silverlynx FLOATING BASE BED User manual

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
FLOATING BASE BED
Assembly Instructions
Please retain these instructions for future reference
Please read through these assembly instructions carefully to ensure that you can assemble your new purchase
without stress. These detailed instructions will guide you on how to prepare and assemble your bedroom suite.
DIFFICULTY
WE ADVISE YOU DO NOT USE POWERED DRILLS TO ASSEMBLE ANY BOLTS ON THIS BED
EQUIPMENT PROVIDED
Thank you for purchasing a SilverLynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established partnerships with
Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer satisfaction.
SilverLynx is a values-based business. Our commitment to quality, evolving design leadership, customer
service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your SilverLynx bed.
Hardware Pack: containing - 12x (M4) 10mm button head bolts; 2x 38mm screws; 1x allen key
*NOTE: The hardware pack may contain more items than required. Please contact our sales team if you have any
questions/concerns.
Slat System: See the attached document “Amendment to instructions for all SilverLynx beds”.
Bed Frame Parts:

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 1 –Position Bed Head and
Siderails approximately where your bed
is to be set up, making sure the two
button head bolts that are pre-fitted to
your Siderails are closest to the foot end
of the bed (this is where the Floating Bar
will go). Connect the Siderails to the
Bed Head by hooking the Siderail
brackets onto the Head brackets.
STEP 2 –Screw three button head
bolts (M4) into the position shown to
connect the Siderails to the Bed Head
and tighten (finger tight only).
Having trouble? See *Helpful Tips* at
the end of this document.
STEP 3 –Complete the above
process on the other Siderail, then
repeat with the Foot Panel.
Having trouble? See *Helpful Tips* at
the end of this document.
STEP 4 –Remove the two button
head bolts for the Floating Bar from the
foot end of each side rail. Gently lift the
Siderails and position the Floating Bar,
lining up the holes on each end of the
Floating Bar with the holes on the
Siderails.
STEP 5 –Using the bolts you
removed from the Siderails, secure
(finger tight) the Floating Bar in place.
STEP 6 –Ensure that the bed is
sitting square and then tighten all
button head bolts using the allen key.
Once snug, tighten only with ¼ turn of
the Allen Key. DO NOT USE powered
drills as over-tightening can cause foot
end rail to bow. Your bed should now
look like the following diagram.
STEP 7 –To set up the slat and spine
system, proceed to the instructions
titles “Amendment to instructions for all
SilverLynx beds”. Note the 2x 38mm
screws provided in the hardware pack
can be used in this section of the
assembly.
STEP 1 & 2
STEP 3
STEP 4 & 5
STEP 6

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
NOTES
•Button head bolts should be regularly inspected and may need to be retightened periodically
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your SilverLynx product is crafted with care, properly maintained, it will mature over time developing a rich
deep patina enhancing its appearance. To get the best performance from your SilverLynx product, please
follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the suite.
•Do not use cordless drivers or power drills to tighten your bed brackets, as over-tightening can cause the
foot end rail to bow.
Contact your retailer or our sales office for further information
*Helpful Tips*
STEP 2 & 3
The button head bolts that connect the Siderails to the Bed Head & Foot can sometimes be tricky to align. If you
are having trouble, try supporting the bottom edge of the Siderail near the bracket and lift it up while you
connect the bolts. This can help line up the holes in both brackets so that the bolt can connect easily.
GENERAL
Make sure not to tighten bolts before attaching all components and making sure they sit square. Once you are
ready, make sure all bolts are snug, then tighten only with ¼ turn of the Allen Key. DO NOT USE powered drills
as over-tightening can cause components to bow.
Never force bolts if you can feel resistance as this can cause the thread to strip. Try to adjust the hole alignment
until your bolt can connect easily by hand.