SimpliFire SF-BI30-EB User manual

1SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
Model(s):
WARNING: To reduce risk of re, electrical shock, or personal injury, read all instructions
before using appliance.
Owner’s Manual
Installation and Operation
DO NOT DISCARD THIS MANUAL
NOTICE
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
SF-BI30-EB
SF-BI36-EB
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN
THIS PRODUCT.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE
TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE.
INSTALLER: DO NOT DISCARD THIS MANUAL -
LEAVE FOR HOMEOWNER - SAVE THESE INSTRUCTIONS
Congratulations!
Congratulations on selecting a SimpliFire Electric Fireplace, an elegant and clean alternative to wood & gas burning replaces.
The SimpliFire electric replace you have selected is designed to provide the utmost in safety, reliability, and efciency.

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
2
11IMPORTANT INSTRUCTIONS
WARNING! Risk of Fire! Risk of Burns!
Risk of Electrical Shock!
DO NOT:
• Install or operate damaged appliance
• Modify appliance
• Operate the appliance without fully assembling all
components
The following actions are strictly prohibited.
• Installation other than as instructed by Hearth &
Home Technologies Inc.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies Inc.
Hearth & Home Technologies Inc. disclaims any
responsibility for, and the warranty and agency listing will
be voided by the above actions.
WARNING! DO NOT operate replace before read-
ing and understanding operating instructions. Failure
to operate replace according to operating instructions
could cause re or injury.
WARNING! Improper installation, adjustment, al-
teration, service or maintenance can cause injury or
property damage. Refer to owner’s information manual
provided with this appliance. For assistance or additional
information consult a qualied installer, service agency or
your dealer .
NOTICE! This replace is not intended for use as a pri-
mary heat source and should not be factored as such in
residential heating calculations.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electric shock,
and injury to persons, including the following:
• Read all instructions before installing this appliance.
• This appliance is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes, etc. and
curtains at least 3 ft. (0.9 m) from the front of the appliance
and keep them away from the sides and rear
• Extreme caution is necessary when any appliance is used
by or near children or invalids and whenever the appliance
is left operating and unattended.
• Do not operate any appliance if it malfunctions. Disconnect
power at service panel and have appliance inspected by a
reputable electrician before reusing.
• Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock or
re, or damage the appliance.
• To prevent a possible re, do not block appliance connection
fan air intakes or exhaust in any manner.
• A appliance has hot and arcing or sparking parts inside. Do
not use it in areas where gasoline, paint, or ammable vapors
or liquids are used or stored.
• Use this appliance only as described in this manual. Any
other use not recommended by the manufacturer may cause
re, electric shock, or injury to persons.
• Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions, has been dropped or
damaged in any manner. Return appliance to authorized
service facility for examination, electrical or mechanical
adjustment or repair.
• Do not use outdoors.
• The appliance is not intended for use in bathrooms, laundry
areas and similar indoor locations. Never locate appliance
where it may fall into a bathtub or water container.
• Do not run cord under carpeting. Do not cover cord with
throw rugs, runners, or the like. Arrange cord away from
trafc areas and where it will not be tripped over. Do not
tightly coil cord.
• Always use properly grounded, fused and polarized outlets.
• Always use ground fault protection where required by
electrical code.
• To disconnect appliance, turn controls to “OFF” then remove
plug from outlet or turn off circuit.
• Always disconnect power before performing any cleaning,
maintenance or relocation of the appliance.
• To prevent a possible re, do not burn wood or other materials
in this appliance.
• To prevent electrical shock or re, always use a certied
electrician should new circuits be required.
• When transporting or storing the appliance, keep in a dry
place free from excess vibration and store to avoid damage.
• Avoid use of an extension cord because an extension
cord may overheat and cause a fire. However if you
have to use an extension cord, the cord should be No.
14 AWG minimum size and rated to not less than 1875
watts.

3SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
Safety Alert Key:
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Table of Contents
1 IMPORTANT INSTRUCTIONS
A. Important Information.............................2
B. Warranty.......................................4
2 GENERAL INFORMATION
A. Appliance Certication ............................5
B. California ......................................5
C. Unpacking and Inspecting Appliance ................5
D. Model and Serial Number Information ..............5
3 GETTING STARTED
A. Parts and Hardware .............................6
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6
C. Appliance Dimensions ............................ 6
D. Location ....................................... 7
E. Clearance to Combustibles ........................7
F. Electrical Supply Circuit Requirements ...............7
G. Installation of Top Stand-offs .......................7
4 INSTALLATION
A. Selecting Appliance Location .......................8
B. Appliance Preparation ............................9
C. Installation into Existing Fireplace ..................10
D. Installation into New Construction ..................10
E. Constructing the Chase ..........................10
F. Electrical Connection ............................10
G. Finishing Fireplace Wall .......................... 11
5 OPERATING INSTRUCTIONS
A. Manual Switch Function: .........................12
B. Operating by Remote Control. . . . . . . . . . . . . . . . . . . . . . 13
C. Resetting Temperature Cutoff Switch................13
6 MAINTENANCE
A. Maintenance ..................................14
B. Cleaning ......................................14
C. Electrical Wiring Diagram ......................... 14
D. Servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
E. Service Parts List ..............................15
F. Contact Information .............................17

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
4
SimpliFire™ WARRANTY
Hearth & Home Technologies, on behalf of its brand SimpliFire (”SimpliFire”), extends the following warranty
for electric fireplaces that were purchased from a SimpliFire authorized dealer.
WARRANTY COVERAGE:
SimpliFire warrants to the original owner of the SimpliFire fireplace, and to any transferee taking ownership of the Simpli-
Fire fireplace within 2 years following the date of original purchase, that the SimpliFire fireplace will be free from defects in
materials and workmanship at the time of manufacture for a period of 2 years. If a SimpliFire fireplace is found to be
defective in materials or workmanship during applicable warranty period, HHT will, at its option, repair or replace the
SimpliFire fireplace. SimpliFire, at its own discretion, may fully discharge all of its obligations under such warranties by
replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recover-
able under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions
and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized SimpliFire dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date.
WARRANTY CONDITIONS:
This warranty only covers SimpliFire fireplaces that are purchased through a SimpliFire authorized dealer or distributor. A
list of SimpliFire authorized dealers is available on the SimpliFire websites.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, batteries and the discoloration of glass.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) shipping or
improper handling; (3) improper operation, abuse, misuse, continued operation with damaged, corroded or failed
components, accident, or improperly/ incorrectly performed repairs; (4) environmental conditions (5) installation or use
of components not supplied with the appliance or any other components not expressly authorized and approved by
HHT; (6) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (7) interrup-
tions or fluctuations of electrical power supply to the appliance.
• Our obligation under this warranty does not extend to the SimpliFire fireplace’s capability to heat the desired space.
This warranty is void if:
• The fireplace is subject to or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemi-
cals.
• The fireplace is subjected to or operated in places with prolonged periods of dampness or condensation or weather.
Examples include but are not limited to outdoors, porches, and laundry rooms.
• There is any damage to the fireplace or other components due to water or weather damage.
LIMITATIONS OF LIABILITY:
• The owner’s exclusive remedy and SimpliFire’s sole obligation under this warranty, under any other warranty, express
or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will SimpliFire be liable for any incidental or consequential damages caused by defects in the appliance. Some
states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply
to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
EXCEPT TO THE EXTENT PROVIDED BY LAW, SIMPLIFIRE MAKES NO EXPRESS WARRANTIES OTHER THAN
THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION
OF THE EXPRESSED WARRANTY SPECIFIED ABOVE.
2040-645 4/20
B. Warranty

5SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
Note: The device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
MODELS: SF-BI30-EB, SF-BI36-EB
LABORATORY: CSA International
TYPE: Electric Air-Heaters Fixed and Location-Dedicated
Electric Room Heaters
STANDARD: UL 2021 (3rd Edition) CSA C22.2 No 46-13
A. Appliance Certication
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen-
tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
NOTICE: This installation must conform with local codes.
22 GENERAL INFORMATION
C. Unpacking and Inspecting Appliance
WARNING! DO NOT use this Electric Fireplace if any
part has been under water. Immediately call a qualied
service technician to inspect and to replace any part of
the electrical system if necessary. Keep plastic wrapping
away from children.
• Carefully remove the appliance and components from
the packaging. Discard packaging.
• Carefully inspect components for any damage.
• Reference parts list to verify all parts have been received.
• Report to your dealer any missing or damaged parts.
• Read all the instructions before starting the installation.
Follow these instructions carefully during the installation
to ensure maximum safety and benet.
Model Name: ___________________________________________ Date purchased/installed:__________________
Serial Number:__________________________________________ Location on replace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
We recommend that you record the following pertinent
information about your replace.
Homeowner Reference Information
B. California
WARNING: This product can expose you to Di-
(2-ethyl hexyl) phthalate, which is known to the
State of California to cause cancer and reproductive
harm. For more information go to: www.P65Warnings.
ca.gov.
D. Model and Serial Number Information
The model and serial number information is located on the
rating plate. The rating plate is located on the upper wall of
the appliance behind glass front.

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
6
33 GETTING STARTED
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Pliers
Hammer
Gloves
Phillips screwdriver
Safety glasses
Flat blade screwdriver
Level
Framing material
Framing square
Electric drill and bits (1/4 in.)
Reciprocating saw
C. Appliance Dimensions
B. Tools and Supplies Needed
Parts and Hardware List
Part Quantity
Fireplace 1
Instruction Manual 1
Remote Control 1
AAA Battery 2
Mounting Bracket 4
Rear Leveling Bracket 2
Screw ST4x8 8
Screw ST4x12 4
Power Cord Assembly
(for 120V only) 1
240VAC 4 Wire Conversion Plug 1
A. Parts and Hardware
3/4 IN
W1
W2
W3
W4
W5
D2
D1
H3
H2
H1
3-3/8 IN
1/2 IN
H4
units: inches
MODEL
SHELL SIZE TRIM SIZE VIEWING AREA CHASE SIZE
D2 H1 W1 W4 W5 W2 H2 W3 H3 H4 D1 W5
SF-BI30-EB 11 26-3/4 33 24 31 30 26-1/4 28-1/4 22-3/4 28-3/4 11-3/4 31
SF-BI36-EB 11 31-7/32 39 30 37 36 30-1/2 34-1/4 27-1/4 33-7/32 11-3/4 37

7SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
D. Location
When choosing a location for your replace ensure that
the general rules are followed:
• For best results, install out of direct sunlight.
• Power supply service must be installed within
proximity of electric replace prior to nishing to
avoid reconstruction.
• See Figure 3.C for appliance dimensions and to
determine location of appliance installation.
E. Clearance to Combustibles
The SimpliFire Built-in Series is a zero clearance design,
with the exception of the top of the unit when hard-
wired for 240V. Any insulation and vapor barrier should
be placed a minimum of 2" from the top of the rebox.
Bend the supplied stand-offs to a vertical position to
maintain this clearance.
Minimum Clearance to Combustibles
120V 240V
Sides.......................0 in..................0 in
Floor........................0 in..................0 in
Top..........................0 in..................2 in
Back........................0 in..................0 in
Front.......................36 in...............36 in
Mantels..........See Figure 3.1
F. Electrical Supply Circuit Requirements
Plan the location of the appliance so that it will have ad-
equate electric power. A 15 AMP, 60Hz circuit is required
for both 120V and 240V installations. Additional appli-
ances on the same circuit as this appliance may exceed
the current rating of that circuit. A dedicated circuit is not
required, but is preferred to prevent circuit breaker trips
or fuse failure.
Reference Section 4.F for more complete detail on com-
pleting electrical installation.
2 in.
2 in.
2 in.
6 in.
12 in.
Measurements from top surface
of the unit.
Figure 3.1 Minimum Vertical and Maximum Horizontal Dimensions of Combustible Mantels.
G. Positioning of Top Stand-offs
When this unit is to be hard-wired for 240V, a clearance
of 2 inches is required on the top of the unit. Bend the
supplied stand-offs on the top of the unit to a vertical
position to maintain this clearance.
Conrm electrical connection switch is properly
positioned to reect 120V or 240V, depending on wiring
choice.
WARNING! Risk of Fire! Keep electrical cords, drapery,
furnishings or other combustibles at least 3 ft. (0.9 m)
from the front of the electric replace.

