Siemens SITRANS LR560 User manual

Radar Transmitters
Operating Instructions 10/2010
SITRANS LR560 (Foundation Fie dbus)
SITRANS
Draft_Rev. 1.0-02
Firmware 1.00.00-32

© Siemens AG 2010
Safety Guidelines: Warning notices must be observed to ensure personal safety as well as that of
others, and to protect the product and the connected equipment. These warning notices are
accompanied by a clarification of the level of caution to be observed.
Qualified Personnel: This device/system may only be set up and operated in conjunction with this
manual. Qualified personnel are only authorized to install and operate this equipment in accordance with
established safety practices and standards.
Unit Repair and Excluded Liability:
•The user is responsible for all changes and repairs made to the device by the user or the user’s
agent.
•All new components are to be provided by Siemens Milltronics Process Instruments.
•Restrict repair to faulty components only.
•Do not reuse faulty components.
Warning: Cardboard shipping package provides limited humidity and moisture protection. This product
can only function properly and safely if it is correctly transported, stored, installed, set up, operated, and
maintained.
This product is intended for use in industrial areas. Operation of this equipment in a residential area
may cause interference to several frequency based communications.
Note: Always use product in accordance with specifications.
Copyright Siemens AG 2010. All Rights
Reserved
Disclaimer of Liability
This document is available in bound version and in
electronic version. We encourage users to purchase
authorized bound manuals, or to view electronic
versions as designed and authored by Siemens
Milltronics Process Instruments. Siemens Milltronics
Process Instruments will not be responsible for the
contents of partial or whole reproductions of either
bound or electronic versions.
While we have verified the contents of this
manual for agreement with the
instrumentation described, variations remain
possible. Thus we cannot guarantee full
agreement. The contents of this manual are
regularly reviewed and corrections are
included in subsequent editions. We welcome
all suggestions for improvement.
Technical data subject to change.
MILLTRONICS®is a registered trademark of Siemens Milltronics Process Instruments.
Contact SMPI Technical Publications European Authorized Representative
at the following address:
Technical Publications Siemens AG
Siemens AG Industry Sector
Siemens Milltronics Process Instruments 76181 Karlsruhe
1954 Technology Drive, P.O. Box 4225 Deutschland
Peterborough, Ontario, Canada, K9J 7B1
Email: [e-mail]
•For a selection of Siemens Milltronics level measurement manuals, go to:
www. siemens.com/processautomation. Under Process Instrumentation, select
Level
Measurement
and then go to the manual archive listed under the product family.
•For a selection of Siemens Milltronics weighing manuals, go to:
www. siemens.com/processautomation. Under Weighing Technology, select
Continuous
Weighing Systems
and then go to the manual archive listed under the product family.

i
mmmmm
Table of Contents
Table of Contents
Safety Notes .............................................................................................................................................1
Safety marking symbols ..............................................................................................................1
FCC Conformity ........................................................................................................................................1
CE Electromagnetic Compatibility (EMC) Conformity ....................................................................2
Industry Canada ......................................................................................................................................2
The Manual ...............................................................................................................................................3
Application Example .....................................................................................................................3
Technical Support ....................................................................................................................................4
Abbreviations and Identifications .............................................................................................4
SITRANS LR560 Overview .................................................................................................6
Programming ............................................................................................................................................6
Local Display Interface (LDI) ......................................................................................................7
Versions .....................................................................................................................................................7
Applications ..............................................................................................................................................7
Approvals and Certificates ...................................................................................................................7
Specifications ......................................................................................................................8
Dimensions ............................................................................................................................................12
Universal Slotted Flange ...........................................................................................................16
Installation ......................................................................................................................... 17
Pressure Equipment Directive, PED, 97/23/EC ...............................................................................17
Mounting location .................................................................................................................................18
Nozzle location .............................................................................................................................18
Aimer Adjustment .......................................................................................................................19
Air Purging System ...............................................................................................................................20
Purge Connection ........................................................................................................................21
Removable Display ...............................................................................................................................22
Wiring ..................................................................................................................................23
Power .......................................................................................................................................................23
Connecting SITRANS LR560 ...............................................................................................................23
Basic Configuration with Foundation Fieldbus (H1) ...........................................................25
Wiring Setups for hazardous area installations ...........................................................................26
Configuration with Foundation Fieldbus for hazardous areas ........................................26
Instructions specific to hazardous area installations ........................................................29
Local Operation .................................................................................................................30
Activating SITRANS LR560 .................................................................................................................30
The LCD Display ...........................................................................................................................31
Handheld Programmer ..............................................................................................................32
Programming SITRANS LR560 .................................................................................................32
To configure a device via the local user interface ........................................................................35
Quick Start Wizard via the LDI push buttons .......................................................................36
Quick Start Wizard via the handheld programmer .............................................................36
Requesting an Echo Profile ................................................................................................................39
Device Address ......................................................................................................................................39

