SIIG CE-H21811-S1 User manual

1
Introduction
The HDMI to VGA + Audio Converter allows you to
convert digital HDMI to VGA and analog stereo audio.
Features and Benefits
• Converts HDMI source to VGA & analog audio
• Easily used with HDMI equipped system, such as
HDMI equipped desktop, notebook & ultrabook
• Supports stereo analog audio output
• Plastic housing
• Easy to install
Note: This converter doesn't support HDCP
decryption. If the HDMI source device is HDCP-
enabled, the image may not display.
Technical Specifications
• Supports up to UXGA (1600x1200@60) & WUXGA
(1920x1200@60) PC graphics output
• Bandwidth: 60Hz
• Input: 1x HDMI 19-pin female
• Output: 1x VGA HD15-pin (D-Sub); 1x stereo audio
(3.5mm jack)
• Power supply: 5V, DC
04-0843A
HDMI to VGA + Audio
Converter
Quick Installation Guide

2
PackageContents
•HDMI to VGA + Audio Converter
• HDMI cable
• Power adapter
• Quick installation guide
Layout
Figure 1: Front Panel Layout
• HDMI Input: connects to an HDMI source device
• Audio Output: connects to headphones or stereo
analog speakers
• Power Jack: connects the power adapter here
Note: The power adapter is optional but
recommended if the bus power doesn't provide
enough power.
Power
Jack
HDMI
Input
Audio
Ouput

3
Power adapter
(optional)
HDMI cable
VGA cable
3.5mm stereo
cable
HDMI source
(desktop,
notebook,
ultrabook, etc)
VGA display
(monitor,
projector, etc)
Figure 2: Rear Panel Layout
• VGA Output: connects to your VGA display
Application
VGA
Output
Figure 3
Audio device
(speaker,
headphone,
etc)

4
Hardware Installation
Please read and follow the safety guidelines to protect
yourself from possible injury and to minimize the risk of
damage to your equipment.
• Do not attempt to service the unit yourself.
• Provide proper ventilation and air circulation, do
not use near water
• Keep objects that might damage the device a safe
distance away and place the unit on a stable surface.
• Use only the power adapter that came with the unit.
• Do not use liquid or aerosol cleaners to clean the
unit. Always unplug the power to the unit before
cleaning.
1. Power off all devices that you plan to connect to this
converter.
2. ConnectyourHDMIsourceto theconverter'sHDMI
Input connector using the included HDMI cable.
3. Connect your VGA display to the converter's VGA
Output connectorusinga VGA cable (notincluded).
4. Connect the speakers to the converter's Audio
Output.
5. Plug the power adapter into the converter's Power
Jack, then plug the power adapter into a reliable
power source.
6. Turn on the display, then the HDMI source.
7. The HDMI to VGA + Audio Converter is now ready to
use.

5
Frequency Asked Questions
Q1: Is the external power supply necessary?
A1: The HDMI source device's bus power may not be
enough to power up this converter. This power
adapter is optional but recommended to supply
efficient power to the converter.
Q2: Why is there no image displayed?
A2: Make sure the HDMI source device is not HDCP
enabled/protected. Some examples of HDCP
enabled/protected HDMI source devices include
most Blu-ray players and PS3 game consoles.

6
Blank Page

7
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support has answers! Simply visit our web site
at www.siig.com and click Support. Our online support database is updated
daily with new drivers and solutions. Answers to your questions could be
just a few clicks away. You can also submit questions online and a technical
support analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty
covers the original purchaser and guarantees the product to be free of any
defects in materials or workmanship for three (3) years from the date of
purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or
product having similar features and functionality) the product if defective in
materials or workmanship. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. Please see our
web site for more warranty details.
Ifyouencounteranyproblems with this product, please follow the procedures
below.
A) If it is within the store's return policy period, please return the product to
the store where you purchased it.
B) If your purchase has passed the store's return policy period, please follow
these steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support,
then Request A Product Replacement to submit a request to SIIG RMA
or fax a request to 510-657-5962. Your RMA request will be processed, if
the product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s) and any
otheraccessoriesthatcamewith the original package must be included.
•Clearly write your RMA number on the top of the returned package.
SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted
on the outside of the shipping carton.
•You are responsible for the cost of shipping to SIIG. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground in the U.S.
and International Economy outside of the U.S. at no cost to the
customer.

HDMI to VGA + Audio Converter is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Other names used in this publication are for identification only and may be
trademarksoftheirrespectiveowners.
December, 2012 Copyright © 2012 by SIIG, Inc. All rights reserved.
PRODUCT NAME
HDMI to VGA + Audio Converter
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. Allcenteredaroundthedistributionandswitchingof A/V signals
overCAT5/6, these productsinclude matrix switches,distribution amplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providing high quality products while keeping economical and competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.