Siemens TRANSMAG 2 User manual

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/104 Siemens FI 01 · 2014
■ Overview
SITRANS F M TRANSMAG 2 with the SITRANS FM 911/E sensor
is a pulsed alternating field magnetic flowmeter where the mag-
netic field strength is much higher than conventional DC pulsed
magnetic flowmeters.
■ Benefits
• Wide range of sizes DN 15 to DN 1000 (½" to 40")
• Broad range of liner and electrode materials for extreme pro-
cess medias
• Fully welded construction provides a ruggedness that suits
the toughest applications and environments.
• Automatic reading of SmartPLUG for easy commissioning
• Simple menu operation with two-line display
• Comprehensiv self-diagnostic with selfmonitoring and internal
simulation
■ Application
The main applications of the SITRANS F M transmitter
TRANSMAG 2 can be found in the following sectors:
• Pulp and Paper industry
• Mining industry
The patented pulse alternating field technology is ideal for diffi-
cult applications like:
• High concentrated paper stock > 3 %
• Heavy mining slurries
• Mining slurries with magnetic particles.
• Low conductive medias 1 S/cm (0.1 S/cm depending on
medium)
■ Design
• Available for remote mounting
• PROFIBUS PA (profile 2.0) / HART communication
• Analog output and digital outputs for pulses, device status,
limits, flow direction, frequency output
■ Mode of operation
The flow measuring principle is based on Faraday’s law of elec-
tromagnetic induction according to which the sensor converts
the flow into an electrical voltage proportional to the velocity of
the flow.
■ Function
The TRANSMAG 2 is a microprocessor-based transmitter with a
build-in alphanumeric display in several languages. The trans-
mitters evaluate the signals from the associated electromagnetic
sensors and also fulfil the task of a power supply unit which pro-
vides the magnet coils with a constant current.
The magnetic flux density in the sensor is additionally monitored
by reference coils.
Further information on connection, mode of operation and instal-
lation can be found in the data sheets for the sensors.
Displays and keypad
Operation of the transmitter can be carried out using:
• Keypad and display unit
• HART communicator
• PC/laptop and SIMATIC PDM software via HART communica-
tion
• PC/laptop and SIMATIC PDM software using PROFIBUS PA
communication
HART communication
PROFIBUS PA communication
Operating and
display panel
PC/
laptop
Coupling
module
HART
communicator RS 232
min. 230 Ω
Transmitter with
PROFIBUS PA interface
Coupler with
power supply
Bus
term.
Master
PROFIBUS DP PROFIBUS PA
.......
T
+
FI01_2014_en_Kap03.book Seite 104 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/105
Siemens FI 01 · 2014
■ Technical specifications
Transmitter TRANSMAG 2
Mode of operation and design
Measuring principle Electromagnetic with pulsed
alternating field (PAC)
Magnetic field excitation Automatic power supply syn-
chronization
- 50 Hz AC power supply Bipolar (16.7 Hz)
Bipolar with prepulse (10 Hz)
Unipolar (8.33 Hz)
- 60 Hz AC power supply Bipolar (20 Hz)
Bipolar with prepulse (12 Hz)
Unipolar (10 Hz)
Accuracy under reference
conditions
Measuring tolerance of pulse output
• With v > 0.25 m/s (0.82 ft/s) 0.5 % of measured value
1.2 mm/s (0.05 inch/s)
• With v < 0.25 m/s (0.82 ft/s) 2.5 mm/s (0.1 inch/s)
Measuring tolerance of analog out-
put As pulse output plus 0.1 % conversion error 20 µA
Repeatability 0.2 % of measured value
Reference conditions
• Process temperature 25 °C 5°C(77°F9°F)
• Ambient temperature 25 °C 5°C(77°F9°F)
• Warm-up time Min. 30 min
• Installation conditions Inlet pipe section 10 x DN
Outlet pipe section 5 x DN
Installed centered in pipe
•Medium Water without gaseous or solid
components
Calibration
Standard production calibration,
calibration report shipped with sen-
sor
Zero-point, 2 x 25 % and 2 x 90 %
Output
Electrical isolation Outputs electrically isolated from
one another and from the power
supply, max. 60 V permissible
against PE/equipotential bonding
Current output 0/4 ... 20 mA
(7ME5034-0…. or 7ME5034-2….)
