Siemens SITOP PSU100S User manual
SITOP PSU100S
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SITOP power supply
SITOP PSU100S
Operating Instructions
SITOP PSU100S 24 V/2.5 A
6EP1332-2BA20
SITOP PSU100S 24 V/5 A
6EP1333-2BA20
SITOP PSU100S 24 V/10 A
6EP1334-2BA20
SITOP PSU100S 24 V/20 A
6EP1336-2BA10
SITOP PSU100S 12 V/7 A
6EP1322-2BA00
SITOP PSU100S 12 V/14 A
6EP1323-2BA00
02.2013
C98130-A7589-A1-3-7629
Overview
Safety instructions
1
Description, device design,
dimension drawing
2
Mounting/removal
3
Mounting position, mounting
clearances
4
Installation
5
Technical data
6
Safety, approvals, EMC
7
Ambient conditions
8
Applications
9
Environment
10
Service & Support
11
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
C98130-A7589-A1-3-7629
Ⓟ 03/2013 Technical data subject to change
Copyright © Siemens AG 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 3
Overview
Description
The 1-phase SITOP PSU100S from the SITOP smart product line is a powerful, regulated
standard power supply for automated machines and systems. In addition to a high efficiency,
these low-profile power supply units have an outstanding overload behavior.
The key benefits of the product include:
● Wide-range input, which allows them to be connected to almost any 1-phase line supply
around the world
● Output voltage can be adjusted in the range 22.2 (24)...28 V or 11.5…15.5 V
● Brief overload capability of 150% for 5 s/min (extra power)
● Continuous overload capability of 120% up to an ambient temperature of +45° C
● Integrated signaling contact for "24 V OK" or "12 V OK"
● Ambient temperature -10 (0)...+70 °C
● To increase the system availability, these reliable power supplies can be expanded using
SITOP supplementary modules (redundancy module, selectivity module, buffer module),
as well as SITOP DC-UPS modules.
Overview
SITOP PSU100S
4 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
Ordering data
The following device options are available:
Regulated SITOP PSU100S power supply
Type Order number
1-phase 120/230 V AC input,
24 V/2.5 A DC output
6EP1332-2BA20
1-phase 120/230 V AC input,
24 V/5 A DC output
6EP1333-2BA20
1-phase 120/230 V AC input,
24 V/10 A DC output
6EP1334-2BA20
1-phase 120/230 V AC input,
24 V/20 A DC output
6EP1336-2BA10
1-phase 120/230 V AC input,
12 V/7 A DC output
6EP1322-2BA00
1-phase 120/230 V AC input,
12 V/14 A DC output
6EP1323-2BA00
Accessories
Item Order number
Device identification labels 10 mm × 7 mm, pastel turquoise 3RT1900-1SB10
Device identification labels 20 mm × 7 mm, pastel turquoise 3RT1900-1SB20
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 5
Table of contents
Overview.................................................................................................................................................... 3
1 Safety instructions ..................................................................................................................................... 7
2 Description, device design, dimension drawing ......................................................................................... 9
2.1 Device description..........................................................................................................................9
2.2 Connections and terminal designation.........................................................................................10
2.3 Potentiometer...............................................................................................................................11
2.4 Status displays and signaling.......................................................................................................12
2.5 Block diagram ..............................................................................................................................13
2.6 Dimensions and weight................................................................................................................14
3 Mounting/removal .................................................................................................................................... 17
4 Mounting position, mounting clearances.................................................................................................. 19
4.1 Standard mounting position .........................................................................................................19
4.2 Other mounting positions .............................................................................................................22
4.2.1 6EP1332-2BA20 ..........................................................................................................................22
4.2.2 6EP1333-2BA20 ..........................................................................................................................24
4.2.3 6EP1334-2BA20 ..........................................................................................................................26
4.2.4 6EP1336-2BA10 ..........................................................................................................................28
4.2.5 6EP1322-2BA00 ..........................................................................................................................30
4.2.6 6EP1323-2BA00 ..........................................................................................................................32
5 Installation ............................................................................................................................................... 35
5.1 Line-side connection ....................................................................................................................35
5.2 Output-side connection................................................................................................................37
6 Technical data ......................................................................................................................................... 39
6.1 Input .............................................................................................................................................39
6.2 Output ..........................................................................................................................................41
6.3 Efficiency......................................................................................................................................47
6.4 Closed-loop control ......................................................................................................................50
6.5 Protection and monitoring............................................................................................................51
6.6 MTBF ...........................................................................................................................................51
6.7 Mechanical system ......................................................................................................................52
6.8 Dimension drawing ......................................................................................................................53
7 Safety, approvals, EMC ........................................................................................................................... 55
7.1 Safety ...........................................................................................................................................55
Table of contents
SITOP PSU100S
6 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
7.2 Test voltage................................................................................................................................. 56
7.3 Approvals .................................................................................................................................... 57
7.4 EMC ............................................................................................................................................ 58
8 Ambient conditions .................................................................................................................................. 59
9 Applications ............................................................................................................................................. 61
9.1 Parallel connection to increase power rating .............................................................................. 61
9.2 Parallel connection for redundancy............................................................................................. 62
9.3 Series connection for increased voltage ..................................................................................... 63
9.4 Overload protection in the 24 V output circuit.............................................................................64
9.5 Protection against short-time voltage dips.................................................................................. 65
9.6 Protecting against longer power failures..................................................................................... 66
10 Environment ............................................................................................................................................ 69
11 Service & Support.................................................................................................................................... 71
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 7
Safety instructions 1
WARNING
Correct handling of the devices
When operating electrical devices, it is inevitable that certain components will carry
dangerous voltages.
