Siemens CP 343-1 Lean User manual

CP 343- 
1 Lean
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SIMATIC NET
S7-300 - Industrial Ethernet /
PROFINET
CP 343-1 Lean
Manual
Manual Part B
10/2012
C79000−G8976−C198−07
Preface
Properties / services
1
Performance data
2
Requirements for use
3
LEDs
4
Installation, connecting up
and commissioning
5
Notes on configuration and
operation
6
Service and maintenance
7
Technical specifications
8
Approvals
A
References
B

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: C79000−G8976−C198
Ⓟ 10/2012 Technical data subject to change
Copyright © Siemens AG 2009 - 2012.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 3
Preface






Legend:
① LEDs
② Under the front panel:
PROFINET interface, 2 x 8-pin RJ-45 jack
③ Under the front cover:
- Socket for 24 VDC power supply
- Slider for setting the ground connector
④ Order number
⑤ Under the front panel:
printed text with MAC addresses and firmware version
⑥ X = placeholder for hardware product version
Figure 1 CP 343-1 Lean
Validity and product names
This description contains information on the following product:
CP 343−1 Lean
Order number 6GK7 343−1CX10−0XE0
Hardware product version 7
Firmware version V3.0
Communications processor for SIMATIC S7−300 / C7−300

Preface
CP 343-1 Lean
4 Manual, 10/2012, C79000−G8976−C198−07
Note
Names
In this document, the term "CP" is used instead of the full product name.
The name STEP 7 is used for the configuration tool instead of the names STEP 7 V5.5
and STEP 7 Professional.
Innovations and compatibility with the predecessor product
Note
You will find the new functions of the module in the section Enhanced functions (Page 9).
Make sure that you read the information relating to enhanced functions and restrictions that
may apply in the section module replacement / upgrading (Page 50).
Address label: Unique MAC address for the CP
The CP is supplied with total of 3 default MAC addresses with the following assignment:
● PROFINET interface
● One MAC address for each of the 2 Ethernet ports of the PROFINET interface
The MAC addresses of the Ethernet ports are required only for detection and evaluation
of neighborhood and topology relations.
The MAC address of the PROFINET interface is printed on the housing.
Structure of the documentation
The documentation for this device consists of the following parts:
● Manual Part A: Configuration manual "Configuring and Commissioning S7CPs for
Industrial Ethernet", see references /1/ (Page 60).
● Manual Part B: Manual "CP 343-1 Lean" (this manual)
● Program blocks for SIMATIC NET S7 CPs - programming manual, see references /10/
(Page 62)
Contains the detailed description of the program blocks for the following services:
– Open communications services
– Access coordination with FETCH/WRITE
– Connection and system diagnostics
– Programmed connections and IP configuration
– PROFINET IO

Preface
CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 5
Current manual release on the Internet
You will also find the current version of this manual on the Internet pages of Siemens
Automation Customer Support under the following entry ID:
23643456 (http://support.automation.siemens.com/WW/view/en/23643456)
CP documentation in the Manual Collection (order no. A5E00069051)
The "SIMATIC NET Manual Collection" DVD contains the device manuals and descriptions
of all SIMATIC NET products current at the time it was created. It is updated at regular
intervals.
Version History / Current Downloads for the SIMATIC NET S7 CPs
The "Version History/Current Downloads for SIMATIC NET S7 CPs" provides information on
all CPs available up to now for SIMATIC S7 (Industrial Ethernet, PROFIBUS and IE/PB
Link).
An up-to-date version of this document can be found at on the Internet under the entry ID:
9836605 (http://support.automation.siemens.com/WW/view/en/9836605)
SIMATIC NET glossary
Explanations of the specialist terms used in this documentation can be found in the SIMATIC
NET glossary.
You will find the SIMATIC NET glossary here:
● SIMATIC NET Manual Collection
The DVD ships with certain SIMATIC NET products.
● On the Internet under the following entry ID:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
FAQs on the Internet
You will find detailed information (FAQs) on using the CP described here on the Internet at
the following address (entry type "FAQ"):
Link: (http://support.automation.siemens.com/WW/view/en/10806067)

