore, make sure that the distance to the wall or pieces of furniture is long enough.
13
24
1 = Connector for the power supply
2 = D-SUB connector
3 = Audio IN
4 = Audio IN
ÊBe sure that the monitor and the computer are switched off.
!The computer power plug must be pulled out!

Colour monitor S7
8 - English A26361-K877-Z100-4-5E19
ÊConnect the angled connector of the data cable to the D-SUB connector on the monitor (2) and
secure the plug-in connection by tightening the safety screws.
ÊConnect the even connector of the data cable to the active monitor port on the computer and
secure the plug-in connection by tightening the safety screws.
i
If your computer has two monitor ports ("onboard" screen controller and separate
graphics card), the monitor port for the separate graphics card is usually active.
ÊInsert the two cinch connector of the audio line in the two AUDIO IN (3 and 4) sockets on the
monitor and make sure it is properly engaged.
ÊInsert the stereo jack plug of the audio line in the audio output of the computer.
ÊPlug the power adapter cable into the power connector (1) of the monitor.
ÊFirmly insert the socket with the power cable supplied into the power cable connection of the
power adapter and check whether the socket is securely seated.
ÊConnect the plug on the power cable supplied into a properly grounded mains outlet.
ÊPlug the power connector of the computer into a properly grounded mains outlet.
i
When you start working with your monitor for the first time you should install the
appropriate graphics drivers for your application software. Details of how to do this are
provided in the documentation on your screen controller/the associated driver software.
Anti-theft protection
A lock (Kensington Lock) can be mounted in the security slot to protect the monitor from theft.
i
A Kensington Lock is not included in the consignment of the monitor.