ii
mmmmm
Table of Contents
Level application example ...................................................................................................................40
Operating via AMS Device Manager ............................................................................41
Functions in AMS Device Manager .................................................................................................41
Key Features of AMS Device Manager version 9.0. ...........................................................42
Block location of features .........................................................................................................42
Programming via AMS Device Manager ........................................................................................43
Navigating through the parameters .......................................................................................43
Pull-down menu access ............................................................................................................43
Changing parameter settings ...................................................................................................43
Adding a new device ............................................................................................................................44
Electronic Device Description (EDD) ......................................................................................44
Startup .....................................................................................................................................................44
Configuring a new device ...................................................................................................................46
Quick Start Wizard via AMS Device Manager ....................................................................46
Changing Block Modes ........................................................................................................................49
Configure/Setup Parameters ..............................................................................................................49
Transducer Block Parameters ..................................................................................................49
Level Transducer Block Parameters .......................................................................................51
Configure/Setup (Liquid Crystal Display Block-LCD) ..........................................................59
Configure/Setup (Diagnostic Transducer Block-DIAG) .....................................................61
Configure/Setup (Resource Block - RESOURCE) ................................................................61
Device Diagnostics (Level Transducer Block - LTB) ...........................................................68
Device Diagnostics (Level Control Device Block - LCD) ....................................................70
Device Diagnostics (Diagnostic Transducer Block - DIAG) ..............................................70
Device Diagnostics (Resource Block - RESOURCE) ...........................................................70
Password Protection ............................................................................................................................74
User Manager utility ...................................................................................................................74
AMS Menu Structure ......................................................................................................75
Parameter Reference ......................................................................................................86
Quick Start .................................................................................................................................. 86
Quick Start Wizard.......................................................................................................... 86
AFES (Auto False Echo Suppression) Wizard .......................................................... 87
Copy Parameters to Display......................................................................................... 88
Copy Parameters from Display.................................................................................... 88
Copy Firmware to Display ............................................................................................. 88
Copy Firmware from Display ........................................................................................ 89
Setup ............................................................................................................................................ 89
Identification..................................................................................................................... 89
Device ................................................................................................................................ 90
Sensor................................................................................................................................ 90
Signal Processing............................................................................................................ 94
AIFB 1.............................................................................................................................. 103
AIFB 2.............................................................................................................................. 107
Measured Values......................................................................................................... 107
Filtering ........................................................................................................................... 107
Diagnostics.............................................................................................................................. 108
Echo Profile.................................................................................................................... 108
Fault Reset ..................................................................................................................... 109