•Signal
- Upper limit 0/4 … 20 mA, selectable
- Failure 20 … 22.5 mA,
optional 3.6; 20 or 24 mA
•Load
-Output max. 600 , max. load voltage
15 V DC
- For HART communication 250 
Communication Via analog output with PC cou-
pling module or HART communi-
cator
•Protocol HART, version 5.1
Digital output
Signal
•Output Configurable as active or passive
signals
- Active signal 24 V DC, 24 mA, R
i
= 170 
- Passive signal Open collector, max. 30 V DC,
200 mA
Output configuration
•Pulse
- Pulse significance 5000 pulses/s
-Pulsewidth 0.1 ms
• Limit frequency 10000 Hz
• Limits Limits for flow and quantity, flow
direction, alarm
Digital output 2 (relay)
(only 7ME5034-0.…)
Relay NC or NO function
•Rating Max. 5 W, max. 50 V AC/DC,
max. 200 mA
• Output configuration Limits for flow and quantity, flow
direction, alarm
Digital input (optional to digital
output 2)
(only 7ME5034-2.…)
• Input function configurable as
high-active or low-active Set measured value or counter to zero
• Signal voltage Max. 30 V DC, R
i
= 3 k:
High level: +11 ... +30 V DC
Low level: -30 ... +5 V DC
For PROFIBUS devices
PROFIBUS PA (for
PROFIBUS-devices 7ME5034-1….)
• Communication Layer 1 and 2 according to
PROFIBUS PA
Transmission according to
IEC 1158-2
Layer 7 (protocol layer) according
to PROFIBUS PA and DP V1
(EN 50170)
Device class B, device profile 2.0
Max. 4 simultaneous C2 connec-
tions
• Bus voltage 9 ... 32 V DC permissible
• Current consumption from bus 10 mA; limited to 15 mA in event
of fault by electrical current limita-
tion
Rated operating conditions
Installation conditions See also sensor
Ambient temperature
• Operation -20 ... +60 °C (-4 ... +140 °F)
• Display module 0 ... 50 °C (32 ... 122 °F)
Storage -25 ... +80 °C (-13 ... +176 °F)
Degree of protection IP67/NEMA 4X
Electromagnetic compatibility
(EMC)
• Emitted interference To IEC/EN 61326 for use in
industrial areas
• Noise immunity To IEC/EN 61326 for use in
industrial areas
FI01_2014_en_Kap03.book Seite 105 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/106 Siemens FI 01 · 2014
Sensor cables between sensor and transmitter
The signal voltage proportional to the flow and present at the
electrodes of the EMF is only a few µV to mV. Superimposed on
this are electrochemical interferences resulting from the contact
between the electrodes and liquid, and which can be up to sev-
eral Volt. Also frequently superimposed are line frequency inter-
ferences, interferences resulting from vibrations on the pipelines
or signal cables, as well as strong magnetic fields in the vicinity.
Sufficient shielding must therefore be provided, as well as fixed
routing of the signal cables (electrode and magnet current ca-
ble) in the case of remote versions. This also applies to devices
with integral preamplifier (smartPLUG). The cable length be-
tween the sensor and transmitter must not exceed 100 m
(328 ft).
Attention must also be paid to the cable routing. Signal cables
must be routed free of vibration, and protected against strong
magnetic and stray fields. In case of doubt, the sensor cables
must be routed in earthed steel conduit.
Operating instructions for SITRANS F M TRANSMAG 2
This device is shipped with a Quick Start guide and a CD containing fur-
ther SITRANS F literature.
All literature is also available for free at:
http://www.siemens.com/flowdocumentation
Medium conditions
• Process temperature -20 ... +150 °C (-4 ... 302 °F)
depending on the liner
Minimum conductivity of medium
• With SITRANS F M 911/E sensors 1 µS/cm (0.1 µS/cm depending
on medium)
Design
Weight of transmitter 4.4 kg (9.7 lb)
Remote version Transmitter must be connected to
sensor using shielded cable
Maximum cable length 100 m (328 ft)
Housing Die-cast aluminum, painted
Displays and keypad
General display LCD, backlid, two lines with
16 characters each
Multi-display for Flow, totalizer, flow velocity
Keypad 4 keys for entering parameters
Power supply
corresponding to rating plate
•ACsupply 100 ... 250 V AC 15 %,
47 ... 63 Hz
• Power consumption Approx. 120 ... 630 VA, depend-
ing on sensor
Line fuse 100 ... 230 V AC: T1.6A
Magnet current fuse F5A/250 V
Selection and Ordering data Article No.