Preface
CP 343-1 Lean
6 Manual, 10/2012, C79000−G8976−C198−07
Security messages
Note
For its automation and drives product portfolio, Siemens provides IT security mechanisms to
support secure operation of the plant/machine. Our products are continuously being further
developed also taking into account the aspect of IT security. We therefore recommend that
you regularly check for updates of our products and that you only use the latest versions.
You will find information in:
(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=
en)
Here, you can register for a product-specific newsletter.
For the secure operation of a plant/machine, it is also necessary to integrate the automation
components in a full IT security concept for the entire plant/machine that represents the state
of the art in IT technology. You will find information on this in:
(http://www.siemens.com/industrialsecurity)
Products from other manufacturers that are being used must also be taken into account.

CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 7
Table of contents
Preface ...................................................................................................................................................... 3
1 Properties / services .................................................................................................................................. 9
1.1 Application......................................................................................................................................9
1.2 Enhanced functions .......................................................................................................................9
1.3 Communication services..............................................................................................................10
1.4 Other services..............................................................................................................................11
1.5 The CP as Web server.................................................................................................................13
2 Performance data .................................................................................................................................... 15
2.1 Transmission and reaction times .................................................................................................15
2.2 Number of possible Ethernet/PROFINET connections................................................................15
2.3 Characteristics of S7 communication ..........................................................................................16
2.4 Characteristic data of the SEND/RECEIVE Interface..................................................................16
2.5 PROFINET IO characteristic data................................................................................................18
2.6 Characteristic data of the integrated switch.................................................................................19
3 Requirements for use .............................................................................................................................. 21
3.1 Operation in control device families.............................................................................................21
3.2 Project engineering ......................................................................................................................23
3.3 Programming................................................................................................................................24
4 LEDs........................................................................................................................................................ 25
5 Installation, connecting up and commissioning........................................................................................ 29
5.1 Important notes on using the device............................................................................................29
5.2 Installing the CP, connecting power and ground .........................................................................31
5.3 Connecting the CP to Ethernet ....................................................................................................34
6 Notes on configuration and operation ...................................................................................................... 37
6.1 Project engineering ......................................................................................................................37
6.2 Controlling the mode....................................................................................................................37
6.3 Network settings ..........................................................................................................................38
6.4 Influence of MPI on connections via Industrial Ethernet..............................................................40
6.5 PROFINET IO when operating other services at the same time.................................................40
6.6 Effects of multicast communication on RT communication .........................................................41
6.7 IP configuration ............................................................................................................................41

Table of contents
CP 343-1 Lean
8 Manual, 10/2012, C79000−G8976−C198−07
6.7.1 Detection of double IP addressing in the network ...................................................................... 41
6.7.2 Obtain IP address vie DHCP: CP STOP on expiry of the lease ................................................. 42
6.8 Media redundancy....................................................................................................................... 42
6.9 Timeofday synchronization ......................................................................................................... 42
6.10 SNMP agent................................................................................................................................ 42
6.11 Possible security gaps on standard IT interfaces: preventing unauthorized access .................. 45
6.12 Programmed communication connections.................................................................................. 45
6.12.1 Programmed communication connections with FB55 IP_CONFIG ............................................ 45
6.12.2 Programmed communications connections - assigning parameters to the ports....................... 46
6.13 Permitted length of ICMP packets .............................................................................................. 46
7 Service and maintenance ........................................................................................................................ 47
7.1 Memory reset / reset to factory defaults...................................................................................... 47
7.2 Loading new firmware................................................................................................................. 48
7.3 Replacing a module .................................................................................................................... 49
7.3.1 Replacing older modules............................................................................................................. 49
7.3.2 module replacement / upgrading ................................................................................................ 50
7.3.3 Replacing a module without a programming device ................................................................... 51
8 Technical specifications........................................................................................................................... 53
A Approvals................................................................................................................................................. 55
B References .............................................................................................................................................. 59
Index........................................................................................................................................................ 67

CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 9
Properties / services 1
1.1 Application
The CP 343- Lean communications processor is intended for operation in a SIMATIC S7-300
or SIMATIC C7 automation system. It allows the connection of the S7-300 to Industrial
Ethernet and supports PROFINET IO.
To integrate the CP in a linear bus or a ring, to connect a further Ethernet device or to use
PROFINET media redundancy, a 2-port ERTEC real-time switch with autocrossing,
autonegotiation and autosensing was integrated.
1.2 Enhanced functions
Abbreviations used with the CP 343-1 Lean module
The module abbreviations used below for the CP 343-1 Lean (for example CX10)
correspond to the last four characters of the mid section of the order number.
Requirement for configuring new functions of firmware version V3.0
To use the features listed below, the following STEP 7 version is necessary:
● STEP 7 V5.5 + Service Pack 2 + Hotfix 1 + HSP 1056
With STEP 7 Professional V11.0 SP2, only the functions of firmware version V2.2 of the CP
can be configured.
Functional enhancements of the CX10 from firmware version V2.6 to V3.0 - can be used with STEP 7
V5.5
The following new functions can be used with the module with firmware version 3.0:
● "Shared device" function with PROFINET IO
● Use of PROFIenergy functionality
This requires the following PROFIenergy program blocks for the CP 343-1 in the
"SIMATIC_NET_CP" library with the STEP 7 version listed above:
– PE_Start_CP, PE_CMD_CP, PE_I_DEV_CP and the program block DS3_WRITE_CP
for the use of power modules of the ET 200S for PROFIenergy.
– The supplementary program blocks FC0 to FC8 for the PROFIenergy response data
can be found in the Standard Library.
You will find the documentation of the program blocks in the online help and in the
manual for the program blocks, see References, /10/ (Page 62).

Properties / services
1.3 Communication services
CP 343-1 Lean
10 Manual, 10/2012, C79000−G8976−C198−07
● New program block FB10 AG_CNTEX for connection diagnostics
● Configuration of the IO devices in the STEP 7 "I-device" dialog box (and as previously
using a GSDML file)
Functional enhancements of the CX10 with firmware version V3.0 - regardless of the configuration
tool used
● Advanced Web diagnostics (HTTP access) with the following additional options:
– Diagnostics of S7 connections
– Module identification
– Expansion of Web diagnostics for The "Shared device" function
● Update center of Web diagnostics with the following functions:
– Downloading firmware via the Web (HTTP access)
– Downloading of language files for diagnostics buffer texts in STEP 7 format for new
modules in the rack and for changing the language
● SNMP: Support of the MRP Monitoring MIB
Enhanced functions of earlier firmware versions and predecessor modules
You will find an overview of the earlier firmware versions and predecessor modules in the
version history of the Industrial Ethernet CPs on the Internet pages of Siemens Automation
Customer Support under the following entry ID:
56699406 (http://support.automation.siemens.com/WW/view/en/56699406)
You will find information about the characteristics of the individual firmware versions on the
Internet pages of Siemens Automation Customer Support under the following entry ID:
43409748 (http://support.automation.siemens.com/WW/view/en/43409748)
> Entry list > Entry type "Updates"
1.3 Communication services
The CP supports the following communication services:
● PROFINET IO
PROFINET IO allows direct access to IO devices over Industrial Ethernet.
– PROFINET IO device
Integration of the SIMATIC S7-300 automation system via the CP as an intelligent
PROFINET IO device (I-device).
– Shared device
Individual submodules of the CP (IO device) can be assigned up to two PROFINET IO
controllers in STEP 7 V5.5.
Note the information on configuring PROFINET IO systems with shared IO devices in
the "PROFINET System Description", see references, /13/ (Page 63).