iii
mmmmm
Table of Contents
Trend ............................................................................................................................... 109
Electronics Temperature............................................................................................ 109
Peak Values................................................................................................................... 109
Service...................................................................................................................................... 110
Master Reset................................................................................................................. 110
Remaining Device Lifetime ........................................................................................ 111
Remaining Sensor Lifetime........................................................................................ 113
Service Schedule ......................................................................................................... 115
Calibration Schedule ................................................................................................... 117
Powered Hours............................................................................................................. 119
Power-on Resets.......................................................................................................... 119
Menu Timeout............................................................................................................... 119
LCD Backlight................................................................................................................ 119
LCD Contrast.................................................................................................................. 119
Secondary Value .......................................................................................................... 120
Simulate Enable............................................................................................................ 120
Demo Mode................................................................................................................... 120
Communication....................................................................................................................... 120
Tag ................................................................................................................................... 120
Device Address............................................................................................................. 121
Manufacturer ................................................................................................................ 121
Device Type Identification.......................................................................................... 121
Device Revision ............................................................................................................ 121
ITK Version..................................................................................................................... 121
Security..................................................................................................................................... 121
Remote Access............................................................................................................. 121
Local Access ................................................................................................................. 122
Language.................................................................................................................................. 122
Appendix A: Alphabetical Parameter List .................................................................. 123
Appendix B: Troubleshooting ....................................................................................... 128
Communication Troubleshooting ....................................................................................................128
Device Status Icons ............................................................................................................................129
General Fault Codes ...........................................................................................................................130
Operation Troubleshooting ...............................................................................................................134
..................................................................................................................................................................135
Appendix C: Maintenance ............................................................................................ 136
Unit Repair and Excluded Liability ..................................................................................................136
Appendix D: Technical Reference ............................................................................... 137
Principles of Operation ......................................................................................................................137
Process Variables ......................................................................................................................137
Echo Processing ..................................................................................................................................138
Process Intelligence .................................................................................................................138
Echo Selection ...........................................................................................................................138
Measurement Range .........................................................................................................................143
Measurement Response ...................................................................................................................144
Damping .................................................................................................................................................144
Loss of Echo (LOE) ...............................................................................................................................144

iv
mmmmm
Table of Contents
Loss of Echo (LOE) Timer (2.3.4.) ............................................................................................145
Temperature derating curves ...........................................................................................................145
Appendix E: Communications ..................................................................................... 147
Foundation Fieldbus (FF) Protocol .........................................................................................147
Field Communicator 375 (FC375) ............................................................................................147
Appendix F: Firmware Revision History ..................................................................... 148
Glossary ............................................................................................................................ 149
Index .................................................................................................................................. 153
LCD menu structure ....................................................................................................... 155

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 1
mmmmm
SITRANS LR560 (FF)
Safety Notes
Special attention must be paid to warnings and notes highlighted from the rest of the text
by grey boxes.1)
Safety marking symbols
FCC Conformity
US Installations only: Federal Communications Commission (FCC) rules
WARNING symbol relates to a caution symbol on the product, and
means that failure to observe the necessary precautions can result
in death, serious injury, and/or considerable material damage.
WARNING symbol, used when there is no corresponding caution
symbol on the product, means that failure to observe the necessary
precautions can result in death, serious injury, and/or considerable
material damage.
Note: means important information about the product or that part of the operating
manual.
1) This symbol is used when there is no corresponding caution symbol on the product.
In manual On
product Description
Earth (ground) Terminal
Protective Conductor Terminal
(Label on product: yellow background.) WARNING: refer
to accompanying documents (manual) for details.
WARNING: Changes or modifications not expressly approved by
Siemens Milltronics could void the user’s authority to operate the
equipment.
Notes:
• This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
• This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference to radio communications, in which case
the user will be required to correct the interference at his own expense.