SITRANS F M electromagnetic
transmitter TRANSMAG 2
for alternating field, remote version,
110 ... 230 V AC
7 ME 5 0 3 4 -
7
A A
7
1 -
7
A A 0
Output/communication
4 ... 20 mA with HART protocol 0
PROFIBUS PA connection 1
4 ... 20 mA with HART protocol,
digital input 2
Operator display and keypad
Without 0
With 1
Cable glands
M20/M16 x 1.5 1
½“ NPT 2
Selection and Ordering data Order code
Additional information
Please add “-Z“ to Article No. and specify Order
code(s) and plain text.
Strengthened mounting bracket for wall and pipeline
installation A02
Measuring range, specify in plain text:
Y01: 0 to ... m
3
/h Y01
Pulse significance, specify in plain text:
Y02: 0 to ... pulses/l Y02
Setting of digital outputs, specify in plain text:
Y03: Setting of digital outputs: ... Y03
Measuring-point number (max. 8 characters), specify in
plain text: Y15: .......... Y15
Measuring-point description (max. 16 characters),
specify in plain text: Y16: .......... Y16
Stainless steel tag plate Y17
Other post-production requirements (add plain text) Y99
Description Article No.
• English A5E00102775
•German A5E00192774
• Spanish A5E00135276
•French A5E00135275
FI01_2014_en_Kap03.book Seite 106 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/107
Siemens FI 01 · 2014
Accessories
¢We can offer shorter delivery times for configurations designated with
the Quick Ship Symbol ¢. For details see page 9/5 in the appendix.
Spare parts
Description Article No.
Standard wall mounting
bracket. Steel AISI 316L/
EN10088-2-1.4404
7ME5933-0AC04
Special wall-/pipe mount-
ing bracket kit. BI 2,5
DIN59382 X6Cr17
7ME5933-0AC05
Potting kit for terminal box
of flow sensors for
IP68/NEMA 6P (not for Ex
sensors)
¢FDK:085U0220
Description Article No.
Operating/Display module 7ME5933-0AC00
Electronics cover with glass
plate (non Ex). Die cast alu-
minum, with corrosion-resis-
tant Basic Polyester powder
coating (min. 60 m)
7ME5933-0AC01
Cover for sensor cable and
gasket. Die cast aluminum,
with corrosion-resistant
Basic Polyester powder
coating (min. 60 m)
7ME5933-0AC02
Cover for mains
supply/communication. Die
cast aluminum, with corro-
sion-resistant Basic Polyes-
ter powder coating
(min. 60 m)
7ME5933-0AC03
Safety clamp for electronic
cover with glass plate
(7ME5933-0AC01)
7ME5933-0AC06
M20 cable gland set for
power and output connec-
tion, gray PA plastic, 2 pcs.
• cables Ø 6 ... 12 mm
(0.24" ... 0.47")
• -40 ... +100 °C
(-40 ... +212 °F)
A5E02246350
1/2" NPT cable gland set for
power and output connec-
tion, gray PA plastic, 2 pcs.
