Siemens RUGGEDCOM M2200 User manual

RUGGEDCOM M2200
Installation Guide
6/2014
Preface
Introduction 1
Installing Device 2
Communication Ports 3
Technical Specifications 4
Dimension Drawings 5
Certification 6
RC1044-EN-04

RUGGEDCOM M2200
Installation Guide
ii
Copyright © 2014 Siemens Canada Ltd.
All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized
except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or
trademark registration.
This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the prior written consent of Siemens Canada Ltd..
Disclaimer Of Liability
Siemens has verified the contents of this manual against the hardware and/or software described. However, deviations between the product
and the documentation may exist.
Siemens shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing,
performance, or use of this material.
The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We
appreciate any suggested improvements. We reserve the right to make technical improvements without notice.
Registered Trademarks
ROX™, Rugged Operating System On Linux™, CrossBow™ and eLAN™ are trademarks of Siemens Canada Ltd.. ROS® is a registered
trademark of Siemens Canada Ltd..
Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the
owner.
Third Party Copyrights
Siemens recognizes the following third party copyrights:
• Copyright © 2004 GoAhead Software, Inc. All Rights Reserved.
Security Information
Siemens provides products and solutions with industrial security functions that support the secure operation of plants, machines, equipment
and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens’ products and solutions
undergo continuous development. Siemens recommends strongly that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept)
and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also
be considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit http://
support.automation.siemens.com.
Warranty
Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance
during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all
warranties null and void. The warranties set forth in this article are exclusive and are in lieu of all other warranties, performance guarantees
and conditions whether written or oral, statutory, express or implied (including all warranties and conditions of merchantability and fitness for
a particular purpose, and all warranties and conditions arising from course of dealing or usage or trade). Correction of nonconformities in the
manner and for the period of time provided above shall constitute the Seller’s sole liability and the Customer’s exclusive remedy for defective
or nonconforming goods or services whether claims of the Customer are based in contract (including fundamental breach), in tort (including
negligence and strict liability) or otherwise.
For warranty details, visit www.siemens.com/ruggedcom or contact a Siemens customer service representative.
Contacting Siemens
Address
Siemens Canada Ltd.
Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7
Telephone
Toll-free: 1 888 264 0006
Tel: [phone]
Fax: [phone]
E-mail
[email protected]
Web
www.siemens.com/ruggedcom

RUGGEDCOM M2200
Installation Guide Table of Contents
iii
Table of Contents
Preface ................................................................................................................ v
Alerts .................................................................................................................................................. v
Related Documents ............................................................................................................................. v
Accessing Documentation .................................................................................................................... v
Training .............................................................................................................................................. vi
Customer Support .............................................................................................................................. vi
Chapter 1
Introduction .......................................................................................................... 1
1.1 Feature Highlights ........................................................................................................................ 1
1.2 Ports, Controls and Indicator LEDs ............................................................................................... 2
Chapter 2
Installing Device .................................................................................................. 5
2.1 Mounting the Device to a Panel .................................................................................................... 5
2.2 Connecting Power ........................................................................................................................ 6
2.2.1 Connecting AC Power ....................................................................................................... 7
2.2.2 Connecting DC Power ....................................................................................................... 8
2.2.3 Wiring Examples ............................................................................................................. 10
2.3 Connecting the Failsafe Alarm Relay ........................................................................................... 12
2.4 Grounding the Device ................................................................................................................. 13
2.5 Connecting to the Device ........................................................................................................... 13
2.6 Cabling Recommendations ......................................................................................................... 14
2.6.1 Protection On Twisted-Pair Data Ports .............................................................................. 15
2.6.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations ................................................. 15
Chapter 3
Communication Ports ......................................................................................... 17
3.1 Copper Ethernet Ports ................................................................................................................ 18
3.2 Fiber Optic Ethernet Ports .......................................................................................................... 19
3.3 SFP Optic Ethernet Ports ........................................................................................................... 20
3.3.1 Installing an SFP Optical Port .......................................................................................... 20
3.3.2 Removing an SFP Optical Port ......................................................................................... 21