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
8
44 INSTALLATION
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 4.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be locat-
ed out of trafc and away from furniture and draperies.
NOTICE: Illustrations reect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
D2
1/2 in.
1/2 in. D3
D1
W2
H1
W1
Figure 4.1 Clearance Requirements
This product can be built into new construction or an exist-
ing factory-built replace. Reference Sections 4.A - 4.D for
specic information for your installation.
MODEL W1 H1 D1 W2 D2 D3
(Table in Inches) 120V 240V
SF-BI30-EB 32 29 31 11-5/8 47-5/16 33-1/2 23-11/16
SF-BI36-EB 38 33-11/16 35-11/16 11-5/8 55 38-29/32 27-1/2
MODEL (V) (W) REMOTE (A)
SF-BI30-EB 120/208/240 1400/2100/2800 Yes 11.7/10.1/11.7
SF-BI36-EB 120/208/240 1400/2100/2800 Yes 11.7/10.1/11.7
ELECTRICAL SPECIFICATIONS:

9SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
BRACKET LOCATION
PRE-DRILLED
HOLES
LEVELING
BRACKETS
MOUNTING
BRACKETS
PRE-DRILLED
HOLES
B. Appliance Preparation
Install mounting brackets (4) by aligning them with the pre-
drilled holes located on the side of the appliance . Use two
screws (ST4 x 8) per bracket to secure to the appliance.
See Figure 4.2 and 4.3.
Installing leveling brackets (2) by aligning them to the preset
holes at the base of the appliance. Use two screws (ST4
x 8) per bracket to secure the appliance. See Figure 4.2.
Figure 4.2 Pre-drilled Hole Locations
Figure 4.3 Bracket Locations
E. Constructing the Chase
A chase is a vertical box-like structure built to enclose the
electrical appliance. Chases should be constructed in the
manner of all outside walls of the home to prevent cold
air drafting problems. The chase should not break the
outside building envelope in any manner.
Walls, ceiling, base plate and cantilever oor of the chase
should be insulated. Vapor and air inltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air inltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
D. Installation into New Construction
Position the replace within the opening in the framing.
Level the replace with shims if necessary. Attach the
replace to the framing with the two provided brackets
and screws or nails.
C. Installation into Existing Fireplace
1. Seal all drafts with non-berous insulation materials to
prevent debris or water from falling from the chimney
to electric replace.
2. Close or seal off the chimney ue and close damper
(if applicable) to prevent rain inltration.
3. Do not install in an existing replace that is prone to
dampness.
4. A provision must be made for the appliance to be
connected to power within existing rebox, or on an
adjacent wall.