Therefore, failure to handle the units properly can result in death or serious physical injury
as well as extensive property damage.
Only appropriately qualified personnel may work on or in the vicinity of this equipment.
Perfect, safe, and reliable operation of this equipment is dependent on proper
transportation, storage, installation and mounting.
Before installation or maintenance work can begin, the system's main switch must be
switched off and measures taken to prevent it being switched on again.
If this instruction is not observed, touching live parts can result in death or serious injury.
Safety instructions
SITOP PSU100S
8 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 9
Description, device design, dimension drawing 2
2.1 Device description
SITOP PSU100S is a primary-clocked power supply for connection to a 1-phase AC line
supply. An electronically regulated DC voltage that can be set via a potentiometer is
available at the output of the device. The output of the device is isolated, no-load proof and
short-circuit proof. The LED display indicates the operating status. The operating state of the
device can be processed via the signaling contact.
① Line input
② DC output
③ Signaling contacts
④ Potentiometer 22.2…28 / 24...28 V / 11.5…15.5 V
⑤ Indicator light (output voltage OK)
⑥ DIN rail slider
⑦ Natural convection
⑧ Clearance above/below
Figure 2-1 Design
Description, device design, dimension drawing
2.2 Connections and terminal designation
SITOP PSU100S
10 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
2.2 Connections and terminal designation
The line input terminals ① can be used to establish the connection to supply voltage. The
output terminals ② are used to connect to the loads to be supplied (see also Section
Installation (Page 35)).
The operating state of the device can be processed via the signaling contact ③ (function
and contact rating, see Chapter Status displays and signaling (Page 12)).
Connections and terminal designations
① Line input L1, N, PE One screw terminal each
② Output + 2 screw terminals
② Output – 2 screw terminals
③ signal 13, 14 One screw terminal each
$:*
1P
6=6[3=3+
[PP
[PP
1P
PP
6=6[3=3+
PD[ෘPP
1P
Figure 2-2 Terminal data for 6EP1332-2BA20, 6EP1333-2BA20, 6EP1334-2BA20, 6EP1322-
2BA00, 6EP1323-2BA00
$:*
1P
6=6[3=3+
6=6[ 6=6[3=3+
PD[ෘPP
[PP
[PP
[PP
[PP
1P
1P 1P
PP PP
Figure 2-3 Terminal data for 6EP1336-2BA10
Description, device design, dimension drawing
2.3 Potentiometer
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 11
2.3 Potentiometer
The potentiometer ④ on the front of the device is used to adjust the output voltage. The
output voltage is set to the rated value at the factory and can be set within certain limits; for
example, to compensate voltage drops across long supply lines to the connected load.
(3%$H[DPSOH
(3%$(3%$
(3%$(3%$
(3%$
Figure 2-4 Potentiometer
Type Factory setting Adjustment range
6EP1322-2BA00
6EP1323-2BA00
12 V 11.5...15.5 V
6EP1332-2BA20
6EP1333-2BA20
6EP1334-2BA20
24 V 22.2.…28 V
6EP1336-2BA10 24 V 24.…28 V
NOTICE
Thermal overload possible
When setting the output voltage to higher than the rated voltage, the output current must be
derated, or the permissible ambient temperature must be taken into consideration.