Properties / services
1.4 Other services
CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 11
● S7 communication and PG/OP communication with the following functions:
– PG functions (including routing)
– Operator control and monitoring functions (HMI)
– Server for data exchange on S7 connections configured at one end only without
communication blocks on the S7300 / C7300 station
● Open communication services with the following functions:
– SEND/RECEIVE interface ISOonTCP, TCP and UDP connections
UDP frame buffering on the CP can be disabled during configuration. When
necessary, this allows you to achieve a shorter reaction time between the arrival of a
UDP frame and its evaluation on the CPU.
– Multicast over UDP connection
The multicast mode is made possible by selecting a suitable IP address when
configuring connections.
– FETCH/WRITE services (server; corresponding to S5 protocol) via ISO-on-TCP
connections and TCP connections
The addressing mode can be configured for FETCH/WRITE access as S7 or S5
addressing mode.
– LOCK/UNLOCK with FETCH/WRITE services
– Connection diagnostics from the user program
1.4 Other services
The CP also provides the following additional services:
● Media redundancy (MRP)
Within an Ethernet network with a ring topology, the CP supports the media redundancy
protocol MRP. You can assign the role of MRP client to the CP.
● Time-of-day synchronization over Industrial Ethernet
Time-of-day synchronization can be configured in the following modes:
– SIMATIC mode
The CP receives MMS time messages and synchronizes its local time and the time of
the CPU.
Accuracy approx. +/- 1 second
You can choose whether or not the time of day is forwarded. The forwarding direction
can also be selected (station > LAN or LAN > station).

Properties / services
1.4 Other services
CP 343-1 Lean
12 Manual, 10/2012, C79000−G8976−C198−07
or
– NTP mode (NTP: Network Time Protocol)
The CP sends timeofday queries at regular intervals to an NTP server and
synchronizes its local time of day. The forwarding of the time-of-day to the CPU is
optional.
Accuracy approx. +/- 1 second
● Addressing using a factoryset MAC address
The CP can be reached via the default MAC address to allow an IP address to be
assigned.
● SNMP agent
The CP supports data queries over SNMP in version V1 (Simple Network Management
Protocol). It delivers the content of certain MIB objects according to the MIB II standard,
LLDP MIB, Automation System MIB and MRP Monitoring MIB.
● Module access protection
To protect the module from accidental or unauthorized access, protection can be
configured at various levels.
● IP configuration
For the PROFINET interface, you can configure how and with which method the CP is
assigned the IP address, the subnet mask and the address of a gateway.
As an alternative to STEP 7, you have the option of assigning the connection
configuration via a block interface in the user program (FB55: IP_CONFIG).
● Web diagnostics
With the aid of Web diagnostics, you can read out the diagnostics data from a station
connected via the CP to a PG/PC with a Web browser.
This makes it possible to read the diagnostics buffers of the intelligent modules in the
rack.
Using the integrated update center of the diagnostics pages, you can download new
firmware versions and diagnostics buffer message texts.
If you do not require the functions, you can disable it in the STEP 7 configuration and
disable port 80.
● Connection diagnostics with the AG_CNTEX program block
With the AG_CNTEX program block, you can diagnose connections.
– When necessary, you can activate or deactivate connections or initiate
reestablishment of a connection.
– You can check the reachability of the connection partners using the ping function.
– You can find out which connection types are set up for the SEND / RECEIVE
interface.