• cables Ø 6 ... 12 mm
(0.24" ... 0.47")
• -40 ... +100 °C
(-40 ... +212 °F)
A5E02246396
M16 x 1.5 cable gland set for
sensor connection, brass
chrome, 2 pcs. and
2 pcs. blind
•cablesØ5...9mm
(0.20" ... 0.35")
• -20 ... +105°C
(-4 ... +221 °F)
A5E02246369
FI01_2014_en_Kap03.book Seite 107 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/108 Siemens FI 01 · 2014
■ Dimensional drawings
SITRANS F M transmitter TRANSMAG 2 with wall mounting bracket,
dimensions in mm (inch)
SITRANS F M transmitter TRANSMAG 2 with wall and pipeline
mounting bracket, dimensions in mm (inch)
■ Schematics
SITRANS F M transmitter TRANSMAG 2, connection diagram
90
(3.54)
70
(2.76)
90
(3.54)
95 (3.74) 150 (5.91)
154 (6.06) Ø80 (3.15)
92 (3.62)
205 (8.07) 153 (6.02)
150 (5.91)
105 (4.13)
248 (9.76)
89 (3.50)
66
55
66
55
24
23
24
23
30
22
29
30
22
29
7
6
5
7
6
5
6
5
8
7
8
7
6
5
8
7
2
1
Digital output 1
active 24 V DC max. 24 mA Ri 170 Ω
(active/passive)
Passive open collector max. 30 V DC 200 mA
0/4 ... 20mA
Load 600 Ω
max. 15 V
Digital output 1
Passive open
collector
max. 30 DC
100 mA
Power supply
Transmitter
Power supply L/N
PE conductor
Sensor
Sensor connection
Digital output 2 (Relay)
NC/NO max. 5W, 50 V DC, 200 mA or
Digital input
High +11 ... +30 V DC
Low -30 ... +5 V DC
green/yellow
white
brown
Ref. 2
Ref. 1
Reference coil
Electr. 2 (EL 2)
Electr. 1 (EL 1)
Electrode connect
Supply (+6V)
Ground (0V)
Supply (-6V)
SmartPlug connect
PE
Magnetic fieldcorrent 2
Magnetic fieldcorrent 1
Coil cable
blue
red/orange
green
yellow
black/gray
white
brown
100 ... 230 V AC ±15%
47-63 Hz
PROFIBUS
FI01_2014_en_Kap03.book Seite 108 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/109
Siemens FI 01 · 2014
Important:
The rings must be ordered together with the sensor.
In case of replacement please include the sensor MLFB code on
the order.
911/E sensor
Process connection
Nominal diameters DN 15 ... 1000 (½" ... 40")
Metering tube connections EN 1092-1, ANSI B16.5, others on
request
Rated operating conditions
Installation conditions See system information
• Soft rubber liner 0 ... 70 °C (32 ... 158 °F)
• Hard rubber liner 0...90°C(32...194°F)
Option: 100 °C (212 °F)
• PTFE liner • -20 ... +150 °C (-4 ... +302 °F)
at 25 bar (363 psi)
• -20 ... +100 °C (-4 ... +212 °F)
at 40 bar (580 psi)
• Linatex (rubber) liner -40 ... +70 °C (-40 ... +158 °F) (for
temperatures below -20 °C (-4 °F)
AISI 316L/1.4404 flanges must be
used)
• Novolak liner 130 °C (266 °F) at 40 bar (580 psi)
Degree of protection IP67/NEMA 4X
Optional IP68/NEMA 6
Medium conditions
Maximum flow velocity 12 m/s (39.4 ft/s)
Full scale value of flow velocity 0.15 ... 12 m/s (0.49 ... 39.4 ft/s)
Design
Weight See dimensional drawings
Flange and housing material Mild steel (1.0460/1.0570, with
corrosion resistant two compo-
nent epoxy coating (min. 150 m)
or
AISI 316Ti/1.4571 flanges and car-
bon steel housing, with corrosion-
resistant two-component epoxy
coating (min. 150 m)
Measuring pipe material Stainless steel AISI 316Ti/1.4571
Electrode material • AISI 316Ti/1.4571
• PTFE: Hastelloy C276/2.4819
• Platinum head
• Titanium
• Tantalum
Grounding electrode material Defined via the Order code
Protection rings for liners
Function To protect the edges of liners from
abrasion (e.g. gravel, sand etc.).
Used mainly with soft rubber liners
and for PTFE liners at high
temperatures from 100 to 150 °C
(212 to 302 °F).
Contact with
medium Yes, please always check resistance to measured medium.
Material Stainless steel AISI 316Ti/1.4571,
optionally Hastelloy C276/2.4819
Material thickness The overall length of the sensor is
increased by
•6 mm for DN 15 to DN 150
(0.24“ for ½“ to 6“) or
•10 mm for DN 200 to DN 600
(0.4“ for 8“ to 24“)
Standard No, optional for PTFE and soft rubber
liners. They are required for PTFE lin-
ers of PN 16 (MWP 232 psi) or more
instead of protection washers, and
must be ordered separately.
Article No. 7ME5912-....
Earthing washers
Function Electrical reference and earthing of
the medium. Required if the pipelines
are not electrically conducting or are
lined (plastic pipelines, concrete
pipelines etc.). All earthing rings must
be connected to the earthing screw
present on the sensor.
Contact with
medium Yes, please always check resistance to measured medium.
Material Stainless steel AISI 316Ti/1.4571 or
Hastelloy C4/2.4610
Material thickness The overall length of the sensor is
increased by 2 mm (0.08“) per
earthing ring.
