SIIG ID-US0411-S1 User manual

1
Introduction
The Industrial USB 2.0 Hub with 15KV ESD Protection
easily adds multiple industrial standard USB 2.0 ports to
your system.
Features and Benefits
• Supports high-speed (480Mb/s), full-speed (12Mb/
s), and low-speed (1.5Mb/s) data transfer modes
• Supports High-speed and Full-speed Packet
Protocol Sequencer for Endpoint 0/1
• Supports redundant 9 to 24 VDC power inputs
• Built in 15KVDC ESD USB interface protection
• Power input surge protection (600W) for each port
• Independent over-current protection
• External power supply (9V to 24V DC) to supply
enough power for power hungry devices
• Metal housing with DIN-Rail and wall mounting
built-in
System Requirements
•Desktop or notebook with an available USB port
• Windows® 8 (32-/64-bit) / 7 (32-/64-bit) / Vista (32-
/64-bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-
/64-bit) / Server 2008 R2 / 2000
04-0865A
Industrial USB 2.0 Hub
with 15KV ESD Protection
Quick Installation Guide

2
PackageContents
• Industrial USB 2.0 Hub with 15KV ESD Protection
• USB Type A to B cable
• DIN-Rail & wall mount kit
• Terminal block
• Quick installation guide
Layout
Industrial 4-Port USB Hub
Figure 1: Industrial 4-Port USB Hub Layout
Figure 2: Industrial 7-Port USB Hub Layout
Industrial 7-Port USB Hub
• Power LED: Green light when power is on; off when
power is off.
Downstream ports
(USB Type A)
Downstream ports
(USB Type A)
Power LED Upstream port
(USB Type B)
3 pin terminal
block
Upstream port
(USB Type B)
Power LED
3 pin terminal
block
DC power
jack
DC power
jack

3
Powering the Hub
Use an external power adapter (not included), with
selectable 9V to 24V DC output, and connect it to the
hub's DC Power Jack or 3-Pin Terminal Block.
Note: The hub requires an external power adapter
(not included) to work properly.
DC Power Jack
Plug the power adapter into a reliable power source then
connect it to the hub's DC Power Jack. See Figure 3.
Figure 3: DC In
3-Pin Terminal Block
Plug the included terminal block into the hub's terminal
block connector. See Figure 4.
Refer to the Pin Assignment on page 4 for wiring the
power adapter.
Figure 4: Power Terminal
DC power
jack

4
Pin Assignment
3-Pin Terminal Block
USB Type B Upstream Port
132
12
34
Figure 5
Figure 6

5
Hardware Installation
Mount your hub on the wall or DIN-Rail, if needed.
DIN-Rail Mounting
1. Use the included screws to install the DIN-Rail kit to
the hub.
DIN-Rail kit
2. Insert the top of the DIN-Rail clip onto the DIN-Rail
track, then gently push the bottom of the hub to
secure it to the DIN-Rail track. See Figure 8.
Figure 7
Figure 8

6
Wall Mount Plate Mounting
Use the provided Wall Mount Plate to mount the hub to
the wall. See Figure 9.
Figure 9
Wall Mount
Plate
Wall Mount
Plate
Wall
Wall

7
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support has answers! Simply visit ourwebsite
at www.siig.com and click Support. Our online support database is updated
daily with new drivers and solutions. Answers to your questions could be
just a few clicks away. You can also submit questions online and a technical
support analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty
covers the original purchaser and guarantees the product to be free of any
defects in materials or workmanship for three (3) years from the date of
purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or
product having similar features and functionality) the product if defective in
materials or workmanship. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. Please see our
web site for more warranty details.
Ifyou encounter any problemswiththis product, please followtheprocedures
below.
A) If it is within the store's return policy period, please return the product to
the store where you purchased it.
B) If your purchase has passed the store's return policy period, please follow
these steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support,
then Request A Product Replacement to submit a request to SIIG RMA
or fax a request to 510-657-5962. Your RMA request will be processed, if
the product is determined to be defective, an RMA numberwill be issued.
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s) and any
otheraccessories that came withtheoriginalpackage must be included.
•Clearly write your RMA number on the top of the returned package.
SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted
on the outside of the shipping carton.
•You are responsible for the cost of shipping to SIIG. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground in the U.S.
and International Economy outside of the U.S. at no cost to the
customer.

PRODUCT NAME
Industrial USB 2.0 Hub with 15KV ESD Protection
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
Industrial USB 2.0 Hub with 15KV ESD Protection is a trademark of SIIG, Inc. SIIG and the SIIG logo
areregisteredtrademarksofSIIG,Inc. MicrosoftandWindowsareregisteredtrademarksofMicrosoft
Corporation. Allothernamesusedinthispublicationarefor identification only andmaybetrademarks
oftheirrespectiveowners.
March, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. Allcentered around thedistribution andswitching ofA/V signals
overCAT5/6,theseproductsinclude matrix switches, distribution amplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providing high quality products while keeping economical and competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.