Page 2 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
SITRANS LR560 (FF)
CE Electromagnetic Compatibility (EMC) Conformity
This equipment has been tested and found to comply with the following EMC Standards:
Industry Canada
a) Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
b) This device shall be installed and operated in a completely enclosed container to
prevent RF emission which otherwise can interfere with aeronautical navigation.
Installation shall be done by trained installers, in strict compliance with the
manufacturer’s instructions.
c) The use of this device is on a “no-interference, no-protection” basis. That is, the
user shall accept operations of high-powered radar in the same frequency band
which may interfere with or damage this device. On the other hand, level probing
devices found to interfere with primary licensing operations will be required to be
removed at the user’s expense.
EMC Standard Title
CISPR 11:2004/EN
55011:1998+A1:1999&A2:2002, CLASS B
Limits and methods of measurements of radio
disturbance characteristics of industrial, scientific,
and medical (ISM) radio-frequency equipment.
EN 61326:1997+A1:1998+A2:2001+A3:2003
(IEC 61326:2002)
Electrical Equipment for Measurement, Control and
Laboratory Use – Electromagnetic Compatibility.
EN61000-4-2:2001
Electromagnetic Compatibility (EMC) Part 4-2:Testing
and measurement techniques – Electrostatic
discharge immunity test.
EN61000-4-3:2002
Electromagnetic Compatibility (EMC) Part 4-3:
Testing and measurement techniques – Radiated,
radio-frequency, electromagnetic field immunity test.
EN61000-4-4:2004
Electromagnetic Compatibility (EMC) Part 4-4:
Testing and measurement techniques – Electrical
fast transient/burst immunity test.
EN61000-4-5:2001
Electromagnetic Compatibility (EMC) Part 4-5:
Testing and measurement techniques – Surge
immunity test.
EN61000-4-6:2004
Electromagnetic Compatibility (EMC) Part 4-6:
Testing and measurement techniques – Immunity to
conducted disturbances, induced by radio-frequency
fields.
EN61000-4-8:2001
Electromagnetic Compatibility (EMC) Part 4-8:
Testing and measurement techniques – Power
frequency magnetic field immunity test.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 3
mmmmm
SITRANS LR560 (FF)
d) This level probing device is only permitted for installation inside enclosed
containers. The installer/user of this device shall ensure that it is at least 10 km from
the Penticton radio astronomy station (British Columbia latitude: 49° 19' 12" N,
longitude: 119° 37'12" W). For devices not meeting this 10 km separation (e.g. the
Okanagan Valley, British Columbia) the installer/ user must coordinate with and
obtain the written concurrence of the Director of the Penticton radio astronomy
station before the equipment can be installed or operated. The Penticton contact is
Tel: [phone]/ fax: [phone]. (In case of difficulty, the Manager, Radio
Equipment Standards, Industry Canada, may also be contacted.)
The Manual
This manual will help you set up your SITRANS LR560 for optimum performance.
Foundation Fieldbus for Level instruments (7ML19985MP01) manual provides details on
FF communication. 1)
We always welcome suggestions and comments about manual content, design, and
accessibility. Please direct your comments to [email protected].
For other Siemens Milltronics level measurement manuals, go to:
www.siemens.com/level, and look under Level Measurement.
Application Example
The application example used in this manual illustrates a typical installation using
SITRANS LR560. (See
Level application example on page 40.) Because there is often a
range of ways to approach an application, other configurations may also apply.
In all examples, substitute your own application details. If the example does not apply to
your application, check the applicable parameter reference for the available options.
Notes:
• This product is intended for use in industrial areas. Operation of this equipment in a
residential area may cause interference to several frequency based
communications.
• Please follow the installation and operating procedures for a quick, trouble-free
installation and to ensure the maximum accuracy and reliability of your SITRANS LR560.
• This manual applies to the SITRANS LR560 (FOUNDATION™ Fieldbus)1) only.
1) FOUNDATION™Fieldbus is a trademark of Fieldbus Foundation.

Page 4 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
SITRANS LR560 (FF)
Technical Support
Support is available 24 hours a day.
To find your local Siemens Automation Office address, phone number and fax number go
to:
www.siemens.com/automation/partner
• Click on the tab Contact, select Service, then click Service again to find your
product group (+Automation Technology > +Sensor Systems >+Process
Instrumentation > +Level Measurement > +Continous). Select Radar.
• Select the country followed by the City/Region.
• Select Technical Support under Service.
For on-line technical support go to:
www.siemens.com/automation/support-request
• Enter the device name (SITRANS LR560) or order number, then click on Search,
and select the appropriate product type. Click on Next.
• You will be prompted to enter a keyword describing your issue. Then either
browse the relevant documentation, or click on Next to email a detailed
description of your issue to Siemens Technical Support staff.
Siemens IA/DT Technical Support Center: phone [phone]
Abbreviations and Identifications
Short
form Long Form Description Units
AIFB Analog Input Function Block
CE / FM /
CSA
Conformité Européenne /
Factory Mutual / Canadian
Standards Association
safety approval
DCS Distributed Control System process control
DD See EDD
DIAG TB Diagnostic Transducer
Block
dK dielectric constant
EDD Electronic Device
Description (also referred to as DD)
FF Foundation Fieldbus communication protocol
FMCW Frequency Modulated
Continous Wave radar principle