Standard No, only optional. Required between
the medium and sensor for equipo-
tential bonding between non-con-
ducting pipelines or lined pipelines.
Article No. 7ME5902-....
FI01_2014_en_Kap03.book Seite 109 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/110 Siemens FI 01 · 2014
Notes on pressure equipment directive
The devices are designed for liquids of danger group "Gases of
fluid group 1". The categories differ according to the version,
and are listed in the table below.
The minimum temperature is defined at -10 °C (14 °F) for the
flange materials C22.8 (1.0460).
The minimum temperature is defined at -20 °C (-4 °F) for the
flange material 1.4571/316Ti. For further information on the PED
standard and requirements, see page 9/6.
Classification according to pressure equipment directive (PED 97/23/EC)
Nominal diameter Nominal pressure Permissible media Category
DN (inch) PN (MWP psi)
15 ... 25 (½" ... 1") 40 (580) Gases fluid group 1 and liquids fluid group 1 Article 3.3
200 ... 300 (8" ... 12") 10 (145) Gases fluid group 1 and liquids fluid group 1 II
65 ... 250 (2½" ... 10") 16 (232) Gases fluid group 1 and liquids fluid group 1 II
40 ... 100 (1½" ... 4") 40 (580) Gases fluid group 1 and liquids fluid group 1 II
350 ... 1000 (14" ... 40") 10 (145) Gases fluid group 1 and liquids fluid group 1 III
300 ... 1000 (12" ... 40") 16 (232) Gases fluid group 1 and liquids fluid group 1 III
200 ... 600 (8" ... 24") 25 (363) Gases fluid group 1 and liquids fluid group 1 III
125 ... 600 (5" ... 24") 40 (580) Gases fluid group 1 and liquids fluid group 1 III
FI01_2014_en_Kap03.book Seite 110 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/111
Siemens FI 01 · 2014
Selection and Ordering data Article No.
Flowsensor SITRANS F M 911/E 7 M E 5 6 1 0 -
77777-7A A 7
Nominal diameter
DN 15 (½") 1 V
DN 25 (1") 2 D
DN 40 (1½") 2 R
DN 50 (2") 2 Y
DN 65 (2½") 3 F
DN 80 (3") 3 M
DN 100 (4") 3 T
DN 125 (5") 4 B
DN 150 (6") 4 H
DN 200 (8") 4 P
DN 250 (10") 4 V
DN 300 (12") 5 D
DN 350 (14") 5 K
DN 400 (16") 5 R
DN 450 (18") 5 Y
DN 500 (20") 6 F
DN 600 (24") 6 P
DN 700 (28") 6 Y
DN 750 (30") 7 D
DN 800 (32") 7 H
DN 900 (36") 7 M
DN 1000 (40") 7 R
Flange norm and pressure rating
EN 1092-1, PN 10 (DN 200 ... 1000 (8" ... 40")) B
EN 1092-1, PN 16 (DN 65 ... 1000 (2½" ... 40")) C
EN 1092-1, PN 25 (DN 200 ... 600 (8" ... 24")) E
EN 1092-1, PN 40 (DN 15 ... 600 (½" ... 24")) F
ANSI B16.5, Class 150 (½" ... 24"), max 19.6 bar
(285 psi) at 20 °C (68 °F) J
ANSI B16.5, Class 300 (½" ... 24"), max 51.1 bar
(741 psi) at 20 °C (68 °F)
K
AWWA C-207 Class D (28" ... 40") L
JIS 10 K (½" ... 24") R
Flange material
Mid steel flanges 1.0460/1.0570 1
Stainless steel flanges, AISI 316L/1.4404 3
Liner material
Soft rubber 1
PTFE (without protection washers) 3
Hardrubber 4
Linatex 5
Novolak (sealing material FFKM) 6
Electrode material
AISI 316Ti/1.4571 1
Hastelloy C276/2.4819 2
Platinum head with shaft AISI 316Ti/1.4571 3
Titanium 4
Tantalum 5
Cable glands/terminal box
Metric: Polyamide terminal box 1
½" NPT: Polyamide terminal box 2
Selection and Ordering data Order Code
Additional information
Please add “-Z“ to Article No. and specify Order
code(s) and plain text.
