silverlynx MAITLAND User manual

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:sale[email protected] W:www.silverlynx.com.au
MAITLAND (Short Suite)
Assembly Instructions
Please retain these instructions for future reference
Please read through these assembly instructions carefully to ensure that you can assemble your new purchase
without stress. These detailed instructions will guide you on how to prepare and assemble your bedroom suite.
DIFFICULTY
WE ADVISE YOU DO NOT USE POWERED DRILLS FOR THIS ASSEMBLY
EQUIPMENT PROVIDED
Thank you for purchasing a SilverLynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established partnerships with
Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer satisfaction.
SilverLynx is a values-based business. Our commitment to quality, evolving design leadership, customer
service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your SilverLynx product.
Hardware Pack: containing –6x 1 ¾ inch screws
Parts:

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:sale[email protected] W:www.silverlynx.com.au
STEP 1 –Place the Bedsides on either
side of the mattress and base set (not
pictured), approximately where your bed
is to be set up. Ensure there is enough
space behind the Bedsides to use a
screwdriver (next steps).
STEP 2 –Lower the Bedhead panel
onto the Bedsides, making sure the
clearance holes in the Bedhead panel
line up with the pilot holes in the back
of the Bedsides. DO NOT slide
Bedhead on Bedside tops. Make sure
to LIFT Bedhead to avoid scratching
the top of your Bedsides.
STEP 3 –Install each of the six
screws provided through the clearance
holes on the Bedhead panel and screw
them into the pilot holes on the
Bedsides using a phillips head
screwdriver. Ensure the screws are
driven in straight to avoid screws
damaging the surface of the Bedsides.
Note: we advise you DO NOT use
powered drills for this assembly.
STEP 4 –Once assembled, move
Bedhead and Bedsides toward wall,
ensuring they are moved evenly
without and twist, as this may cause
the joint to fail. Your bed should now
look like the following diagram.
STEP 1 & 2
STEP 3
STEP 4

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:sale[email protected] W:www.silverlynx.com.au
NOTES
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your SilverLynx product is crafted with care, properly maintained, it will mature over time developing a rich
deep patina enhancing its appearance. To get the best performance from your SilverLynx product, please
follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the product.
•Do not use cordless drivers or power drills to tighten any bolts, as over-tightening can cause components to
bow, and can cause damage to the bolts.
Contact your retailer or our sales office for further information