Properties / services
1.5 The CP as Web server
CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 13
1.5 The CP as Web server
Enabling the Web server function
To use the Web server functionality of the CP, enable the relevant option in STEP 7 in the
module properties, "Web" parameter group. This enables port 80 of the CP.
If you no longer require the functions, deactivate the function. The Web server function is
enabled as default.
Web diagnostics
The CP provides you with the functionality of a web server for access by means of a web
browser. The CP provides HTML pages for Web diagnostics. With the aid of Web
diagnostics, you can read out the diagnostics data from a station connected via the CP to a
PG/PC with an Internet browser.
With the following address, you have access to Web diagnostics:
http:\\<IP address of the CP>
Using the integrated update center of the diagnostics pages, you can download new
firmware versions and language files for the diagnostics buffer message texts.
For detailed information on Web diagnostics, refer to the general Part A of this manual, /1/
(Page 60).
Diagnostics buffer entries
When supplied, diagnostics buffer entries shown on diagnostics pages are always in English.
This is the case whichever language you have selected to display the Web pages.
How to download other language files to the CP and further information about Web
diagnostics can be found in the general Part A of this manual.
Web browser
To access the HTML pages on the CP, you require a Web browser. The following Web
browsers are suitable for communication with the CP (other browsers also possible):
● Internet Explorer (recommended version: as of 7.0)
● Chrome (recommended version: as of 12.0)
● Opera (recommended version: as of 9.2)
● Firefox (recommended version: as of 4.0)
You will find these Web browsers, information and any necessary addons on the Internet.

Properties / services
1.5 The CP as Web server
CP 343-1 Lean
14 Manual, 10/2012, C79000−G8976−C198−07

CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 15
Performance data 2
2.1 Transmission and reaction times
Measured values on the Internet
Note
Measured values of transmission and reaction times over Ethernet, PROFIBUS and
PROFINET networks for a series of configurations can be found on the Internet at the
following address:
http://www.siemens.com/automation/pd (http://www.siemens.com/automation/pd)
2.2 Number of possible Ethernet/PROFINET connections
Maximum number of parallel connections
Table 2- 1 Maximum number of parallel connections
Characteristic Explanation / values
Permitted number of simultaneous connections in
total over Industrial Ethernet
12 maximum
Example of maximum load
You can, for example, operate:
● 4 S7 connections
● 4 ISO-on-TCP connections
● 2 TCP connections
● 2 UDP connections
Also:

Performance data
2.3 Characteristics of S7 communication
CP 343-1 Lean
16 Manual, 10/2012, C79000−G8976−C198−07
● Further TCP connections for Web diagnostics
● PROFINET IO
– As PROFINET IO device:
1 PROFINET connection to a PROFINET IO controller
or
– As shared device:
2 PROFINET connections to 2 PROFINET IO controllers
2.3 Characteristics of S7 communication
Number of connections
Table 2- 2 Number of connections for S7 communication
Characteristic Explanation / values
Number of connections for S7 communication via
Industrial Ethernet for:
Operator control and monitoring functions
(HMI)
S7 connections configured at one end
Maximum 4 (one-ended connections)
The number depends on the CPU type being used; the valid values
can be found in /1/ (Page 60).
LAN Interface - data record length per protocol unit
sending
receiving
240 bytes / PDU
240 bytes / PDU
2.4 Characteristic data of the SEND/RECEIVE Interface
The SEND/RECEIVE interface provides access to communication over TCP, ISOonTCP and
UDP connections.
The following characteristics are important:

Performance data
2.4 Characteristic data of the SEND/RECEIVE Interface
CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 17
Table 2- 3 Characteristic data of the SEND/RECEIVE Interface
Characteristic Explanation / values
Number of ISO-on-TCP connections + TCP
connections + UDP connections in total
8 maximum
Notes:
All UDP connections are also possible in
multicast mode.
Free UDP connections are supported by the
CP.
Maximum data length for the blocks AG_SEND
(as of V4.0) and AG_RECV (as of V4.0)
AG_SEND and AG_RECV allow the transfer of
blocks of data with the following length:
1 to 8192 bytes for ISO-on-TCP, TCP;
1 to 2048 bytes for UDP.
Restrictions for UDP
Transfer is not confirmed The transmission of UDP frames is unconfirmed,
in other words the loss of messages is not
detected or displayed by the send block
(AG_SEND).
No receipt of UDP broadcast To avoid communications overload of the CP due
to high broadcast load, the CP does not allow
receipt of UDP broadcasts.
UDP frame buffering Size of the frame buffer with buffering enabled: 2
Kbytes
Note:
Following a buffer overflow, newly arriving frames
are discarded.
Execution times of the FCs AG_SEND / AG_RECV
The execution time required to process the FC blocks (AG_SEND, AG_RECV) required on
the S7-300 / C7-300 CPU is decisive for the calculation of the CPU cycle times (OB1) for
SEND/RECEIVE connections.
Note
Measurements of transmission and reaction times in Ethernet, PROFIBUS and PROFINET
networks for a series of configurations can be found on the Internet at the following address:
25209605 (http://support.automation.siemens.com/WW/view/en/25209605)