Two earthing (grounding) electrodes made of
stainless steel AISI 316Ti/1.4571
A02
Two earthing (grounding) electrodes made of
Hastelloy C276/2.4819 A04
Two earthing (grounding) electrodes made of Platinum
head
A05
Two earthing (grounding) electrodes made of Titanum A06
Two earthing (grounding) electrodes made of Tantalum A07
Factory certificate to EN 10204-2.2 C14
Acceptance test B to DIN 50049, section 3.1 and
EN 10204 C16
Tag name plate, stainless steel, add plain text Y17
Other postproduction requirements, add plain text Y99
Selection and Ordering data Article No. Order code
SITRANS F M TRANSMAG 2 and
sensor 911/E
7 ME 5 9 3 0 -
Cable 5
7
A 0 0 - 0 A A 0
777
Cable kit for sensor 911/E with alternating
field, Magnet current cable 3 x 1.0 mm
2
(3 x 0.0016 inch
2
), electrode/reference
cable 7 x 0.5 mm
2
(7 x 0.0008 inch
2
) with
shield PVC
• Length: 5 m (16.4 ft) B
• Length: 10 m (32.8 ft) C
• Length: 20 m (65.6 ft) D
• Length: 30 m (98.4 ft) E
• Specify other length: in plain text Z J 1 Y
FI01_2014_en_Kap03.book Seite 111 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/112 Siemens FI 01 · 2014
Selection and Ordering data Article No. Order code
SITRANS F M
electromagnetic flowmeter
Protection rings for flow sensor 911E
(per pair)
7 ME 5 9 1 2 - 7777 777
Liner
Hard rubber/soft rubber 1
Novolak 7
PTFE 0
Nominal diameter
for PTFE, mat. no. 1.4571/316 Ti
DN 15 (½") A A
DN 25 (1") C A
DN 40 (1½") E A
DN 50 (2") F A
DN 65 (2½") GA
DN 80 (3") H A
DN 100 (4") J A
DN 125 (5") K A
DN 150 (6") L A
DN 200 (8") MA
DN 250 (10") N A
DN 300 (12") P A
Other nominal diameters:
specify in plain text Z A J 1 Y
for Hard/Soft rubber, Novolak, mat. no.
1.471/316 Ti
DN 15 (½") A B
DN 25 (1") C B
DN 40 (1½") E B
DN 50 (2") F B
DN 65 (2½") GB
DN 80 (3") H B
DN 100 (4") J B
DN 125 (5") K B
DN 150 (6") L B
DN 200 (8") MB
DN 250 (10") N B
DN 300 (12") P B
Other nominal diameters:
specify in plain text Z B J 1 Y
Flange design
Flange to DIN 1
Flange to ANSI 2
Flange to JIS 3
Selection and Ordering data Article No. Order code
SITRANS F M
electromagnetic flowmeter
Earthing rings for flow sensor 911E
(per unit)
7 ME 5 9 0 2 - 7777 777
Liner
Hard rubber/soft rubber 1
Novolak 7
PTFE 0
Nominal diameter
Mat. no. 1.4571/316 Ti
DN 15 (½") A A
DN 25 (1") C A
DN 40 (1½") E A
DN 50 (2") F A
DN 65 (2½") GA
DN 80 (3") H A
DN 100 (4") J A
DN 125 (5") K A
DN 150 (6") L A
DN 200 (8") MA
DN 250 (10") N A
DN 300 (12") P A
DN 350 (14") QA
DN 400 (16") R A
DN 500 (20") S A
DN 600 (24") T A
DN 700 (28") U A
DN 800 (32") V A
DN 900 (36") WA
DN 1000 (40") X A
Other nominal diam.: specify in plain text Z A J 1 Y
Material Hastelloy C4/2.4610
DN 15 (½") A B
DN 25 (1") C B
DN 40 (1½") E B
DN 50 (2") F B
DN 65 (2½") GB
DN 80 (3") H B
DN 100 (4") J B
DN 125 (5") K B
DN 150 (6") L B
DN 200 (8") MB
DN 250 (10") N B
DN 300 (12") P B
DN 350 (14") QB
DN 400 (16") R B
DN 500 (20") S B
DN 600 (24") T B
Other nominal diam.: specify in plain text Z B J 1 Y
Flange design
Flange to DIN 1
