SIIG CV-009S User manual

Component/CVBS to VGA Scaler Converter
P/N: CV-009S

Safety and Notice
The CV-009S Component/CVBS to VGA Scaler Converter has been tested for conformance to
safety regulations and requirements, and has been certified for international use. However,
like all electronic equipments, the CV-009S should be used with care. Please read and follow
the safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
●Follow all instructions and warnings marked on this unit.
●Do not attempt to service this unit yourself, except where explained in this manual.
●Provide proper ventilation and air circulation and do not use near water.
●Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
●Use only the power adapter and power cords and connection cables designed for this unit.
●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
TABLE OF CONTENTS
INTRODUCTION................................................................................................................ 1
FEATURES........................................................................................................................ 1
PACKAGE CONTENTS ................................................................................................... 1
SPECIFICATIONS.............................................................................................................. 2
PANEL DESCRIPTION ...................................................................................................... 3
CONNECTION DIAGRAM.................................................................................................. 4
OSD MENU........................................................................................................................ 5
OPERATION APPROACH ................................................................................................. 6
LIMITED WARRANTY...................................................................................................... 10

1
INTRODUCTION
The CV-009S Component/CVBS to VGA Scaler Converter provides a cost effective way to convert
Component or CVBS signal to analog PC video (VGA). With this module, VGA based receivers such as
LCD monitors or plasma TV can be readily connected to Component/CVBS sources.
FEATURES
IR remote control
Remote control via Mini-USB
OSD control interface
Maximum pixel rate : 165MHz
525i, 625i, 525P, 625P, 720P, 1080i and many other HDTV formats are supported
Deinterlacer supported
Supports nosie reduction and video enhancement features
Over / Under scanning adjustable
Video H/V mirror supported
Active video area adjustment supported
USB firmware upgradable for expanding compatibility
Wall-mount housing design for easy installation
PACKAGE CONTENTS
1x CV-009S
1x IR Remote control
1x 5V/2A power supply unit
1x User Manual
1x Installation software CD

2
SPECIFICATIONS
Model Name
CV-009S
Technical
Role of usage
Component to VGA Converter
Input Frequency
bandwidth
74.25MHz
Output Frequency
bandwidth
165MHz
Audio support
N/A
ESD protection
[1] Human body model —±19kV [air-gap discharge] & ±12kV[contact
discharge]
[2] Core chipset —±2kV
PCB stack-up
4-layer board [impedance control —differential 100; single 50]
Firmware update
Feasible via USB Port
CEC Channel
N/A
Input
1x 3RCA(YPbPr)
Output
1x VGA
Component connector
RCA x 3[75female]
VGA connector
HD-15 [15-pin D-sub female]
USB connector
Mini B
Mechanical
CV-009S
Housing
Metal enclosure
Dimensions
[L x D x H]
Model
92 x 83 x 30mm [3.6” x 3.3” x 1.2”]
Package
175 x 128 x 134mm [6.9” x 5” x 5.3”]
Carton
662 x 366 x 290mm [2’2” x 1’2” x 1’]
Weight
Model
270g [9.5oz]
Package
520g [18.3oz]
Fixedness
Wall-mounting case with screws
Power supply
5V 2A DC
Power consumption
5 Watts [max]
Operation
temperature
0~40C [32~104F]
Storage temperature
-20~60C [-4~140F]
Relative humidity
20~90% RH [no condensation]

3
PANEL DESCRIPTION
Front Panel
1. VGA OUT: Connect to a VGA display with a VGA male-male cable here.
2. DIP SWITCH: For firmware update
ON []: firmware update mode
OFF []: normal mode
3. LED INDICATOR:
[green]: signal indicator LED
[red]: power indicator LED.
4. IR SENSOR: IR sensor for receiving the IR commands from IR remote
5. PUSH BUTTON
[LEFT]: Down Button
[MID]: Up Botton
[RIGHT]: Menu/Enter Button
Rear Panel
6. +5V DC: Interlocking power jack for 5V DC power supply unit
7. Mini USB: F/W update & control port
8. COMPONENT –Y INPUT
9. COMPONENT –Pb INPUT / CVBS INPUT

4
10. COMPONENT –Pr INPUT
CONNECTION DIAGRAM

5
OSD MENU
1.Output Setup
Out Res.
Output Mode
RGB, YCbCr422
Default Pattern
Disable, White, Cross,
Hatch, Color, Gray,
Windows, H-Ramp,
W-HRamp, W-VRamp,
Diagonal
2.Image
Contrast
0~255 of Contrast Level
Brightness
0~255 of Brightness Level
Saturation
0~255 of Saturation Level
Hue
0~255 of Hue Level
B/W Extension
Off, On
Color Tone
Off, Skin, Green
Edge Enhance
Typ, Mid, Max, Off
Sharpness
0~127 of Sharpness Level
3.Adjustment
Under/Over Scan
-50%~50% of Scan Level
Aspect Ratio
16:9, 4:3
H-Mirror
Off, On
V-Mirror
Off, On
H-Shift
-100~100 of H-Shift Level
V-Shift
-50~50 of V-Shift Level
4. System
Input Res. Info
Firmware Version
Factory Reset

6
OPERATION APPROACH
Method A: Push-in Button
Method B: IR Remote Control
Button
Function
FREEZE
Freeze video
ASPECT RATIO
Aspect ratio change
BLANK
Blank video
EXIT
Exit OSD
ENTER
Enter key
UP
Up key
LEFT
Left key
RIGHT
Right key
DOWN
Down key
MENU
Menu on
INPUT INFO
Source resolution information
1080p60
Select 1080p60 output resolution
1080i60
Select 1080i60 output resolution
720p60
Select 720p60 output resolution
480p60
Select 480p60 output resolution
Down
Up
Menu/Enter

7
Method C: IR Remote Control through Mini-USB port
1
COM Port Selection
2
COM Port Detection Button
3
Output Setup Button
4
Image Button
5
Adjustment Button
6
System Button
7
Input / Output Resolution Info
8
Refresh Input / Output Resolution Info Button
9
Output Quick Selection Button
1. COM Port Selection
Please select the application COM PORT
2. COM Port Detection Button
Click this button to detect the COM PORT
8
9
7
6
5
4
3
1
2

8
3. Output Setup Button
4. Image Button
5. Adjustment Button