silverlynx LINCOLN 4 User manual

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
LINCOLN 4 POSTER BED
Assembly Instructions
Please retain these instructions for future reference
Please read through these assembly instructions carefully to ensure that you can assemble your new purchase
without stress. These detailed instructions will guide you on how to prepare and assemble your bedroom suite.
DIFFICULTY
WE ADVISE YOU DO NOT USE POWERED DRILLS TO ASSEMBLE ANY BOLTS ON THIS BED
Thank you for purchasing a SilverLynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established partnerships with
Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer satisfaction.
SilverLynx is a values-based business. Our commitment to quality, evolving design leadership, customer
service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your SilverLynx product.
Please note, your bed head may look different to this image, however the following instructions will still apply

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
EQUIPMENT PROVIDED
Hardware Pack: containing - 12x (M6) 10mm button head bolts; 2x 38mm screws; 4x M6 110mm bolts;
2x allen keys
Slat System: See the attached document “Amendment to instructions for all SilverLynx beds”.
Bed Frame Parts:
Not Provided: Phillips head screwdriver

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
NOTE –The Lincoln 4 Poster has been
shipped as shown on the previous page,
however, the Bed Head and Foot can be
partially knocked-down to assist delivery
through tight spaces if needed. If you
are going to partially knock-down your
bed before setup, please start at
STEP 1. If your bed can be delivered
without knocking-down, please proceed
to STEP 3.
STEP 1 –(A) If you have purchased
the Full Height Upholstered Bedhead,
first remove the fixing panel and the top
two upholstered panels from the back
of the Bedhead by removing the screws
as necessary. NOTE - we recommend
that you DO NOT remove the bottom
upholstered panel.
(B) Next (or first for all other styles),
remove the top capping from the
Bedhead and Foot by loosening the
bolts as shown below using the small
allen key provided.
STEP 2 –Move your components into
the space where they are to be set up.
Re-fit the top capping on the head and
foot. Bolts should be wound in firmly
but not overtight. Re-fit the two
upholstered panels and the fixing
panel.
STEP 3 –Place your Bedhead and
Side Rails approximately where you
would like your bed to be set up.
Connect the Side Rail to the Bedhead
by hooking the side rail brackets onto
the head brackets.
STEP 4 –Screw three button head
bolts (M6) into the position shown to
connect the Side Rails to the Bed Head
and tighten (finger tight only).
Having trouble? See *Helpful Tips* at
the end of this document.
STEP 1(A)
STEP 4
STEP 1(B)

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 5 –Complete the above
process on the other Side Rail, then
repeat with the Foot Panel.
Having trouble? See *Helpful Tips* at
the end of this document.
STEP 6 –Ensure that the bed is
sitting square and then tighten all
button head bolts using the allen key.
Once snug, tighten only with ¼ turn of
the Allen Key. DO NOT USE powered
drills as over-tightening can cause foot
end rail to bow.
STEP 7 –Fit your Top Connecting
Rails using the 4x 110mm bolts and the
small allen key provided. Bolts should
be wound in firmly but not overtight.
After this step your bed should look like
the diagram on the next page.
STEP 5
STEP 7

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 8 –To set up the slat and spine
system, proceed to the instructions
titles “Amendment to instructions for all
SilverLynx beds”. Note the 2x 38mm
screws provided in the hardware pack
can be used in this section of the
assembly.
NOTES
•Button head bolts should be regularly inspected and may need to be retightened periodically
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your SilverLynx product is crafted with care, properly maintained, it will mature over time developing a rich
deep patina enhancing its appearance. To get the best performance from your SilverLynx product, please
follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the product.
•Do not use cordless drivers or power drills to tighten any bolts, as over-tightening can cause components to
bow, and can cause damage to the bolts.
Contact your retailer or our sales office for further information
*Helpful Tips*
STEP 2 & 3
The button head bolts that connect the Siderails to the Bed Head & Foot can sometimes be tricky to align. If you
are having trouble, try supporting the bottom edge of the Siderail near the bracket and lift it up while you
connect the bolts. This can help line up the holes in both brackets so that the bolt can connect easily.
GENERAL
Make sure not to tighten bolts before attaching all components and making sure they sit square. Once you are
ready, make sure all bolts are snug, then tighten only with ¼ turn of the Allen Key. DO NOT USE powered drills
as over-tightening can cause components to bow.
Never force bolts if you can feel resistance as this can cause the thread to strip. Try to adjust the hole alignment
until your bolt can connect easily by hand.