Table of Contents
RUGGEDCOM M2200
Installation Guide
iv
Chapter 4
Technical Specifications ..................................................................................... 23
4.1 Power Supply Specifications ....................................................................................................... 23
4.2 Failsafe Relay Specifications ...................................................................................................... 23
4.3 Supported Networking Standards ................................................................................................ 24
4.4 Copper Ethernet Port Specifications ............................................................................................ 24
4.5 Fiber Optic Ethernet Port Specifications ....................................................................................... 25
4.5.1 10FL Ethernet Optical Specifications ................................................................................ 25
4.5.2 Gigabit Ethernet (1 Gbps) Optical Specifications ................................................................ 25
4.6 Operating Environment ............................................................................................................... 26
4.7 Mechanical Specifications ........................................................................................................... 26
Chapter 5
Dimension Drawings .......................................................................................... 27
Chapter 6
Certification ........................................................................................................ 29
6.1 Agency Approvals ...................................................................................................................... 29
6.2 FCC Compliance ........................................................................................................................ 29
6.3 Industry Canada Compliance ...................................................................................................... 29
6.4 EMI and Environmental Type Tests ............................................................................................. 30

RUGGEDCOM M2200
Installation Guide Preface
Alerts v
Preface
This guide describes the RUGGEDCOM M2200. It describes the major features of the device, installation,
commissioning and important technical specifications.
It is intended for use by network technical support personnel who are responsible for the installation,
commissioning and maintenance of the device. It is also recommended for use by network and system planners,
system programmers, and line technicians.
Alerts
The following types of alerts are used when necessary to highlight important information.
DANGER!
DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or
serious injury.
WARNING!
WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or
equipment damage.
CAUTION!
CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.
IMPORTANT!
IMPORTANT alerts provide important information that should be known before performing a procedure
or step, or using a feature.
NOTE
NOTE alerts provide additional information, such as facts, tips and details.
Related Documents
Other documents that may be of interest include:
• ROS User Guide for the M2200
Accessing Documentation
The latest Hardware Installation Guides and Software User Guides for most RUGGEDCOM products are
available online at www.siemens.com/ruggedcom.

Preface
RUGGEDCOM M2200
Installation Guide
vi Training
For any questions about the documentation or for assistance finding a specific document, contact a Siemens
sales representative.
Training
Siemens offers a wide range of educational services ranging from in-house training of standard courses on
networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs,
experience and application.
Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make
sure users have the right knowledge and expertise to understand the various technologies associated with critical
communications network infrastructure technologies.
Siemens' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility,
transportation and industrial markets, allows Siemens to provide training specific to the customer's application.
For more information about training services and course availability, visit www.siemens.com/ruggedcom or
contact a Siemens sales representative.
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or
general information, please contact Siemens Customer Support through any of the following methods:
•Online
Visit http://www.siemens.com/automation/support-request to submit a Support Request (SR) or check on the
status of an existing SR.
•Telephone
Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit http://
www.automation.siemens.com/mcms/aspa-db/en/automation-technology/Pages/default.aspx.
•Mobile App
Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device
and be able to:
▪ Access Siemens's extensive library of support documentation, including FAQs, manuals, and much more
▪ Submit SRs or check on the status of an existing SR
▪ Find and contact a local contact person
▪ Ask questions or share knowledge with fellow Siemens customers and the support community via the forum
▪ And much more...

RUGGEDCOM M2200
Installation Guide
Chapter 1
Introduction
Feature Highlights 1
Introduction
The RUGGEDCOM M2200 is a rugged, fully managed, modular Ethernet switch specifically designed to operate
reliably in electrically harsh and climatically demanding utility substation, railway and industrial environments.
The M2200’s superior rugged hardware design coupled with the embedded Rugged Operating System (ROS)
provides improved system reliability and advanced cyber security and networking features, making it ideally
suited for creating Ethernet networks for mission-critical, real-time, control applications.
The following sections provide more information about the M2200:
•Section 1.1, “Feature Highlights”
•Section 1.2, “Ports, Controls and Indicator LEDs”
Section 1.1
Feature Highlights
Ethernet Ports
• Up to 9-Gigabit Ethernet ports supporting copper and fiber media
• Up to 9 100FX Fiber Fast Ethernet ports
• 2 port modules for tremendous flexibility
• Fiber types supported include multimode, singlemode, and bidirectional single strand
• Full compliance with IEEE: 802.3, 802.3u & 802.3z
• Non-blocking, store and forward switching
• Full duplex operation and flow control (IEEE 802.3x)
• Industry standard fiber optic connectors: LC, SC, SFP, GBIC
• Long haul optics allow Gigabit distances up to 70 km
Cyber Security Features
• Multi-level user passwords
• SSH/SSL encryption
• MAC-based port security
• Selective port enable/disable
• Port-based network access control using IEEE 802.1x
• VLAN support (IEEE 802.1Q) to segregate and secure network traffic
• RADIUS centralized access management
• SNMPv3 featuring encrypted authentication and session
Rated for Reliability in Harsh Environments
• Immunity to EMI and heavy electrical transients:
▪ Meets IEEE 1613 (electric utility substations)