Performance data
2.5 PROFINET IO characteristic data
CP 343-1 Lean
18 Manual, 10/2012, C79000−G8976−C198−07
2.5 PROFINET IO characteristic data
Configuration limits of the CP as an IO device and I-device
The CP supports the following maximum configuration if it is configured as a PROFINET IO
device and as an I-device:
Table 2- 4 Configuration limits of the CP as a PROFINET IO device
Characteristic Value
Maximum number of PROFINET IO connections As PROFINET IO device:
1 PROFINET connection to a PROFINET IO
controller
or
As shared device:
2 PROFINET connections to 2 PROFINET IO
controllers
Size of the input area of the PROFINET IO device 512 bytes max. *
Size of the output area of the PROFINET IO
device
512 bytes max. *
Size of the IO data area per sub module on the
PROFINET IO device Inputs: 240 bytes
Outputs: 240 bytes
Size of the consistency area for a submodule 240 bytes
Maximum number of submodules 32
Size of the transfer area 240 bytes
Number of transfer areas 32
* For the size of the user data, refer to the following section.
Size of the user data
The size of the user data is calculated from the maximum frame size (gross 548 bytes)
minus the following values: 1 for the CP itself, 1 per Interface, 1 per port, 1 for each plugged-
in module in HW Config or per slot used.
Table 2- 5 Example of calculating the user data of the CP 343-1 as an IO device
Bytes Explanation
548 Gross size of the frame
-1 for the CP itself
-1 for the Interface
-2 for 2 ports
-32 for the maximum number of pluggable modules
= 512 Net size of the user data *
* By using fewer but larger modules, the amount of user data can be increased.

Performance data
2.6 Characteristic data of the integrated switch
CP 343-1 Lean
Manual, 10/2012, C79000−G8976−C198−07 19
Execution times of the FC blocks PNIO_SEND / PNIO_RECV
The execution time required to process the function blocks (PNIO_SEND, PNIO_RECV)
required on the S7-300 CPU is decisive for the calculation of the reaction times in
PROFINET IO.
Note
Measurements of transmission and reaction times in Ethernet, PROFIBUS and PROFINET
networks for a series of configurations can be found on the Internet at the following address:
25209605 (http://support.automation.siemens.com/WW/view/en/25209605)
2.6 Characteristic data of the integrated switch
Learning addresses / deleting addresses (aging time)
The switch integrated in the CP (PROFINET interface) reads the source addresses included
in the data packets. The switch therefore learns the addresses of the end devices connected
via a port.
If the switch receives a data packet, it directs this packet only to the port via which the
appropriate end node can be reached.
The switch monitors the age of the learned addresses. Addresses that exceed the "aging
time" are deleted. The aging time is 5 minutes.
Ports can be deactivated individually
The ports of the switch integrated in the CP can be deactivated individually in STEP 7 /
HW Config. This can, for example, be used for service purposes.
To do this, open the properties dialog of the relevant port and select the "disabled" setting
under "Options > Transfer medium / duplex".
The port is turned off completely when it is disabled. The corresponding LED on the device
(for example X1P1) is then turned off.

Performance data
2.6 Characteristic data of the integrated switch
CP 343-1 Lean
20 Manual, 10/2012, C79000−G8976−C198−07