Signature Hardware STONE TROUGH CONSOLE SINK User manual

1Stone Trough Console Sink Installation Instructions
STONE TROUGH CONSOLE SINK
INSTALLATION INSTRUCTIONS
CONTENTS
Console Installation
Sink Support
Undermount Sink
Semi-Recessed Sink
2
2
Backsplash 2
3
4
Vessel Sink 5
Drain Installation 6

2Stone Trough Console Sink Installation Instructions
Read entire Console Sink Installation Instructions.
Observe all local building and safety codes.
TOOLS AND MATERIALS:
Pencil
BEFORE INSTALLING INSTALLATION
CONSOLE SINK
1. Position the console legs on the oor to prepare for assembly.
Each leg has a 4-way ball joint with included set screws.
2. Attach the horizontal supports to the ball joints and tighten
the set screws.
3. Once assembled, place the sink stand against the wall and in
line with wall studs or wood blocking. Make sure the stand is
level. If needed, adjust the small screws under each leg.
4. Mount the anges to the wall with the included screws. Each
ange has three screws.
Note: Undermount sinks should be installed at this point. See the “Sink
Installation Instructions” below before continuing to Step 5. For semi-re-
cessed and vessel sinks, continue through the following steps, then install
sinks using the “Sink Installation Instructions.”
5. Apply a thin coat of silicone to the tops of the sink stand
where the vanity top will rest.
6. Carefully place the vanity top on the sink stand, center it and
allow silicone to dry for 24 hours..
SINK SUPPORT
T-shaped brackets hold the underside of the counter top to the
wall and can be used with either side supporting the counter.
We recommend installing the brackets using drywall screws and
attaching to wall studs or to a wood-blocked area.
1. Using a pencil, mark the position for the support bracket by
centering it under the vanity top and against the wall.
(For double sinks, center a bracket behind each drain cutout.)
2. Place the bracket back under the vanity top, securing the side
with silicone to the underside of the top and the other
side against the wall with drywall screws.
3. Allow silicone to dry for 24 hours.
Level
Screwdriver
Drill Silicone Sealant
INSTRUCTIONS
Unpack and inspect the product for any shipping
damages. If you nd damages, do not install.
Contact Customer Service at 1.866.855.2284. If you
need assistance or have questions while installing
your sink, contact Customer Service.
For adequate wall support, we recommend using
heavy-duty steel wall anchors and placing wood
blocking inside the wall. We recommend consulting
a professional if you are unfamiliar with installing
bathroom xtures. Signature Hardware accepts no
liability for any damage to the sink or wall, or for
personal injury during installation.
BACKSPLASH
For counters with a backsplash, apply silicone to
the backsplash's edge and wall-facing side.
Position the backsplash to the rear of the counter
and against the wall. Allow silicone to dry.

3Stone Trough Console Sink Installation Instructions
Read instructions completely before installing.
Note: Use care when lifting and installing any sink.
Place sink on a level surface with a towel or other
soft cloth beneath to prevent damage.
TOOLS AND MATERIALS:
Pencil
BEFORE INSTALLING INSTALLATION
UNDERMOUNT SINK
1. Carefully turn the vanity top over so that it rests upside-down
on a stable, cushioned surface.
2. Position the undermount sink over the sink cutout. Make sure
the sink is centered with the faucet hole and is evenly spaced
between the bolt holes.
3. Draw an outline of the sink on the vanity top.
4. Remove the sink from the vanity top and apply a generous
bead of silicone around the sink rim.
5. Carefully place the sink upside down on the vanity top,
positioning it within the outline.
6. At each of the bolt holes in the vanity top, attach the sink clips
by placing the long end of the bracket at against the sink lip.
Screw the wing bolts through the brackets and bolt holes and
tighten snugly.
7. Carefully turn the top and sink over. If needed, reposition the
sink by slightly loosening the wing bolts and adjusting the
placement. Re-tighten the bolts when nished.
8. Remove any excess silicone sealant with a damp cloth. Let
silicone dry for 24 hours.
Neutral Cure
Silicone Sealant
Damp Cloth
For counters with a backsplash, apply silicone to
the backsplash's edge and wall-facing side.
Position the backsplash to the rear of the counter
and against the wall. Allow silicone to dry.

4Stone Trough Console Sink Installation Instructions
Read instructions completely before installing.
Note: Use care when lifting and installing any sink.
Place sink on a level surface with a towel or other
soft cloth beneath to prevent damage.
TOOLS AND MATERIALS:
BEFORE INSTALLING INSTALLATION
SEMI-RECESSED SINK
1. Carefully turn the sink over to rest upside down on the vanity top.
2. Apply a continuous bead of silicone to the outer edge of the sink.
3. Turn the sink back over, placing it inside the sink cutout and
position until centered.
4. Remove any excess silicone with a damp cloth. Let silicone dry for
24 hours.
Neutral Cure
Silicone Sealant Damp Cloth

5Stone Trough Console Sink Installation Instructions
Read instructions completely before installing.
Note: Use care when lifting and installing any sink.
Place sink on a level surface with a towel or other
soft cloth beneath to prevent damage.
TOOLS AND MATERIALS:
BEFORE INSTALLING INSTALLATION
VESSEL SINK
1. Carefully place the sink upside down on the vanity top. Apply
a continuous bead of silicone to the base of the sink where it will
rest on the top.
2. Turn the sink right-side-up and position it back over the 2”
drain hole.
3. Remove any excess silicone with a damp cloth. Let silicone dry
for 24 hours.
Neutral Cure
Silicone Sealant Damp Cloth

6Stone Trough Console Sink Installation Instructions
Read instructions completely before installing.
Note: Use care when lifting and installing any sink.
Place sink on a level surface with a towel or other
soft cloth beneath to prevent damage.
TOOLS AND MATERIALS:
BEFORE INSTALLING INSTALLATION
DRAIN INSTALLATION
1. Disassemble the drain by removing the threaded tail piece,
rubber sealing gaskets, friction washer and lock nut from
the drain body.
2. Place thread sealant on the threaded section of the tail piece
and reattach to the drain body.
3. Slide the at rubber sealing gasket up the tail piece to the top
of the drain body. This gasket will create a water tight seal
between the drain ange and sink.
4. Place the drain in the drain hole in the sink.
5. On the underside of the counter, attach the tapered rubber
gasket. With the at side facing down, slide the gasket up
the threaded shank until it makes contact with the bottom of
the sink.
6. Slide the friction washer up to meet the rubber gasket.
7. Thread the lock nut onto the threaded shank. Hand-tighten
and make sure that the drain is properly aligned. When ready,
nish tightening with a basin wrench to secure the drain.
Thread Sealant Basin Wrench