silverlynx Gas Lift Bed User manual

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[email protected]m.au W:www.silverlynx.com.au
Gas Lift Bed
Assembly Instructions
Please retain these instructions for future reference
Please read through your assembly instructions carefully to ensure that you can assemble your
new purchase with little or no stress. You have been provided with detailed instructions on how to
prepare and assemble your bedroom suite.
Gas Lift Bed
NOTE –two people are required to assemble this bed
To assemble your bed you have been supplied with
12x 12mm button head bolts; 4x 15mm phillips head screws; 6x mushroom (phillips) head bolts;
6x nuts; 1x allen key
Thank you for purchasing a Silverlynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established
partnerships with Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer
satisfaction.
Silverlynx is a value’s based business. Our commitment to quality, evolving design leadership,
customer service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your Silverlynx bed.

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[email protected]m.au W:www.silverlynx.com.au
STEP 1 – Attaching the Side Rails to the Bed Head & Foot
Lay out the Bedhead, Foot, and Side Rails roughly in the position your bed is to be set up. Make
sure the Gas Lift Struts (pre-attached to side rails) are set up closer to the head panel as shown
below. Connect the side rails to the bedhead by hooking the side rail bracket onto the bed head
bracket and fix using 3x 65 mm button head bolts (only finger tight). Repeat on the foot end.
STEP 2 –Optional angle brackets located near the bottom of each end of your side rails can be
fixed to keep the side rails parallel with the bedhead and foot. Use the 15mm screws provided to
screw through the angle bracket. Once snug, tighten only with ¼ turn of the Allen Key. DO NOT
USE cordless drivers or power drills as over-tightening can cause the head and foot end to bow.
STEP 3–Ensure the bed is square and then tighten the button head bolts using the allen key
provided.
STEP 4– Setting up the Gas Lift Struts & Posture Slat Frame
The Gas Lift Strut has been pre-fixed to your side rails. To connect them to the posture slats, first
remove the lock nut (shown below).

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[email protected]m.au W:www.silverlynx.com.au
STEP 5–Lift up the Gas Lift Arm and line up the bolt with the hole in the Support Strut.
STEP 6–Place the Support Strut over the bolt and secure using the lock nut (Steps 5 & 6
shown below).
STEP 7–Repeat Steps 4-6 on the other side rail.
STEP 8 –Identify the head end of your Posture Slat Frame by matching the bolt holes on the side
of your Posture Slats with the slots on the Gas Lift Struts (these will be bolted together in the next
step). Fix the Mattress Bar to the head end of the Posture Slat Frame as shown below. This will
ensure that your mattress will not slide into the bed head when accessing the gas lift storage.
STEP 9 –Place the Posture Slat Frame in position on top of the Gas Lift Struts so that the holes
on the Gas Lift Struts line up with the locator holes along the sides of the Posture Slat Frame.
STEP 10 –Slide mushroom head bolts through the holes and use nuts to secure onto the frame.
There are slots on the Gas Lift Struts to allow you to adjust the Posture Slat Frame. Use this
adjustment so that once the slats are ‘closed’, it rests on the cleat on the Foot End rail. (Note,
without mattress placed on top of Posture Slat Frame, your Gas Lift bed will stay in an ‘open’
position).
STEP 5
STEP 6

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[email protected]m.au W:www.silverlynx.com.au
STEP 11 –Fit Support Leg as shown below by fixing to the two locator holes on the under-side of
the Posture Slat Frame near the Foot End. Note this step is only necessary if you have either a
King Bed (you will install 2 Support Legs) or a Queen Bed (you will install 1 Support Leg). Smaller
beds (Double, King Single, and Single do not use a Support Leg.
STEP 12 –Fine tune the Support Leg/s by unscrewing the foot so that it sits roughly 5 –
10mm above the floor.
STEP 13 –Loop the Fabric Strap Handle around the foot end of the Posture Slat Frame as
shown below. This can now be used as a handle to lift your bed for access to the storage
space below.

Bomi Furniture P/L trading as Silver Lynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[email protected]m.au W:www.silverlynx.com.au
STEP 14 –’Close’ the Posture Slat Frame and place your mattress on top. Your Gas Lift
Bed is now ready to enjoy!
NOTES
•Button head bolts should be regularly inspected and may need to be retightened after a period
of time.
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your Silver Lynx product is crafted with care, properly maintained, it will mature over time
developing a rich deep patina enhancing its appearance. To get the best performance from your
Silver Lynx product, please follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended
periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the suite.
•Do not use cordless drivers or power drills to tighten your bed brackets, as over-tightening can
cause the foot end rail to bow.
Contact your retailer or our sales office for further information