Chapter 1
Introduction
RUGGEDCOM M2200
Installation Guide
2 Ports, Controls and Indicator LEDs
▪ Exceeds IEC 61850-3 (electric utility substations)
▪ Exceeds IEC 61800-3 (variable speed drive systems)
▪ Exceeds NEMA TS-2 (traffic control equipment)
▪ Exceeds IEC 61000-6-2 (generic industrial environment)
• -40 to 85 °C (-40 to 185 °F) operating temperature (no fans)
• Conformal coated printed circuit boards (optional)
• 18 AWG galvanized steel enclosure
Universal Power Supply Options
• Fully integrated, dual-redundant (optional) power supplies
• Universal high-voltage range: 88-300 VDC or 85-264 VAC
• Popular low voltage ranges: 24 VDC (10-36 VDC), 48 VDC (36-72 VDC)
• Screw or pluggable terminal blocks for reliable, maintenance-free connections
• CSA/UL 60950-1 safety approved to 85 °C (185 °F)
Section 1.2
Ports, Controls and Indicator LEDs
The M2200 features various ports, controls and indicator LEDs on the front panel for configuring and
troubleshooting the device.
5
1
3 6
4
2
Figure 1: Front Panel
1. Port Status Indicator LEDs 2. Display Mode Indicator LEDs 3. Mode Button 4. Alarm Indicator LED 5. Power Module Indicator
LEDs 6. RS232 Serial Console Port (RJ45)
Port Status Indicator LEDs These LEDs indicate the state of each port.
When Status mode is selected, these LEDs indicate when ports are active.
• Green (Solid) = Link detected
• Green (Blinking) = Link activity
• Off = No link detected
When Duplex mode is selected, these LEDs indicate when ports are operating in full or half
duplex mode.
• Green (Solid) = Full duplex mode

RUGGEDCOM M2200
Installation Guide
Chapter 1
Introduction
Ports, Controls and Indicator LEDs 3
• Orange (Solid) = Half duplex mode
• Off = No link detected
When Speed mode is selected, these LEDs indicate the port speed.
• Green (Solid) = 1000 Mb/s
• Green (Blinking) = 100 Mb/s
• Orange (Solid) = 10 Mb/s
• Off = No link detected
Display Mode Indicator LEDs These LEDs indicate the current display mode for the port status indicator LEDs (i.e. Status,
Duplex or Speed).
Mode button The Mode button sets the display mode for the port status indicator LEDs (i.e. Status,
Duplex or Speed). It can also be used to reset the device if held for 5 seconds.
Alarm Indicator LED The alarm indicator LED illuminates when an alarm condition exists.
Power Module Indicator LEDs These LEDs indicate the status of the power modules.
• Green = The power supply is supplying power
• Red = Power supply failure
• Off = No power supply is installed
RS232 Serial Console Port This port is for interfacing directly with the device and accessing initial management
functions.

RUGGEDCOM M2200
Installation Guide
Chapter 1
Introduction
Ports, Controls and Indicator LEDs 4

RUGGEDCOM M2200
Installation Guide
Chapter 2
Installing Device
Mounting the Device to a Panel 5
Installing Device
The following sections describe how to install the device, including mounting the device, installing/removing
modules, connecting power, and connecting the device to the network.
DANGER!
Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing
any maintenance tasks, make sure all power to the device has been disconnected and wait
approximately two minutes for any remaining energy to dissipate.
WARNING!
Radiation hazard – risk of serious personal injury. This product contains a laser system and is
classified as a CLASS 1 LASER PRODUCT. Use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous radiation exposure.
IMPORTANT!
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall
render all warranties null and void.
Changes or modifications not expressly approved by Siemens Canada Ltd. could invalidate
specifications, test results, and agency approvals, and void the user's authority to operate the
equipment.
IMPORTANT!
This product should be installed in a restricted access location where access can only be gained by
authorized personnel who have been informed of the restrictions and any precautions that must be
taken. Access must only be possible through the use of a tool, lock and key, or other means of security,
and controlled by the authority responsible for the location.
•Section 2.1, “Mounting the Device to a Panel”
•Section 2.2, “Connecting Power”
•Section 2.3, “Connecting the Failsafe Alarm Relay”
•Section 2.4, “Grounding the Device”
•Section 2.5, “Connecting to the Device”
•Section 2.6, “Cabling Recommendations”
Section 2.1
Mounting the Device to a Panel
For panel installations, the M2200 can be equipped with panel adapters pre-installed on each side of the chassis.
The adapters allow the device to be attached to a panel using screws.
To mount the device to a panel, do the following:
1. Place the device against the panel and align the adapters with the mounting holes.

