Siemens SITRANS P220 Administrator guide

1
English ............................................................................................... 3
Deutsch............................................................................................ 20
Français ........................................................................................... 37

© Siemens AG 2017. All rights reserved
A5E03304437-AA, 09/2017 3
SITRANS
Pressure transmitter
SITRANS P220 (7MF1567)
Compact Operating Instructions
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The
notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage
have no safety alert symbol. These notices shown below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of
injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific task in accordance with
the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their
training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products
and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage,
installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.
1
Introduction
1.1
Purpose of this documentation
These instructions contain all information required to commission and use the device. Read the instructions carefully prior to
installation and commissioning. In order to use the device correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it electronically, configuring the
parameters and commissioning it, as well as service and maintenance engineers.
See also
Technical support (Page 18)

SITRANS P220 (7MF1567)
4A5E03304437-AA, 09/2017
1.2
Checking the consignment
1. Check the packaging and the delivered items for visible damage.
2. Report any claims for damages immediately to the shipping company.
3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
•
Do not use damaged or incomplete devices.
1.3
Transportation and storage
To guarantee sufficient protection during transport and storage, observe the following:
●Keep the original packaging for subsequent transportation.
●Devices/replacement parts should be returned in their original packaging.
●If the original packaging is no longer available, ensure that all shipments are properly packaged to provide sufficient
protection during transport. Siemens cannot assume liability for any costs associated with transportation damages.
NOTICE
Insufficient protection during storage
The packaging only provides limited protection against moisture and infiltration.
•
Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in Technical specifications (Page 14).
1.4
Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing agreement, commitment or legal
relationship. The sales contract contains all obligations on the part of Siemens as well as the complete and solely applicable
warranty conditions. Any statements regarding device versions described in the manual do not create new warranties or
modify the existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right to make technical changes in
the course of further development.
2
Safety instructions
2.1
Prerequisites for safe use
This device left the factory in good working condition. In order to maintain this status and to ensure safe operation of the
device, observe these instructions and all the specifications relevant to safety.
Observe the information and symbols on the device. Do not remove any information or symbols from the device. Always
keep the information and symbols in a completely legible state.
Symbol
Explanation
Consult operating instructions

SITRANS P220 (7MF1567)
A5E03304437-AA, 09/2017 5
2.1.1
Laws and directives
Observe the safety rules, provisions and laws applicable in your country during connection, assembly and operation. These
include, for example:
●National Electrical Code (NEC - NFPA 70) (USA)
●Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
●IEC 60079-14 (international)
●EN 60079-14 (EC)
2.1.2
Conformity with European directives
The CE mark on the device is a sign of conformity with the following European directives:
Electromagnetic compatibility EMC
2014/30/EU
Directive o
f the European Parliament and of the Council on the harmonisation of the
laws of the Member States relating to electromagnetic compatibility.
Atmosphère explosible ATEX
2014/34/EU
Directive of the European Parliament and of the Council on the harmonisati
on of the
laws of the Member States relating to equipment and protective systems intended for
use in potentially explosive atmospheres.
The standards applied can be found in the EC declaration of conformity for the device.
WARNING
Improper device modifications
Risk to personnel, system and environment can result from modifications to the device, particularly in hazardous areas.
•Only carry out modifications that are described in the instructions for the device. Failure to observe this requirement
cancels the manufacturer's warranty and the product approvals.
2.2
Requirements for special applications
Due to the large number of possible applications, each detail of the described device versions for each possible scenario
during commissioning, operation, maintenance or operation in systems cannot be considered in the instructions. If you need
additional information not covered by these instructions, contact your local Siemens office or company representative.
Note
Operation under special ambient conditions
We highly recommend that you contact your Siemens representative or our application department before you operate the
device under special ambient conditions as can be encountered in nuclear power plants or when the device is used for
research and developm
ent purposes.
2.3
Use in hazardous areas
Qualified personnel for hazardous area applications
Persons who install, connect, commission, operate, and service the device in a hazardous area must have the following
specific qualifications:
●They are authorized, trained or instructed in operating and maintaining devices and systems according to the safety
regulations for electrical circuits, high pressures, aggressive, and hazardous media.
●They are authorized, trained, or instructed in carrying out work on electrical circuits for hazardous systems.
●They are trained or instructed in maintenance and use of appropriate safety equipment according to the pertinent safety
regulations.

SITRANS P220 (7MF1567)
6A5E03304437-AA, 09/2017
WARNING
Use in hazardous areas
Risk of explosion.
•Only use equipment that is approved for use in the intended hazardous area and labelled accordingly.
See also
Technical specifications (Page 14)
WARNING
Loss of safety of device with type of protection "Intrinsic safety Ex i"
If the device has already been operated in non-intrinsically safe circuits or the electrical specifications have not been
observed, the safety of the device is no longer ensured for use in hazardous areas. There is a risk of explosion.
•Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe circuit.
•Observe the specifications for the electrical data on the certificate and/or in Technical specifications (Page 14).
3
Description
3.1
Application
The pressure transmitter P220, Type 7MF1567, is used for measuring the relative pressure and absolute pressure of gases
and liquids in the following industrial areas:
●Mechanical engineering
●Power engineering
●Water supply
●Shipbuilding
●Chemical industry
●Pharmaceuticals
3.2
Hardware configuration
7MF1567 with plug complying with EN 175301-803-A
•
Type 7MF1567-*****-1**1
•
Type 7MF1567-*****-5**1
7MF1567 with plug M12x1
•
Type 7MF1567-*****-2**1

