Silvercrest SSH 600 A1 User manual

STECKDOSEN-HEIZLÜFTER
Bedienungsanleitung
Dieses Produkt ist nur für gut isolierte
Räume oder für den gelegentlichen
Gebrauch geeignet.
IAN 346692_2001
PLUG-IN FAN HEATER SSH 600 A1
PLUG-IN FAN HEATER
Operating instructions
This product is only suitable for well
insulated spaces or occasional use.

GB/IE/NI Operating instructions Page 1
DE/AT/CH Bedienungsanleitung Seite 25
Before reading, unfold the page containing the illustrations and familiarise
yourself with all functions of the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen
Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

SSH 600 A1 GB│IE│NI │ 1■
Contents
Introduction ...................................3
Information about these operating instructions .................3
Limitation of liability......................................3
Proper use .............................................4
Warnings and symbols used ...............................4
Safety........................................6
Package contents and transport inspection..........9
Operating components ..........................9
Operation ....................................10
Requirements for the operating location .....................10
Handling and operation ........................11
Switching the appliance on and off.........................11
Setting the temperature ..................................12
Setting the heating/blower level ...........................13
Set heating time........................................13
Protective devices..............................14
Overheating protection ..................................14
Tilt cut-out.............................................14
Cleaning .....................................15
Storage......................................15
Disposal......................................16
Disposal of the appliance ................................16
Disposal of the packaging................................16

SSH 600 A1
■ 2 │ GB│IE│NI
Troubleshooting ...............................17
Fault causes and remedies................................17
Appendix ....................................18
Technical specifications ..................................18
Notes on the EU Declaration of Conformity ..................18
Information requirements for electric local space heaters ........19
Kompernass Handels GmbH warranty ......................21
Service...............................................23
Importer ..............................................23

SSH 600 A1 GB│IE│NI │ 3■
Introduction
Information about these operating instructions
Congratulations on the purchase of your new appliance.
You have selected a high-quality product. The operating instructions
are part of this product. They contain important information about
safety, usage and disposal. Before using the product, please familiar-
ise yourself with all operating and safety instructions. Use the product
only as described and for the range of applications specified. Please
also pass these operating instructions on to any future owner.
Limitation of liability
All the technical information, data and instructions regarding
installation, connection and operation contained in these operating
instructions correspond to the latest information available to us at the
time of printing and takes our previous experience and know-how
into account.
No claims may be derived from the specifications, figures and de-
scriptions in these operating instructions. The manufacturer assumes
no responsibility for damage caused by failure to observe these
instructions, improper use, incompetent repairs, making unauthorised
modifications or for using unapproved replacement parts.

SSH 600 A1
■ 4 │ GB│IE│NI
Proper use
This plug-in fan heater, hereinafter referred to as the appliance or
heater, is intended only for heating closed interior rooms and is for
private use only.
This appliance is not intended for use in areas where special conditions
may apply, such as corrosive or potentially explosive atmospheres
(dust, vapour or gas). It is not intended for heating up cars or tents,
for example.
The appliance must not be used outside of closed rooms. Any other
usage or modification of the appliance is deemed to be improper
and carries a significant risk of accidents. It is not intended for use
in commercial or industrial applications.
The manufacturer accepts no liability for damage resulting from
improper use, improper application or non-observance of these
operating instructions.
Warnings and symbols used
The following warnings are used in these operating instructions
(if applicable):
DANGER
A warning notice at this hazard level indicates an
imminently hazardous situation.
If the hazardous situation is not avoided, it could result in death or
serious physical injury.
► Follow the instructions in this warning to prevent a fatality or
serious personal injury.

SSH 600 A1 GB│IE│NI │ 5■
WARNING
A warning notice at this hazard level indicates a
potentially hazardous situation.
Failure to avoid this hazardous situation could result in injuries.
► Follow the instructions in this warning notice to prevent injuries.
CAUTION
A warning at this hazard level indicates a risk of
property damage.
Failure to avoid this situation could result in property damage.
► Follow the instructions in this warning notice to prevent property
damage.
NOTE
► A note provides additional information that makes handling the
appliance easier for you.
Do not cover the appliance!
Covering the appliance can lead to overheating
and result in a fire!
Attention! Hot surface!
This symbol warns of hot surfaces on the appliance.
There is a risk of burns!

SSH 600 A1
■ 6 │ GB│IE│NI
Safety
This section contains important safety instructions for using the ap-
pliance. Failure to follow the warnings and instructions listed below
may result in electric shock, fire and/or serious injury. Please read
these operating instructions completely before use.
■ Check the appliance for visible external dam-
age before use. Do not use an appliance that
has been damaged or dropped.
■ This appliance may be used by children
aged 8 years and above and by persons
with reduced physical, sensory or mental
capabilities or lack of experience and/or
knowledge if they are being supervised or
have been instructed with regard to the safe
use of the appliance and have understood
the potential risks. Do not allow children to
play with the appliance.
■ Cleaning and user maintenance must not be
performed by children unless they are older
than 8 years of age and are supervised.
■ Children younger than 3 years old should be
kept away from the appliance unless they are
constantly monitored.