Chapter 2
Installing Device
RUGGEDCOM M2200
Installation Guide
6 Connecting Power
11
11
2
2
2
Figure 2: Panel Mounting
1. Screw 2. Panel Adaptor
2. Install the supplied screws to secure the adapters to the panel.
Section 2.2
Connecting Power
The M2200 supports single or dual redundant AC and/or DC power supplies. The use of two power modules is
recommended to provide redundancy and load balancing.
The M2200 can be equipped with either a screw-type or pluggable terminal block, which provides power to both
power supplies. The screw-type terminal block is installed using Philips screws and compression plates, allowing
either bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable connections
under severe shock or vibration.
NOTE
• For maximum redundancy in a dual power supply configuration, use two independent power
sources.
• Use only #16 gage copper wiring when connecting terminal blocks.

RUGGEDCOM M2200
Installation Guide
Chapter 2
Installing Device
Connecting AC Power 7
• For 100-240 VAC rated equipment, an appropriately rated AC circuit breaker must be installed.
• For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker must be installed.
• A circuit breaker is not required for 12, 24 or 48 VDC rated power supplies.
• It is recommended to provide a separate circuit breaker for each power supply module.
• Equipment must be installed according to applicable local wiring codes and standards.
The following sections describe how to connect power to the device:
•Section 2.2.1, “Connecting AC Power”
•Section 2.2.2, “Connecting DC Power”
•Section 2.2.3, “Wiring Examples”
Section 2.2.1
Connecting AC Power
To connect a high AC power supply to the device, do the following:
CAUTION!
Electrical hazard – risk of damage to equipment. Do not connect AC power cables to terminals for DC
power. Damage to the power supply may occur.
CAUTION!
Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the
field, remove the metal jumper. This metal jumper connects transient suppression circuitry to chassis
ground and must be removed in order to avoid damage to transient suppression circuitry during testing.
NOTE
The terminal block is divided into separate terminals for each internal power supply. Make sure to
connect the external power supply to the appropriate terminals.
1. Remove the terminal block cover.
2. If a screw-type terminal block is installed, remove the screws from the appropriate terminals. Use these
screws along with #6 ring lugs to secure the wires to the terminal block.
3. Connect the positive wire from the power source to the positive/live (+/L) terminal on the terminal block. For
more information, refer to Section 2.2.3, “Wiring Examples”.

Chapter 2
Installing Device
RUGGEDCOM M2200
Installation Guide
8 Connecting DC Power
4
21
34
6
5
7
4
6
5
3
6
5
7
4
6
5
Figure 3: Terminal Block Wiring
1. Screw-Type Terminal Block 2. Pluggable Terminal Block 3. Jumper 4. Positive/Live (+/L) Terminal 5. Negative/Neutral (-/N)
Terminal (-/N) 6. Surge Ground Terminal 7. Chassis Ground Terminal
4. Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.
For more information, refer to Section 2.2.3, “Wiring Examples”.
5. Install the supplied metal jumper between terminals 2, 4 and 6 to connect the surge ground terminals to the
chassis ground terminal. The surge ground terminals are used as the ground conductor for all surge and
transient suppression circuitry internal to the unit.
6. Connect the ground terminal on the power source to the chassis ground terminal on the device. For more
information, refer to Section 2.4, “Grounding the Device”
DANGER!
Electrocution hazard – risk of death, serious personal injury and/or damage to the device. Make
sure the supplied terminal block cover is always installed before the device is powered.
7. Install the terminal block cover.
Section 2.2.2
Connecting DC Power
To connect a high or low DC power supply to the device, do the following:
CAUTION!
Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the
field, remove the metal jumper. This metal jumper connects transient suppression circuitry to chassis
ground and must be removed in order to avoid damage to transient suppression circuitry during testing.
NOTE
The terminal block is divided into separate terminals for each internal power supply. Make sure to
connect the external power supply to the appropriate terminals.