SITRANS P220 (7MF1567)
A5E03304437-AA, 09/2017 7
7MF1567 with cable (2 m)
•
Type 7MF1567-*****-3**1
7MF1567 with fast-fit cable gland
•
Type 7MF1567-*****-4**1
Device structure without explosion protection
The pressure transmitter consists of a piezo-resistive measuring cell with a diaphragm installed in a stainless steel
enclosure. It can be electrically connected using a plug complying with EN 175301-803-A (IP65), a round plug M12 (IP67), a
cable (IP67) or a fast-fit cable gland (IP67). The output signal is between 4 and 20 mA or 0 and 10 V.
Device structure with explosion protection
The pressure transmitter consists of a piezo-resistive measuring cell with a diaphragm installed in a stainless steel
enclosure. It can be connected electrically with a connector fulfilling EN 175301-803-A (IP65) or a round plug M12 (IP67).
The output signal amounts to between 4 and 20 mA.
3.3
Layout of the nameplate
*) Decoding for year, month and day information
Code
Year
A
2010
B
2011
C
2012
D
2013
E
2014
F
2015
H (G)
1)
2016
J
2017

SITRANS P220 (7MF1567)
8A5E03304437-AA, 09/2017
Code
Year
K
2018
L
2019
M
2020
N
2021
P
2022
R
2023
S
2024
T
2025
U
2026
V
2027
W
2028
X
2029
Code
Month
1
January
2
February
3
March
4
April
5
May
6
June
7
July
8
August
9
September
O
October
N
November
D
December
Code
01-31
Day of month
1st to 31st day
1) Conforming to DIN EN 60062
2) The letter G is not permitted for new applications since it deviates from DIN EN 60062. It serves only for coding back.
4
Installing/mounting
4.1
Basic safety instructions
CAUTION
Direct sunlight
Device damage.
The device can overheat or materials become brittle due to UV exposure.
•Protect the device from direct sunlight.
•Make sure that the maximum permissible ambient temperature is not exceeded. Refer to the information in Technical
specifications (Page 14).

SITRANS P220 (7MF1567)
A5E03304437-AA, 09/2017 9
WARNING
Wetted parts unsuitable for the process media
Risk of injury or damage to device.
Hot, toxic and corrosive media could be released if the process medium is unsuitable for the wetted parts.
•Ensure that the material of the device parts wetted by the process medium is suitable for the medium. Refer to the
information in Technical specifications (Page 14).
Note
Material compatibility
Siemens can provide you with support concerning selection of sensor components wetted by process media. However, you
are responsible for the selection of components. Siemens accepts no liability for faults or failures resulting from incompatible
materials.
WARNING
Exceeded maximum ambient or process media temperature
Danger of explosion in hazardous areas.
Device damage.
•Make sure that the maximum permissible ambient and process media temperatures of the device are not exceeded.
Refer to the information in Technical specifications (Page 14).
4.2
Additional notes on installation of explosion protection devices
The following specifications are to be observed for the types
7MF1567-***01-1**1
,
7MF1567-***01-2**1
, and
7MF1567-
***01-5**1
:
Operation is permitted only when connected to certified intrinsically-safe resistive circuits with the following maximum values:
U
i
≤30 V
I
i
≤100 mA
Pi≤750 mW
Internal inductance Li = 0 nH
Internal capacitance Ci = 0 nF
A maximum ambient air temperature Taof -25 °C to +85 ºC is permitted for the pressure transmitter.
Use as a resource belonging to Category 1/2:
The pressure transmitters can be mounted in the wall separating the area with Category 1 requirements (Zone 0) and the
area with Category 2 requirements (Zone 1). In this case, the process connection must be adequately sealed in compliance
with IEC/EN 60079-26, Clause 4.3, for example by providing degree of protection IP67 in compliance with EN60529. The
supply must be effected via intrinsically safe circuits with type of protection ia. The measuring cell may only be used for
flammable materials to which the diaphragms of the measuring cells are adequately resistant both chemically and in terms of
corrosion.
4.3
Installation
●The location of the device has no influence on the measurement accuracy.
●Before installation, compare the process data with the data of the rating plate.
●The medium being measured must be suitable for the parts of the pressure transmitter in contact with the medium.
●The overload limit must not be exceeded.
●Connect the devices with fixed cable installation.

SITRANS P220 (7MF1567)
10 A5E03304437-AA, 09/2017
5
Connecting
5.1
Basic safety instructions
WARNING
Unsuitable cables, cable glands and / plug-in connectors
Danger of explosion in hazardous areas.
•Only use cable glands/plug-in connectors that fulfill the requirements of the relevant type of protection.
•Only use cables that have been designed for an ambient temperature of at least 20 K higher.
•Close cable openings for electrical connections that are unused.
•When replacing cable glands, only use ones of the same type.
•
After installation check that the cables are seated firmly.
WARNING
Improper power supply
Risk of explosion in hazardous areas as result of incorrect power supply, e.g. using direct current instead of alternating
current.
•Connect the device in accordance with the specified power supply and signal circuits. The relevant specifications can
be found in the certificates, in Technical specifications (Page 14) or on the nameplate.
WARNING
Unsafe extra-low voltage
Risk of explosion in hazardous areas due to voltage flashover.
•
Connect the device to an extra-low voltage with safe isolation (SELV).
5.1.1
Grounding for Ex (explosion protection) devices
WARNING
Lack of equipotential bonding
Danger of explosion through compensating currents or ignition currents through lack of equipotential bonding.
•Make sure that equipotential bonding exists for the device.
•The pressure transmitter must be connected to the equipotential bonding system of the plant via the metal housing
(process connection) or the ground conductor of the plug.
Exception:
It may be permissible to omit connection of the equipotential bonding for devices with type of protection
"Intrinsic safety Ex i".
WARNING
Unprotected cable ends
Risk of explosion through unprotected cable ends in hazardous areas.
•
Protect unused cable ends in accordance with IEC/EN 60079-14.