SSH 600 A1 GB│IE│NI │ 7■
■ Children older than 3 and younger than
8 years of age may only switch the appliance
on and off if they are supervised or instructed
in the safe use of the appliance and have
understood the resulting dangers, and pro-
vided that the appliance is located or in-
stalled in its normal operating position.
■ Children older than 3 and younger than
8 years of age may not plug in, regulate or
clean the appliance and may not carry out
user maintenance tasks.
■ Children must be supervised to make sure that
they do not play with the appliance.
■ Do not operate the appliance with an exten-
sion cable, adapter or on a multiple socket.
■ The appliance may only be used on a single
socket.
■ Make sure that the mains socket being used
is always easily accessible so that the appli-
ance can be quickly disconnected from the
power supply in an emergency.

SSH 600 A1
■ 8 │ GB│IE│NI
■ Do not use the appliance together with a
programmable switch, a timer, a separate
remote control system or any other system
which switches the heater on automatically,
as this could lead to a fire risk if the heater is
covered or set up incorrectly. Do not operate
the appliance unattended.
■ The appliance must not be used in the im-
mediate vicinity of a bath, shower or swim-
ming pool. Do not use the appliance in
bathrooms, washrooms or similar areas.
■ The appliance is to be installed so that a per-
son in the bath or shower is unable to touch
the switch and other controls.
■WARNING! Some parts of the product
may be very hot and cause burns. Be particu-
larly careful when children and vulnerable
people are present.
■ Do not install the heater near curtains or other
flammable materials as there is a risk of fire.
■ The heater must not be located immediately
below a socket outlet.

SSH 600 A1 GB│IE│NI │ 9■
Package contents and transport
inspection
The appliance is supplied with the following components as standard:
ƔPlug-in fan heater
ƔThese operating instructions
NOTE
► Check the package for completeness and signs of visible
damage.
► If the delivery is incomplete or damage has occurred as a result
of defective packaging or during transport, contact the service
hotline (see section Service).
♦ Remove all packaging materials and any protective film from the
appliance.
NOTE
► You may notice a slight smell when using the appliance for the
first time. This is normal and is completely harmless.
Operating components
button
Operating LED
Display
button
button
SET button
Mains plug
Recessed grips

SSH 600 A1
■ 10 │ GB│IE│NI
Operation
Requirements for the operating location
For safe and trouble-free operation of the appliance, the operating
location must fulfil the following requirements:
–The appliance may only be operated in an upright position and
fully assembled.
–The mains socket must be easily accessible so that the appliance
can be quickly disconnected in an emergency.
–Maintain a minimum clearance of 20 cm at the sides,
30 cm above and 50 cm in front.
–Ensure that the air can always enter and escape freely.
Otherwise, there could be a heat build-up in the appliance.
DANGER
Risk of fire due to contact with fabrics!
► Do not allow flammable materials (e.g. textiles) to come into
contact with the appliance.
► Do not cover the appliance.

SSH 600 A1 GB│IE│NI │ 11 ■
Handling and operation
Switching the appliance on and off
♦ Plug the appliance into a suitable, easily accessible mains socket.
The operating LED 2lights up red to show that the appliance is
in standby mode.
♦ Press the button1to turn on the fan heater. The factory
preset temperature  (25° Celsius) appears on the display3.
♦ Press the button1again to switch the fan heater back into
standby mode. The display3goes out, while the operating
LED2remains lit up red. The fan runs on a while to cool the
appliance down.
♦ To switch off the appliance completely, disconnect it from the
mains power supply. To do this, remove it from the mains socket.
WARNING
► The fan heater gets very hot during use. Allow it to cool down
before you disconnect it from the mains socket. Touch the heater
only by the recessed grips8provided.

SSH 600 A1
■ 12 │ GB│IE│NI
Setting the temperature
You can set a temperature range from 15° Celsius to 30° Celsius on
the fan heater.
♦ Press the button1to turn on the fan heater. The factory
preset temperature () or the last-used temperature appears
on the display3.
♦ Press the button4button repeatedly to increase the tempera-
ture in steps of 1° Celsius.
♦ Press the button5button repeatedly to reduce the tempera-
ture in steps of 1° Celsius.
NOTE
► The fan heater only starts heating when the room temperature
falls below the set temperature value.
► As soon as the room temperature has reached the set temperature
value, the appliance stops heating until the room temperature
drops below the set temperature value again.

