silverlynx SILVERLYNX Series User manual

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
AMENDMENT TO INSTRUCTIONS
FOR ALL SILVERLYNX BEDS
Assembly Instructions
Please retain these instructions for future reference
** Use these instructions in place of instructions labelled “spine ULTRA FOUNDATION” **
Please read through these assembly instructions carefully to ensure that you can assemble your new purchase
without stress. These detailed instructions will guide you on how to prepare and assemble your bedroom suite.
DIFFICULTY
WE ADVISE YOU DO NOT USE POWERED DRILLS TO ASSEMBLE ANY BOLTS ON THIS BED
Thank you for purchasing a SilverLynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established partnerships with
Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer satisfaction.
SilverLynx is a values-based business. Our commitment to quality, evolving design leadership, customer
service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your SilverLynx bed.
NOTE: This amendment replaces the instructions that come packaged with the “Spine Ultra Foundation”
system. Design and configuration of our beds varies, therefore please use the appropriate configuration
suitable to your purchase to correctly position support tubes and support legs.

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
Spine Ultra Foundation Slat System –for SilverLynx Beds
(Super King / King / Queen / Double)
Please use these instructions to assemble the spine system for your SilverLynx Bed and retain for future reference
Your Foundation Slat System comes complete with the following parts:
MATCHING/FLOATING FOOT
SUPER KING
12x timber slats (part no.1)
2x spines (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
4x support leg (part no.5)
KING
12x timber slats (part no.1)
1x spine (part no.2)
3x support tubes (part no.3)
3x end tab kits (incl. bolts) (part no.4)
3x support leg (part no.5)
QUEEN
12x timber slats (part no.1)
1x spine (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
1x support leg (part no.5)
DOUBLE
11x timber slats (part no.1)
1x spine (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
1x support leg (part no.5)
DRAWER BASE
SUPER KING
9x timber slats (part no.1)
2x spines (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
4x support leg (part no.5)
KING
9x timber slats (part no.1)
1x spine (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
2x support leg (part no.5)
QUEEN
9x timber slats (part no.1)
1x spine (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
1x support leg (part no.5)
DOUBLE
8x timber slats (part no.1)
1x spine (part no.2)
2x support tubes (part no.3)
2x end tab kits (incl. bolts) (part no.4)
1x support leg (part no).
Part no.1
TIMBER SLATS
Part no.2
SPINE
Part no.3
SUPPORT TUBES
Part no.4
END TAB KITS
Part no.5
SUPPORT
LEGS

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 1 Slide 12 x timber slats through
the spine. After all slats have been fitted,
position the spine in the middle, as per
image below. OR for King Size space
the 2 spines evenly apart - 1/3 of the
width of the slats. Ensure that the slat
with a hole in either end is placed at the
centre of your bed. This is so the centre
slat can be screwed to the side rail.
STEP 2 –You will need to prepare your
leg/s for the next stage. Roughly set up
the support leg height to fit your bed
height as shown. You may need to
remove the square tube labelled ‘bottom
section’, and flip it around so that the
thread for the screw-on foot is at the
bottom. Using the bolt and nut provided
lock the leg into position. The height can
be fine-tuned at the foot once the
system is in place (step 7).
STEP 3 –Slide the support tube(s)
through the spine between slats as per
the recommendation on the first page
of this guide.
STEP 4 –Be sure to slide the support
tube through the support leg at the same
time. Ensure the leg is positioned
between the spine as per diagram.

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 5 –Bolt on an end tab to each
end of the support tube. Be sure the flat
edge sits on top of the slats.
STEP 6 –Position complete
foundation system onto your bed side
rails.
STEP 7 –Fine tune support leg so it
sits approximately about 5 –15 mm off
the floor.
STEP 8 –When finished we
recommend that you use the 2 x 1 ¼”
screws (supplied) and screw the slat
with hole in either end (centre slat) into
the cleats
STEP 5
NOTES
•Button head bolts should be regularly inspected and may need to be retightened periodically
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your SilverLynx product is crafted with care, properly maintained, it will mature over time developing a rich
deep patina enhancing its appearance. To get the best performance from your SilverLynx product, please
follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the suite.
•Do not use cordless drivers or power drills to tighten your bed brackets, as over-tightening can cause the
foot end rail to bow.
Contact your retailer or our sales office for further information