Note
It is only permissible to use an insulated screwdriver when actuating the potentiometer.
For notes on actuating the potentiometer (screwdriver, torque), refer to Figure 2-2 Terminal
data for 6EP1332-2BA20, 6EP1333-2BA20, 6EP1334-2BA20, 6EP1322-2BA00, 6EP1323-
2BA00 (Page 10) and Figure 2-3 Terminal data for 6EP1336-2BA10 (Page 10).
Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU100S
12 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
2.4 Status displays and signaling
6EP1322-2BA00, 6EP1323-2BA00, 6EP1332-2BA20
6EP1333-2BA20, 6EP1334-2BA20, 6EP1336-2BA10
Status display LED green for 24 V O.K. or 12 V O.K.
Signaling contact Relay contact (NO contact, contact rating 30 V AC / 0.5 A, 60 V DC / 0.3 A, 30 V DC / 1 A)
for 24 V O.K. or 12 V O.K.
(3%$H[DPSOH
(3%$(3%$
(3%$(3%$
(3%$
Figure 2-5 Status displays and signaling
Signaling 6EP1322-2BA00
6EP1323-2BA00
6EP1332-2BA20
6EP1333-2BA20
6EP1334-2BA20
6EP1336-2BA10
LED ⑤ lights up green
Signaling contact ③,
contacts 13-14 closed
Normal operation,
Output voltage
>10 V ±0.5 V
Normal operation,
Output voltage
>20 V ±0.5 V
Normal operation,
Output voltage
>20 V ±0.5 V
LED ⑤ dark
Signaling contact ③,
contacts 13-14 open
(inactive position)
Overload operation or power
supply voltage missing
Overload operation or power
supply voltage missing
Overload / hiccup operation,
power supply missing or the
device has tripped due to
overtemperature (reset
possible with power OFF for
approx. 30 min)
Description, device design, dimension drawing
2.5 Block diagram
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 13
2.5 Block diagram
7UDQVIRUPHU
3RZHU
WUDQVLVWRUV
3:0FRQWUROOHU 9ROWDJHFRQWUROOHU
2YHUYROWDJH
SURWHFWLRQ
7HPSHUDWXUH
PRQLWRULQJ
8VHU,QWHUIDFH
0RQLWRULQJFLUFXLW
7HPSHUDWXUH
2YHUYROWDJH
3XOVHZLGWKOLPLWLQJ
,QSXWWHUPLQDO$&
,QUXVKFXUUHQW
OLPLWHU
5HFWLILHU
)LOWHU
5HFWLILHU
6HFRQGDU\
2XWSXWILOWHU
2XWSXWWHUPLQDO'&
0LFURFRQWUROOHU
%HKDYLRUZLWKUHVSHFWWRWLPH
([WUD3RZHU
2XWSXWFXUUHQWOLPLWLQJDVD
IXQFWLRQRIWKHWHPSHUDWXUH
'ULYHUV
2QO\IRU(3%$
92.
92.
92.
92.
$'-867
9
9
9
Figure 2-6 Block diagram
Description, device design, dimension drawing
2.6 Dimensions and weight
SITOP PSU100S
14 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
2.6 Dimensions and weight
120
126,5
32,5
125
79,8
Figure 2-7 Dimension drawing 6EP1332-2BA20
120
126,5
125
79,8
50
Figure 2-8 Dimension drawing 6EP1333-2BA20, 6EP1322-2BA00
Description, device design, dimension drawing
2.6 Dimensions and weight
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 15
120
126,5
125
79,8
70
Figure 2-9 Dimension drawing 6EP1334-2BA20, 6EP1323-2BA00
Figure 2-10 Dimension drawing 6EP1336-2BA10
6EP1332-2BA20 6EP1333-2BA20
6EP1322-2BA00
6EP1334-2BA20
6EP1323-2BA00
6EP1336-2BA10
Dimensions (W × H ×
D) in mm
32.5 × 125 × 120 50 × 125 × 120 70 × 125 × 120 115 × 145 × 150
Weight Approx. 0.3 kg Approx. 0.4 kg Approx. 0.7 kg Approx. 2.4 kg
Description, device design, dimension drawing
2.6 Dimensions and weight
SITOP PSU100S
16 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 17
Mounting/removal 3
WARNING
Installing the device in a housing or a control cabinet
SITOP PSU100S power supplies are built-in units. They must be installed in a housing or
control cabinet where only qualified personnel have access.
