silverlynx Montauk Bed User manual

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
Montauk Bed
Assembly Instructions
Please retain these instructions for future reference
Please read through your assembly instructions carefully to ensure that you can assemble your
new purchase without stress. You have been provided with detailed instructions on how to
prepare and assemble your bedroom suite.
Montauk
NOTE –it is recommended that two people assemble this bed
WE ADVISE YOU DO NOT USE POWERED DRILLS TO ASSEMBLE ANY PART OF THIS BED
To assemble your bed you have been supplied with
Thank you for purchasing a Silverlynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established
partnerships with Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer
satisfaction.
Silverlynx is a value’s based business. Our commitment to quality, evolving design leadership,
customer service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your Silverlynx bed.
Hardware Pack containing
12x (M4) 10mm button head bolts; 2x 32mm screws; 1x allen key
Bed Frame Parts
Slat System
See the attached document “Amendment to instructions for all Silverlynx beds”.

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 1 –Place your bed head and side rails approximately where you would like your bed to be
set up, noting that the brackets pre-fixed to the side rails sit closer to the top edge. Connect the
side rails to the bed head by hooking the side rail brackets onto the head brackets.
STEP 2 –Screw three button head bolts (M4) into the position shown below to connect the side
rails to the bed head and tighten (finger tight only).
STEP 3 –Complete the above process on the other side rail.
STEP 4 –Lift the Foot Panel into place, hooking the side rail brackets over the brackets on the
Foot Panel and secure with the remaining button head bolts (finger tight only)
STEP 5 –Ensure that the bed is sitting square and then tighten all button head bolts using the
allen key. Once snug, tighten only with ¼ turn of the Allen Key. DO NOT USE cordless drivers or
power drills as over-tightening can cause the foot end rail to bow. After this step your bed should
look like the diagram on the next page.
STEP 1-2

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 6 –To set up the slat and spine system, proceed to the instructions titled “Amendment to
instructions for all Silverlynx beds”.
NOTES
•Button head bolts should be regularly inspected and may need to be retightened periodically
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your Silver Lynx product is crafted with care, properly maintained, it will mature over time
developing a rich deep patina enhancing its appearance. To get the best performance from your
Silver Lynx product, please follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended
periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the suite.
•Do not use cordless drivers or power drills to tighten your bed brackets, as over-tightening can
cause the foot end rail to bow.
Contact your retailer or our sales office for further information
STEP 5