Flange to ANSI 2
Flange to JIS 3
FI01_2014_en_Kap03.book Seite 112 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
icenta Controls Ltd
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk

Flow Measurement
SITRANS F M
Transmitter TRANSMAG 2 with sensor 911/E
3/113
Siemens FI 01 · 2014
■ Dimensional drawings
SITRANS F M flow sensor 911/E, remote version, dimensions in mm (inch)
Build-in length 911/E [in mm and inch]
1)
Tolerance for build-in lenght: L + 0.0/-4.0 mm (+0.00/-0.157 inch)
With protection rings for > DN25 + 6.0 mm, > DN200 + 10.0 mm (> 1” + 0.236 inch, > 8” + 0.394 inch)
155 (6.1)
D1
L
B
D
131 (5.16)
A
Nominal diameter DN 15 DN 25 DN 40 DN 50 DN 65 DN 80 DN 100 DN 125 DN 150 DN 200 DN 250
½“ 1“ 1 ½“ 2“ 2 ½“ 3“ 4“ 5“ 6“ 8“ 10“
Build-in length L
1)
Hard rubber version
Linatex/soft rubber version 270
(10.63) 330 (12.99) 340 (13.39) 370 (14.57) 410 (16.14) 470 (18.50)
PTFE-liner without protection rings 270
(10.63) 330 (12.99) 340 (13.39) 370 (14.57) 410 (16.14) 470 (18.50)
Novolak-version -275
(10.83) 325 (12.79) 335 (13.19) 333 (13.11) 362 (14.25) 401 (15.79) 460 (18.11)
Dimensions of sensor housing
Housing width B 170 (6.69) 240 (9.45)
Height A 206 (8.11) 222
(8.74) 229 (9.02) 262 (10.32) 274 (10.79) 286 (11.26) 299 (11.78) 334 (13.15) 358 (14.10)
Housing diameter D
1
135
(5.35) 167 (6.58) 182 (7.17) 247 (9.73) 272 (10.71) 296 (11.65) 322 (12.68) 392 (15.43) 440 (17.32)
Weight of PN16 version in kg
(MWP 232 psi version in lb) approx. 8.0
(17.64) 8.5 (18.74) 11.5 (25.35) 25.0 (55.12) 26 (57.32) 27 (59.53) 28 (61.73) 34 (74.95) 38 (83.78) 68 (149.9) 81 (178.6)
Nominal diameter DN 300 DN 350 DN 400 DN 450 DN 500 DN 600 DN 700 DN 750 DN 800 DN 900 DN 1000
12“ 14“ 16“ 18“ 20“ 24“ 28“ 30“ 32“ 36“ 40“
Build-in length L
1)
Hard rubber version
Linatex/soft rubber version 500
(19.68) 550 (21.65) 600 (23.62) 650 (25.59) 650 (25.59) 780 (30.71) 910 (35.83) 1040 (40.95) 1170 (46.06) 1300 (51.18)
PTFE-liner without protection rings 500
(19.68) 550 (21.65) 600 (23.62) 660 (25.98) 650 (25.59) 780 (30.71) -
Novolak-version 489
(19.25) 538 (21.18) 592 (23.31) 638 (25.12) 638 (25.12) 772 (30.39) 903 (35.55) 1033 (40.63) 1163 (45.79) 1293 (50.91)
Dimensions of sensor housing
Housing width B 240
(9.45) 225 (8.86) 250 (9.84) 270 (10.63) 300 (11.81) 360 (14.17) 420 (16.54) 500 (19.69) 560 (22.05) 620 (24.41)
Height A 383
(15.08) 375 (14.76) 400 (15.75) 433 (17.05) 453 (17.84) 505 (19.88) 558 (21.97) 590 (23.23) 608 (23.94) 658 (25.91) 713 (28.07)
Housing diameter D
1
490
(19.29) 474 (18.66) 524 (20.63) 591 (23.26) 629 (24.76) 734 (28.90) 839 (33.03) 904 (35.59) 939 (36.97) 1039 (40.91) 1150 (45.28)
Weight of PN10 Version in kg
(MWP 145 psi version in lb) approx. 95
(209.4) 118 (260.2) 161 (354.9) 185 (407.9) 233 (513.7) 401 (884.1) 420 (925.9) 450 (992.1) 500 (1102.3) 560 (1234.6) 620 (1366.9)
FI01_2014_en_Kap03.book Seite 113 Montag, 11. November 2013 4:45 16
© Siemens AG 2013
Tel: [phone] Fax: [phone]  e: [email protected] www.icenta.co.uk