The device can be snapped onto a standard mounting rail EN 60715 35×7.5/15 for
installation in a control cabinet.
Mounting
To mount the device, position it with the mounting rail guide at the upper edge of the
standard mounting rail and press down to lock it into place. If this is too difficult, press slider
⑥ at the same time, as described under "Removal".
Removal
To remove, pull up the slider ⑥ using a screwdriver and disengage the device at the bottom
edge of the standard mounting rail (see Removal diagram (Page 17)). Then you can remove
the device from the upper edge of the standard mounting rail.
Figure 3-1 Removal
Mounting/removal
SITOP PSU100S
18 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
WARNING
Use in hazardous zones
If the device is to be used in a hazardous zone (Ex II 3G Ex nA nC IIC T4 Gc) it must be
installed in a distributor box with degree of protection IP54 or higher.
SITOP PSU100S
Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 19
Mounting position, mounting clearances 4
4.1 Standard mounting position
The device is designed for installation on standard EN 60715 35×7.5/15 mounting rails. The
device must be mounted vertically to ensure proper cooling, and with the input terminals and
output terminals at the bottom.
A clearance of at least 50 mm should be maintained above and below the device (maximum
depth of the cable duct, 50 mm).
No space is required at the side.
Output current as a function of the ambient temperature and mounting height
SITOP PSU100S
IN
OUT
70
2,0
0
2,5
1,0
0,5
1,5
020 40 60
10 30 50
3,0
120 V 230 V=
2XWSXWFXUUHQW>$@
7HPSHUDWXUH>r&@
Figure 4-1 6EP1332-2BA20: Output current in the standard mounting position
70
4
0
5
2
1
3
020 40 60
10 30 50
6
120 V 230 V
SITOP PSU100S
IN
OUT
2XWSXWFXUUHQW>$@
7HPSHUDWXUH>r&@
Figure 4-2 6EP1333-2BA20: Output current in the standard mounting position
Mounting position, mounting clearances
4.1 Standard mounting position
SITOP PSU100S
20 Operating Instructions, 02.2013, C98130-A7589-A1-3-7629
SITOP PSU100S
IN
OUT
70
8
0
10
4
2
6
020 40 60
10 30 50
12
120 V 230 V
2XWSXWFXUUHQW>$@
7HPSHUDWXUH>r&@
Figure 4-3 6EP1334-2BA20: Output current in the standard mounting position
70
16
0
20
8
4
12
020 40 60
10 30 50
24
120 V 230 V
OUT
SITOP PSU100S
IN
2XWSXWFXUUHQW>$@
7HPSHUDWXUH>r&@
Figure 4-4 6EP1336-2BA10: Output current in the standard mounting position
SITOP PSU100S
IN
OUT
70
0
020 40 60
10 30 50
120 V 230 V
4
5
2
1
3
6
7
8
2XWSXWFXUUHQW>$@
7HPSHUDWXUH>r&@
Figure 4-5 6EP1322-2BA00: Output current in the standard mounting position
Table of contents
Other Siemens Power Supply manuals
Siemens
Siemens SITOP PSU8600 User manual
Siemens
Siemens PR4018-05 User manual
Siemens
Siemens SITOP SEL1200 User manual
Siemens
Siemens SITOP C98130-A1251-A1-02-19 User manual
Siemens
Siemens PSC-12 User manual
Siemens
Siemens MICROMASTER 440 User manual
Siemens
Siemens SIMATIC NET PS598-1 Administrator guide
Siemens
Siemens VNT-PS User manual
Siemens
Siemens MPS-12-220 User manual
Siemens
Siemens SITOP PSU100L 6EP1332-1LB00 User manual
Siemens
Siemens MPS-12 User manual
Siemens
Siemens 7XV5810-0BA00 User manual
Siemens
Siemens 4AV2106-2EB00-0A User manual
Siemens
Siemens SAP 20 User manual
Siemens
Siemens SITOP PSU2600 3ph User manual
Siemens
Siemens SITOP PSU8600 Parts list manual
Siemens
Siemens 4AV2302-2EB00-0A User manual
Siemens
Siemens SITOP Power 20 6EP1 536-2AA00 User manual
Siemens
Siemens MICROMASTER 430 FX Operating and maintenance instructions
Siemens
Siemens Cerberus MN7002 Manual