SSH 600 A1 GB│IE│NI │ 13 ■
Setting the heating/blower level
The fan heater has two combined heating/blowing levels.
♦ With the appliance switched on, press the SETbutton6once.
++ (high heating/blower level) appears on the display3.
♦ Press the button4or the button5to switch between the
high heating/blowing level (++) and the low heating/blowing
level (//).
Set heating time
The appliance has a timer that you can use to set the desired heating
time between 1 to 24 hours. Once this heating period is over, the
appliance automatically switches to standby mode.
♦ With the appliance switched on, press the SETbutton6twice.

(Continuous operation) flashes on the display3.
♦ Press the button4button repeatedly to increase the heating
duration in steps of 1 hour.
♦ Press the button5button repeatedly to reduce the heating
duration in steps of 1 hour.
NOTE
► After approx. 5 seconds without a button being pressed, the set
heating duration is accepted and the timer is activated.
► When the timer is activated, the display3switches every few
seconds between the set temperature and the heating duration
display.

SSH 600 A1
■ 14 │ GB│IE│NI
Protective devices
Overheating protection
The appliance is fitted with a thermostatically controlled overheating
protector. If the appliance becomes too hot internally, the heating
element and fan switch off automatically. In this case, pull the ap-
pliance out of the mains socket and let it cool down for 30 minutes.
Then plug the appliance back into the mains socket and switch it on
again.
WARNING
Overheating can lead to a risk of fire!
► Check that the appliance can sufficiently dissipate the heat
generated: Is the appliance covered, are the ventilation slots
blocked or is the fan blocked?
► If possible, eliminate the problem or contact the Service Hotline
(see the section Service).
Tilt cut-out
The fan heater must always be plugged into a mains socket in an
upright position, with the display3at the top. The tilt cut-out switch-
es the appliance off as soon as it is tilted by a few degrees from
the upright position. As soon as the appliance is back in an upright
position, it can be switched back on again.

SSH 600 A1 GB│IE│NI │ 15 ■
Cleaning
WARNING
► Before cleaning the appliance, disconnect the appliance from
the mains power socket!
► Allow the appliance to cool down before cleaning to prevent
any risk of burns.
► Clean the appliance only when it is cool.
CAUTION
► To avoid irreparable damage to the appliance, ensure that no
moisture can get into it during cleaning.
► Never immerse the appliance in water and protect it from
splashing or sprayed water.
♦ Clean the housing only with a soft damp cloth and a mild
detergent.
♦ Remove accumulations of dust on the protective grille and the
ventilation slots with a paintbrush or vacuum cleaner.
Storage
♦ If you are not using the appliance, disconnect it from the mains
power supply and store it in a clean, dry place away from direct
sunlight.

SSH 600 A1
■ 16 │ GB│IE│NI
Disposal
Disposal of the appliance
The symbol showing a crossed-out dustbin means that this
appliance is subject to Directive 2012/19/EU. This
directive states that this appliance may not be disposed of
in the normal household waste at the end of its useful life,
but must be handed over to specially set-up collection
locations, recycling depots or disposal companies.
This disposal is free of charge for the user. Protect the
environment and dispose of this appliance properly.
Your local community or municipal authorities can provide
information on how to dispose of the product.
Disposal of the packaging
The packaging materials have been selected for their
environmental friendliness and ease of disposal and are
therefore recyclable. Dispose of packaging materials that
are no longer needed in accordance with applicable
local regulations.
Dispose of the packaging in an environmentally friendly
manner.
Note the labelling on the packaging and separate the
packaging material components for disposal if necessary.
The packaging material is labelled with abbreviations (a)
and numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard,
80–98: composites.

SSH 600 A1 GB│IE│NI │ 17 ■
Troubleshooting
This section contains important information on fault identification and
rectification.
WARNING
► Repairs to electrical appliances should only be carried out by
specialists trained by the manufacturer. Improper repairs can
cause considerable risks to users and damage to the appliance.
Fault causes and remedies
The following table will help you to identify and rectify minor
malfunctions:
Fault Possible cause Remedy
The appliance
will not switch
on.
The plug is not con-
nected.
Insert the plug com-
pletely into the mains
power socket.
The mains socket is not
supplying any power.
Check the house mains
fuse.
The tilt cut-out has
been activated.
Plug the appliance up-
right into the mains sock-
et with the display3at
the top.
The appliance
switches itself to
standby mode.
The set heating time
has expired.
Increase the heating
time if you wish.
The error code
(( appears on
the display 3.
There is a fault with the
temperature sensor.
Contact our customer
service department.
NOTE
► If the above-mentioned solutions do not resolve the problem,
please contact Customer Service (see section Service).