silverlynx Hugo Bed User manual

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
Hugo Bed [with Extensions]
Assembly Instructions
Please retain these instructions for future reference
Please read through your assembly instructions carefully to ensure that you can assemble your
new purchase without stress.
Hugo Bed [with Extensions]
NOTE –it is recommended that two people assemble this bed
WE ADVISE YOU DO NOT USE POWERED DRILLS TO ASSEMBLE ANY BOLTS ON THIS BED
To assemble your bed you have been supplied with
Other equipment required - wrench (not provided)
Thank you for purchasing a Silverlynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established
partnerships with Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer
satisfaction.
Silverlynx is a value’s based business. Our commitment to quality, evolving design leadership,
customer service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your Silverlynx bed.
Hardware Pack containing - 12x (M4) 10mm button head bolts; 2x 38mm screws; 1x allen
key; 4x 50mm bolts; 2x 90mm bolts with nuts; 8x washers
Bed Frame Parts
Slat System
See the attached document “Amendment to instructions for all Silverlynx beds”.

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 1 –Begin with your Bed Head and base (Extensions will be fitted last). Position Bed Head
and Side Rails approximately where your bed is to be set up, making sure that you can access
behind the Bed Head (required for Step 7). Note, the two button head bolts that are pre-fitted to
your Side Rails must be positioned closer to the foot end of the bed. Connect the Side Rails to the
Bed Head by hooking the Side Rail brackets onto the Head brackets.
STEP 2 –Screw three button head bolts (M4) into the position shown below to connect the Side
Rails to the Bed Head and tighten (finger tight only).
STEP 3 –Complete the above process on the other Side Rail, then repeat with the Foot Panel.
STEP 4 –Remove the two button head bolts for the Floating Bar from the foot end of each Side
Rail. Gently lift the Side Rails and position the Floating Bar, lining up the holes on each end of the
Floating Bar with the holes on the Side Rails.
STEP 5 –Using the bolts you removed from the Side Rails, secure (finger tight only) the Floating
Bar in place
Step 6 –Ensure that the bed is sitting square and then tighten all button head bolts using the
allen key. Once snug, tighten only with ¼ turn of the Allen Key. DO NOT USE powered drills as
over-tightening can cause foot end rail to bow. Your bed should now look like the diagram on the
next page.
STEP 3
STEP 4-5

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 7 –Carefully move your Extensions into place beside the Bed Head. Use the (2x) 90mm
bolts, (2x) nuts, & (4x) washers provided to connect through the corner brackets at the back of
the Bed Head (under the top rail). Ensure you use a washer on each side of the corner blocks as
shown below. Do not tighten until you have connected the legs to the Extensions in the next step.
STEP 8 –Use the (4x) 50mm bolts with the (4x) remaining washers (placed between the leg and
the bolt head) to secure the Extensions to the Bed Head Leg. Tighten the bolts on the Corner
Blocks using the allen key (provided) and wrench (not provided), then tighten the Bed Head Legs
using the allen key. Be careful not to overtighten –once snug tighten only with ¼ turn of the allen
key. Once the Extensions are fitted, you may unscrew the transport leg from the front of your
floating shelves.
STEP 6
STEP 7
STEP 7-8
STEP 7 - BOLT THROUGH CORNER BLOCK
BLOCKS
STEP 8
BOLT THROUGH BED HEAD LEG

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 9 –To set up the slat and spine system, proceed to the instructions titled “Amendment to
instructions for all Silverlynx beds”. Note the 2x 38mm screws provided in the hardware pack can
be used in this section of the assembly.
NOTES
•Button head bolts should be regularly inspected and may need to be retightened periodically
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your Silver Lynx product is crafted with care, properly maintained, it will mature over time
developing a rich deep patina enhancing its appearance. To get the best performance from your
Silver Lynx product, please follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended
periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the suite.
•Do not use cordless drivers or power drills to tighten your bed brackets, as over-tightening can
cause the foot end rail to bow.
Contact your retailer or our sales office for further information