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 5
mmmmm
SITRANS LR560 (FF)
H1 31.25 kbps 2-wire fieldbus
protocol
HSE High Speed Ethernet communication protocol
ITK Interoperability Test Kit
IiInput current mA
IoOutput current mA
LAS Link Active Scheduler
LCD Liquid Crystal Display
LDI Local Display Interface removable display with push
buttons
LTB Level Transducer Block
LUI Local User Interface
view outputs via LCD display;
make modifications via push
buttons or handheld programmer
μsmicrosecond 10-6 Second
PED Pressure Equipment
Directive safety approval
PID FB Proportional Integral
Derivative Function Block
ppm parts per million
PV Primary Value measured value
RES Resource Block
SELV Safety extra low voltage
SV Secondary Value equivalent value
TVT Time Varying Threshold sensitivity threshold
UiInput voltage V
UoOutput voltage V
Short
form Long Form Description Units (cont’d)

Page 6 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
SITRANS LR560 (FF)
SITRANS LR560 Overview
SITRANS LR560 is a 2-wire, 78 GHz FMCW radar level transmitter for continuous
monitoring of solids in vessels to a range of 100 m (329 ft). The plug and play performance
is ideal for all solids applications, including those with extreme dust and high
temperatures to +200 °C (+392 °F). The device consists of an electronic circuit coupled to
a lens antenna and flange for quick and easy positioning.
The main benefits of using 78 GHz over devices using lower frequency are:
• very narrow beam, so device is insensitive to mounting nozzle interference and
vessel obstructions.
• short wavelength yields very good reflection properties on sloped solids, so aiming
towards material angle of repose is usually not necessary.
The technology is very tolerant of buildup on the lens antenna, however an air purge inlet
is provided for periodic cleaning if required.
SITRANS LR560 supports Foundation Fieldbus communication protocol, and AMS Device
Manager software. Signals are processed using Process Intelligence which has been
field-proven in over 1,000,000 applications worldwide (ultrasonic and radar). This device
can be configured as an FF (H1) Link Master.
Programming
SITRANS LR560 is very easy to install and configure via an optional graphical local
display interface (LDI). You can modify the built-in parameters either locally, using the
control buttons or the infrared handheld programmer, or from a remote location using one
of the following options:
•PROFIBUS PA [using SIMATIC PDM, or FDT (such as PACTware). See SITRANS
LR560 (PROFIBUS PA) Instruction Manual for more information.]
•HART [using handheld 375 Field Communicator, SIMATIC PDM, AMS, or FDT (such
as PACTware). See SITRANS LR560 (mA/HART) Instruction Manual for more
information.]
•Foundation Fieldbus (FF) [using handheld 375 Field Communicator, an FF host
system, or AMS].
Once programmed, the graphic Local Display Interface (LDI) can be removed if desired
and used to transfer parameters to multiple SITRANS LR560s.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 7
mmmmm
SITRANS LR560 (FF)
Local Display Interface (LDI)
• LDI may be ordered installed or added later as an
option
• can be mounted in 1 of 4 positions at 90 degree
intervals, for easy viewing after installation
• displays level and diagnostic information
including echo profile and trend over time
• backlit for easy viewing in dimly lit areas
• allows you to copy parameters from one device
to another
• provides high speed firmware transfer capabilities for future upgrades
Versions
Two different versions of the LR560 are available:
• 40 m range, 100 °C maximum process temperature
• 100 m range, 200 °C maximum process temperature
Applications
• cement powder, plastic powder/pellets, grain, flour, coal, and other applications
• solids bulk storage vessels
Approvals and Certificates
SITRANS LR560 is available with General Purpose or Hazardous approvals. For details
see
Approvals on page 10.
Application
Type
LR560
Version Approval Rating Valid for: Wiring
Non-
hazardous
General
Purpose CSAUS/C, FM, CE, C-TICK N. America,
Europe
See
page 23
Hazardous
Non-Sparking/
Energy Limited ATEX II 3G Ex nA/nL IIC T4 Gc Europe See page 28
Dust Ignition
Proof
ATEX II 1D, 1/2D, 2D
IECEx SIR 09.0149X
Ex ta IIIC T139 oC Da
Europe and
International
See
page 28
FM/CSA:
Class II, Div. 1, Groups E, F, G
Class III T4
US/Canada See
page 28
Non-incendive FM/CSA:
Class I, Div. 2, Groups A, B, C, D T4 US/Canada See page 28