RUGGEDCOM M2200
Installation Guide
Chapter 2
Installing Device
Connecting DC Power 9
NOTE
The screw-type terminal block is installed using Philips screws and compression plates, allowing either
bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable screws, which
must be removed to make connections.
1. Remove the terminal block cover.
2. If a screw-type terminal block is installed, remove the screws from the appropriate terminals. Use these
screws along with #6 ring lugs to secure the wires to the terminal block.
3. Connect the positive wire from the power source to the positive/live (+/L) terminal on the terminal block. For
more information, refer to Section 2.2.3, “Wiring Examples”.
4
21
34
6
5
7
4
6
5
3
6
5
7
4
6
5
Figure 4: Terminal Block Wiring
1. Screw-Type Terminal Block 2. Pluggable Terminal Block 3. Jumper 4. Positive/Live (+/L) Terminal 5. Negative/Neutral (-/N)
Terminal (-/N) 6. Surge Ground Terminal 7. Chassis Ground Terminal
4. Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.
For more information, refer to Section 2.2.3, “Wiring Examples”.
5. Install the supplied metal jumper between terminals 2, 4 and 6 to connect the surge ground terminals to the
chassis ground terminal. The surge ground terminals are used as the ground conductor for all surge and
transient suppression circuitry internal to the unit.
6. Connect the ground terminal on the power source to the chassis ground terminal on the device. For more
information, refer to Section 2.4, “Grounding the Device”
DANGER!
Electrocution hazard – risk of death, serious personal injury and/or damage to the device. Make
sure the supplied terminal block cover is always installed before the device is powered.
7. Install the terminal block cover.

Chapter 2
Installing Device
RUGGEDCOM M2200
Installation Guide
10 Wiring Examples
Section 2.2.3
Wiring Examples
The following illustrate how to connect power to single and dual power supplies.
Figure 5: Single AC Power Supply
Figure 6: Single DC Power Supply

RUGGEDCOM M2200
Installation Guide
Chapter 2
Installing Device
Wiring Examples 11
Figure 7: Dual AC Power Supply
Figure 8: Dual DC Power Supply

Chapter 2
Installing Device
RUGGEDCOM M2200
Installation Guide
12 Connecting the Failsafe Alarm Relay
Figure 9: Dual AC/DC Power Supply
Section 2.3
Connecting the Failsafe Alarm Relay
The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is
closed when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm
is configured, the relay opens the NO contact and closes the NC (Normally Closed) contact.
NOTE
Control of the failsafe relay output is configurable through ROS. One common application for this relay
is to signal an alarm if a power failure occurs. For more information, refer to the ROS User Guide for
the M2200.
The following shows the proper relay connections.

RUGGEDCOM M2200
Installation Guide
Chapter 2
Installing Device
Grounding the Device 13
13
2
Figure 10: Failsafe Alarm Relay Wiring
1. Normally Open 2. Common 3. Normally Closed
Section 2.4
Grounding the Device
The M2200 chassis ground terminal uses a #6-32 screw. It is recommended to terminate the ground connection
with a #6 ring lug and torque it to 1.7 N·m (15 lbf·in).
2
1
3
Figure 11: Chassis Ground Connection
1. Stainless Steel Stud 2. #6-32 Screw 3. #6 Ring Lug
Section 2.5
Connecting to the Device
The following describes the various methods for accessing the ROS console and Web interfaces on the device.
For more detailed instructions, refer to the ROS User Guide for the M2200.

Chapter 2
Installing Device
RUGGEDCOM M2200
Installation Guide
14 Cabling Recommendations
RS232 Console Port
Connect a PC or terminal directly to the RS232 console port to access the boot-time control and ROS interfaces.
The console port provides access to ROS's console and Web interfaces.
IMPORTANT!
The console port is intended to be used only as a temporary connection during initial configuration or
troubleshooting.
Connection to the console port is made using an RJ45-to-DB9 console cable. The following is the pin-out for the
console port:
18
Figure 12: RJ45 Console Port Pin Configuration
Pin
RJ45
Male
DB9
Female
Name Description Comment
1 6 DSRaData Set Ready
2 1 DCDaCarrier Detect Reserved (Do
Not Connect)
3 4 DTRaData Terminal
Ready
4 5 GND Signal Ground
5 2 RxD Receive Data
(to DTE)
6 3 TxD Transmit Data
(from DTE)
7 8 CTSbClear to Send
8 7 RTSbRead to Send
1 9 RIcRing Indicator
aThe DSR, DCD and DTR pins are connected together internally.
bThe CTS and RTS pins are connected together internally.
cRI is not connected.
Communication Ports
Connect any of the available Ethernet ports on the device to a management switch and access the ROS console
and Web interfaces via the device's IP address. For more information about available ports, refer to Chapter 3,
Communication Ports.
Section 2.6
Cabling Recommendations
Before connecting the device, be aware of the recommendations and considerations outlined in the following
sections:
•Section 2.6.1, “Protection On Twisted-Pair Data Ports”
•Section 2.6.2, “Gigabit Ethernet 1000Base-TX Cabling Recommendations”