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
10
F. Electrical Connection / Installation
Note: All wiring must be completed prior to nishing
the unit.
All electrical connections shall be performed by a
qualied electrician.
WARNING! Risk of Fire, Electrical Shock and Injury!
Electrical wiring must comply with local building electri-
cal codes and the latest edition of the NFPA 70 National
Electric Code (NEC) other applicable regulations.
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing the appliance. Wiring errors
can cause improper and dangerous operation. Verify
proper operation after servicing.
This appliance is designed to be hard-wired for 120VAC
or 240VAC. A supplied plug-in kit is also available for use
with a 120VAC grounded receptacle. The AC voltage sup-
ply wiring should be properly grounded. A dedicated cir-
cuit is recommended. Other appliances on the circuit may
cause the breaker to trip or fuse to blow when the appli-
ance is operating.
Hard-Wired Installation:
A 15 AMP circuit with a properly grounded outlet is
required for both 120VAC and 240VAC installations. Use
minimum size 14AWG Romex cable for the AC sup-
ply connection to 120 -240VAC, 60Hz, 15 AMP branch
circuit. Use copper wire only.
Note: The appliance must be electrically connected and
grounded in accordance with local building elec-
trical codes.
1. Remove terminal block cover plate located on the
right end of the appliance.
2. Install a wire strain relief bushing into the cover
plate.
3. Terminate type NM-B wire to the terminal block,
ensure connections are secure, and tighten the
strain relief. Use 3/32 slotted heat screwdriver, or
equivalent, to depress the spring loaded terminals
for the conductors.
For 120VAC Applications:
The following instructions must be followed to install
a 3-wire NM-B Romex cable to the terminal block
shown on Figure 4.4.
a. Connect the ground wire (green) to the ground
terminal.
b. Connect the line input neutral wire (white) to the
N terminal.
c. Connect the line input voltage wire (black) to the
L1 terminal.
d. Tighten each terminal screw rmly and make
sure that they are tight.
e. Make sure that no wire is connected to the L2
terminal.
Power Cord Installation
The appliance power cord has a 3-pin NEMA-5-15P
plug. The power cord should not be used unless a
grounded receptacle is available.
1. Remove the terminal block cover plate located on
the right end of the appliance.
2. Disconnect the terminal block from the four wires
inside the appliance. Wires are released by discon-
necting the conductor wire connector. Discard the
terminal block cover plate.
3. Connect the conductor wire connector to the
connector on the block supplied with the power cord
kit. See Figure 4.5.
4. Inspect that the correct voltage is selected on the
selector switch located behind the glass on the
ceiling of the unit. Failure to do so could damage the
product. See Figure 4.6.
5. Replace cord kit terminal block cover plate
and retaining screws.
For 240VAC Applications:
The following instructions must be followed to install
a 4-wire NM-B Romex cable to the terminal block
shown on Figure 4.4.
a. Connect the ground wire (green) to the ground
terminal.
b. Connect the line input neutral wire (white) to the
N terminal.
c. Connect the line input voltage wire (black) to the
L1 terminal.
d. Connect the line input voltage wire (red) to the
L2 terminal.
e. Tighten each terminal screw rmly and make
sure that they are tight.
4. Ensure all connections are tight and there are no
exposed wires. Tighten Romex strain relief and reat-
tach junction box cover plate.
5. Inspect that the correct voltage is selected on the
selector switch located behind the glass on the ceil-
ing of the unit. Failure to do so could damage the
product. See Figure 4.6.
6. Replace terminal block cover plate and retaining
screws.
Figure 4.4 Hard-wire Terminal Block

11SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
Figure 4.6 Finishing Dimensions
G. Finishing Fireplace Wall
Non-combustible materials may be used to nish up
to the replace glass frame. Ensure that you leave
adequate room to remove and replace the glass frame.
See Figure 4.6.
30 in.
26 1/4 in.
36 in.
30 3/4 in.
SF-BI30-EB Finishing Dimension SF-BI36-EB Finishing Dimension
WARNING! Ensure the power selector
switch is in the correct position. The switch
is located behind the glass on the ceiling
of the unit. Failure to do so could damage
the product.
Figure 4.5 Optional Power Cord Assembly
VOLTAGE SELECTOR SWITCH
Figure 4.6 Voltage Selector Switch
WHITE - N
YELLOW / GREEN - GRND
Wire Diagram
*THE RED WIRE IS NOT TO BE
CONNECTED TO THE POWER
CORD FOR 120VAC APPLICATIONS
RED* - L2
BLACK - L1

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
12
WARNING! Do not operate the unit if it is damaged or has
malfunctioned. If you suspect the unit is damaged, call
a qualied service technician to inspect and replace any
part of the electrical system if necessary.
Note: A harmless slight brief odor may occur during rst
use or after prolonged period of storage.
A. Manual Switch Function:
The appliance can be operated by both remote control
and manual button. Once the unit has been properly
connected to a grounded electrical circuit, the unit can
be turned ON by pressing the Flame button. In any ac-
tive Flame mode, the Heater button function is available.
If the Flame effect is OFF, there is no Heater button
function. See Figure 5.1.
Flame Button
By pressing the FLAME button, the unit will cycle
through four ame effects.
Heater Button
- Press the heater button to turn on heater. Appliance
will beep and illuminate 2 red LEDs.
- Press second time turns heater off.
NOTE:
There is a brief delay between the heater command and
the heating turning ON. When the appliance receives
a heater ON command, the appliance blower will turn
ON for 8 seconds before the heater turns ON. There is
also an 8 second delay between heater off and blower
shutdown.
55 OPERATING INSTRUCTIONS

13SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
ICON TITLE FUNCTION REMOTE LCD
DISPLAY
FIREPLACE RESPONSE
POWER
The POWER button will turn the
replace on. It will also put the
replace in a standby mode.
This will turn off all functions at
once but will hold the settings in
memory except Heater function.
The unit will turn on at the same
settings by pressing the power
button again.
LCD illuminates and
displays ame status
Icon and temperature
set point.
Fireplace emits single audible beep
to conrm command to transition to
ON or STANDBY state
FLAME
By pressing the FLAME button,
the unit will cycle through four
ame effects.
LCD illuminates and
displays ame status
icon.
Fireplace emits single audible beep
to conrm command to transition
between four FLAME states.
HEATER
Press Heater button once heater
turns on.
Press Heater button twice turns
off heater.
LCD illuminates
and displays heater
status icon.
Fireplace emits signal audible beep
to conrm command to transition
between ON and OFF. Fireplace
displays two red LEDs for 8
seconds to conrm command.
THERMOSTAT
Pressing the Temperature button
adjusts the heater’s response
to the ambient temperature
conditions in the room.
Temperature adjusts from 16 °C
- 28 °C (61 °F - 82 °F). Power
button must be on to set from °C
to °F. Hold for 3 seconds and the
LCD display from °C to °F.
Remote displays
the temperature. If
in Stand-by mode,
temperature displays
but cannot be
adjusted.
Fireplace emits single audible beep
to conrm command to change
desired temperature set point.
TIMER
Pressing the Timer button sets
the time desired for the replace
to run. The Timer can be set from
.5 hour up to 9 hours in 1 hour
increments.
Remote will display
the time setting
selected. If no timer
is set, there will be
no indicator.
Fireplace will emit single audible
beep to conrm command to
desired timer setting.
B. Operating by Remote Control
• Make sure batteries are properly installed in Remote
Control.
- Battery requirements 2 x AAA batteries
(included)
• The effective range of the remote is up to 13 ft.
• The remote control must be within the 13 ft. range and
also be pointed directly at the face of the appliance.
For best results, position the remote control within 45
degrees of the face of the appliance
C. Resetting Temperature Cutoff Switch
The heater is protected with a safety device to prevent
overheating. Should the heater overheat, an auto-
matic cutoff will turn the heater OFF. It will not turn ON
automatically without being reset. If it overheats for any
reason, it can be reset by:
1. Turn appliance to off
2. Shut-off power at circuit breaker.
3. Let appliance cool for 15 minutes.
4. Turn on power at circuit breaker.
5. Turn on appliance with touch pwer button or remote
control.
CAUTION: If you need to continuously reset the heater,
unplug the appliance and call your customer/technical
support.

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
14
A. Maintenance
WARNING! Risk of Shock! Always unplug the cord be-
fore moving or servicing. Do not immerse appliance in
water.
• Always turn OFF the appliance and disconnect the
cord from the electrical outlet before cleaning your
appliance.
• Light accumulated dust may be removed from the ap-
pliance with a soft cloth or vacuum cleaner.
• Wipe the exterior surfaces of the appliance occasion-
ally with a slightly damp cloth using a solution of mild
detergent and water. Dry thoroughly before operating
the appliance.
CAUTION! Do not allow water to run into the interior of
the appliance as this could create a re or electric shock.
Always disconnect electrical service before serving ap-
pliance.
• The fan motor is factory lubricated for life and will not
require further lubrication.
• Store appliance in a clean dry place when not in use.
WARNING! Risk of Fire! To reduce risk of re, do not
store or use gasoline or any other ammable vapors or
liquids in the vicinity of the appliance.
WARNING! Risk of Electrical Shock! Any other servic-
ing needed must be performed by an authorized service
representative. Do not attempt to service the unit your-
self.
B. Cleaning
Cleaning Glass
Dust particles can be removed by bufng lightly with a
clean dry cloth. Fingerprints and other marks can be
cleaned with a cloth dampened with a quality household
glass cleaner. The glass should be completely dried with
a lint free cloth or paper towel. Do not use abrasive clean-
ers on glass surface. Do not spray liquids directly onto
any surface.
Metal Surface
Dust particles can be removed by bufng lightly with a
clean dry cloth. A damp cloth can be used to clean paint-
ed surfaces. Do not use abrasive cleaners. Do not spray
liquids directly on to any surface,
66 MAINTENANCE
C. Electrical Wiring Diagram
See Figure 6.1.
Figure 6.1 Electrical Wiring Diagram
D. Servicing
Except for installation and cleaning described in this man-
ual, an authorized service representative should perform
any other servicing.
WARNING! Risk of Electrical Shock! Any other servic-
ing needed must be performed by an authorized service
representative. Do not attempt to service the unit your-
self.

15SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
Service Parts SF-BI30-EB
Beginning Manufacturing Date: April 2017
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth
and Home Technologies does not sell directly to consumers. Provide model number and serial number
when requesting service parts from your dealer or distributor. Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
1 Heater Assembly includes Control Board and Fan HEATER-BI30-B Y
2 Rotisserie Motor, Rod & 3 screws ROTISS-BI30-EB Y
3 LED Strips, 3 Strips LED-BI30-B Y
4Log/Grate Assembly LOGS-BI30-B Y
5 Refractory Kit REFRACT-BI30-B Y
6 Flame Screen FLAME-BI30-B Y
7 Front FRONT-BI30-EB Y
8 Glass GLA-BI30 Y
9 Remote REMOTE-ELECT-B Y
Stand-o󰀨, Base Set of 2 STANDOFF-ELEC-B
Hardware Bag HRDW-BI Y
Includes: Mounting Brackets, Screw (ST4 x 8), Screws (ST4 x 12)
Remote Receiver RECEIVER-ELECT
Installation Manual 2040-980
Plug-in Kit PLUGIN-ELECT-B
3/20
30” Electric Fireplace
#1 Heater Tray #2 Rotisserie Motor #3 LED Strips
#4 Log/Grate Assembly
#7 Front #8 Glass #9 Remote
#5 Refractory Kit #6 Flame Screen
E. Service Parts List

SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
16
Service Parts SF-BI36-EB
Beginning Manufacturing Date: April 2017
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth
and Home Technologies does not sell directly to consumers. Provide model number and serial number
when requesting service parts from your dealer or distributor. Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
1 Heater Assembly includes Control Board and Fan HEATER-BI36-B Y
2 Rotisserie Motor, Rod & 3 Screws ROTISS-BI36-EB Y
3 LED Strips, 3 Strips LED-BI36-B Y
4Log/Grate Assembly LOGS-BI36-B Y
5 Refractory Kit REFRACT-BI36-B Y
6 Flame Screen FLAME-BI36-B Y
7 Front FRONT-BI36-EB Y
8 Glass GLA-BI36 Y
9 Remote REMOTE-ELECT-B Y
Stand-o󰀨, Base Set of 2 STANDOFF-ELEC-B
Hardware Bag HRDW-BI Y
Includes: Mounting Brackets, Screw (ST4 x 8), Screws (ST4 x 12)
Remote Receiver RECEIVER-ELECT
Installation Manual 2040-980
Plug-in Kit PLUGIN-ELECT-B
3/20
36” Electric Fireplace
#1 Heater Tray #2 Rotisserie Motor #3 LED Strips
#4 Log/Grate Assembly
#7 Front #8 Glass #9 Remote
#5 Refractory Kit #6 Flame Screen

17SimpliFire • SF-BI30-EB, SF-BI36-EB • 2040-980 Rev. F • 4/20
SimpliFire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
F. Contact Information
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
Printed in China - Copyright 2020
DO NOT DISCARD THIS MANUAL
NOTICE
• Leave this manual with
party responsible for use
and operation.
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
Please contact your SimpliFire dealer or customer / technical support
(877-320-0730) with any questions or concerns.
For the location of your nearest SimpliFire dealer,
please visit www.hearthnhome.com.