Page 8 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
Specifications
Specifications
Power
Bus powered 9 to 32 V DC, per IEC 61158-2 (Foundation Fieldbus)
Current consumed 13.5 mA
Performance
Reference operating conditions according to IEC 60770-1
• ambient temperature +15 to +25 oC (+59 to +77 oF)
• humidity 45% to 75% relative humidity
• ambient pressure 860 to 1060 mbar g (86,000 to 106,000 N/m2 g)
Measurement Accuracy1) (measured in accordance with IEC 60770-1)
• Maximum measured error Greater of 25 mm (1") or 0.25% of range from
minimum detectable distance to full range
Frequency 78 to 79 GHz FMCW
Max. measurement range2)
• 40 m version 40 m (131 ft)
• 100 m version 100 m (328 ft)
Min. detectable distance 300 mm (11.8") from sensor reference point
Update time3) Maximum 10 seconds, depending on setting for
Response Rate (2.3.6.1.)
Influence of ambient temperature <0.003%/K (average over full temperature range,
referenced to maximum range)
Dielectric constant of material measured
• Minimum dK = 1.6 for ranges to 20 m (65.6 ft) range
= 2.5 for ranges to 100 m (328 ft) range
Memory
• non-volatile EEPROM
• no battery required
Notes:
• Siemens Milltronics makes every attempt to ensure the accuracy of these
specifications but reserves the right to change them at any time.
1) Reference conditions: Position Detect (2.4.5.2.) set to Center and Algorithm
(2.4.5.1.) set to True First Echo.
2) From sensor reference point.
3) Reference conditions: Response Rate (2.3.6.1.) set to FAST.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 9
mmmmm
Specifications
Interface
Communication
• Foundation Fieldbus
• ITK version 5 Blocks supported:
RESOURCE, LTB, AIFB1, AIFB2, PID, LCD, DIAG
Block execution time:
AIFB - 30 ms, PID - 100 ms
Configuration
• remote FF host system or Emerson AMS version 9.0 (PC)
• local Siemens Milltronics infrared handheld programmer
[see
Programmer (infrared keypad) on page 11],
or Field Communicator 375 [see
Field Communicator
375 (FC375)
on page 147],
or local control buttons
Optional removable
local display interface (LDI)1) graphic LCD, with bar graph representing level
Mechanical
Process Connections:
• universal flat-faced flanges2)
3"/80 mm, 4"/100 mm, 6"/150 mm
- materials stainless steel 316L (1.4404 or 1.4435), or 304
• Aimer flanges2) 3"/80 mm, 4"/100 mm, 6"/150 mm
- material polyurethane powder-coated cast aluminum
Enclosure
• construction 316L/1.4404 stainless steel
• conduit entry M20x1.5, or ½" NPT
• conduit entry connector M12 connector (shipped with M20 to M12 adaptor)
(optional) or 7/8" connector (shipped with 1/2" NPT to 7/8"
adaptor)
• ingress protection Type 4X/NEMA 4X, Type 6/NEMA 6, IP68
• lid with window polycarbonate (window material)
Lens antenna material
•construction
- 40 m version PEI
- 100 m version PEEK
1) Display quality will be degraded in temperatures below –20 °C (–4 °F) and above
+65°C (+149 °F).
2) Universal flange mates with EN 1092-1 (PN16)/ASME B16.5 (150 lb)/JIS 2220 (10K) bolt
hole pattern.

Page 10 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
Specifications
Air Purge Connection
• equipped with female 1/8" NPT fitting
Weight
• 3" stainless steel flange model 3.15 kg (6.94 lb)
Environmental
• location indoor/ outdoor
• altitude 5000 m (16,404 ft) max.
• ambient temperature −40 to +80 °C (−40 to +176 °F)
• relative humidity suitable for outdoor
Type 4, 4X/NEMA 4, 4X, Type 6/NEMA 6, IP68
enclosure (see note above)
• installation category I
• pollution degree 4
Process
• temperature and pressure1)
Approvals
•General CSA
US/C, FM, CE
• Radio R&TTE (Europe), FCC, Industry Canada, C-TICK
Note: Use appropriate conduit seals to maintain IP or NEMA rating.
Versions Stainless steel
flange
Aimer flange
0.5 bar max.
Aimer flange
3.0 bar max
40 m –40 to +100 °C
(–40 to +212 °F)
–40 to +100 °C
(–40 to +212 °F)
–40 to +100 °C
(–40 to +212 °F)
100 m –40 to +200 °C
(–40 to +392 °F)
–40 to +200 °C
(–40 to +392 °F)
–40 to +120 °C
(–40 to +248 °F)
1) Maximum and minimum process temperatures are dependent on the process con-
nection, O-ring materials, and vessel pressure. Use of the Easy Aimer limits maximum
temperature.
Note: The device nameplate lists the approvals that apply to your device.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 11
mmmmm
Specifications
• Hazardous
Non-sparking/
Energy Limited1) (Europe) ATEX II 3G Ex nA/nL IIC T4 Gc
Dust Ignition Proof 1) (Europe/International) ATEX II 1D, 1/2D, 2D
IECEx SIR 09.0149X
Ex tD A20 IP67 T100 oC
Dust Ignition Proof 2) (US/Canada) FM/CSA:
Class II, Div. 1, Groups E, F, G
Class III T4
Non-incendive 2) (US/Canada) FM/CSA Class I, Div. 2,
Groups A, B, C, D, T4
Programmer (infrared keypad)
Siemens Milltronics Infrared IS (Intrinsically Safe) Hand Programmer for hazardous and
all other locations (battery is non-replaceable)
• approval FM/CSA Class I, II, III, Div. 1, Gr. A to G T6
CE
ATEX II 1GD Ex ia IIC T4 Ga
Ex iaD 20 T135 °C
IECEx SIR 09.0073 Ex ia IIC T4 Ga
Ex iaD 20 T135 °C
INMETRO Br-Ex ia IIC T4
• ambient temperature −20 to +50 °C (−5 to +122 °F)
• interface proprietary infrared pulse signal
• power 3 V lithium battery
• weight 150 g (0.3 lb)
• color black
• Part Number 7ML1930-1BK
1) See
Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring
(Europe/International)
on page 28 for more details.
2) See
Non-incendive and Dust Ignition Proof wiring (US/Canada) on page 28
Notes:
• Battery is non-replaceable with a lifetime expectancy of 10 years in normal use.
• To estimate the lifetime expectancy, check the nameplate on the back for the serial
number. The first six numbers show the production date (mmddyy), for example,
serial number 032608101V.

Page 12 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
Specifications
Dimensions
SITRANS LR560 with stainless steel universal flat flange
1)
Notes:
• Process temperature and pressure capabilities are dependent upon information
displayed on the process device markings.
• Refer to
Universal Slotted Flange on page 16 for bolt hole pattern and dimensions.
1) Shipped with product, packed in a separate bag.
grounding
lug
purge inlet
process
connection:
flat flange
cable
gland1)
110 mm
(4.33")
176 mm
(6.93")
9.6 mm
(0.38")
lid lock
sensor
reference
point
3": 200 mm (7.87")
4": 229 mm (9.02")
6": 285 mm (11.22")
pressure-related
information
device label

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 13
mmmmm
Specifications
SITRANS LR560 with 3" Aimer Flange
Notes:
• Process temperature and pressure capabilities are dependent upon information
displayed on the process device markings.
• Refer to
Universal Slotted Flange on page 16 for bolt hole pattern and dimensions.
grounding
lug
purge
inlet
process
connection:
aimer flange
cable
gland
110 mm
(4.33")
166.1 mm
(6.54")
200 mm
(7.87")
23.3 mm
(0.92")
sensor
reference
point
lid lock
pressure-related
information
device label

Page 14 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01
mmmmm
Specifications
SITRANS LR560 with 4" and 6" Aimer Flange
C Spanner
Notes:
• Process temperature and pressure capabilities are dependent upon information
displayed on the process device markings.
• Refer to
Universal Slotted Flange on page 16 for bolt hole pattern and dimensions.
grounding
lug
purge inlet
process
connection:
aimer
flange
cable
gland
110 mm
(4.33")
166.1 mm
(6.54")
sensor
reference
point
9.6 mm
(0.38")
4": 229 mm (9.02")
6": 285 mm (11.22")
4": 53.2 mm (2.09")
6": 60.0 mm (2.36)
pressure-related
information
lid lock
device label
A C spanner, used to loosen the aimer
locking ring, is shipped with the device.