Sindoh 5X Series User manual

Series
USER MANUAL
Read the User Manual before operating the
product, and keep the manual at
a convenient
place near the product.
3dprinter.sindoh.com
5X/
7
X
Read the User Manual before operating the
a convenient

Safety
Instructions
Be sure to observe the following instructions when using the device.
Warning: Failure to observe the instructions may lead to death or serious injury.
Directly plug the power cord in the receptacle on the wall. Do not use extension cord.
If the power cable or plug is worn or damaged, pull out the power plug.
The exposure of the interior of the machine can cause electric shock or burns.
Do not remove covers or screws other than specified in this manual.
Please be cautious. In the process of printing, the temperature of the nozzle and the heated
bed rise higher than 100 degrees Celsius.
Do not place the machine in a highly moist environment as it may cause deformation and
malfunction.
Avoid contact of electrical terminal with metal product such as necklaces, coins, keys,
watches, etc.
Do not hold the shaft for lifting or moving of the printer.
For the following situations turn off power and pull out the power plug
-
When in contact with liquid
-
When in need for a service or repair request
-
When the device cover is damaged
For the method of disposal contact local service center or use a proper collection site.
Please turn off power when leaving the office after business hours or in circumstances where
machine is unoccupied for a long period of time as it may cause abrupt fire accidents.
Caution: Failure to observe instructions may cause injuries or damages to property.
Protect device from humid or wet conditions e.g. rain, snow, etc.
Remove power cord from receptacle on the wall before moving device.
Be careful not to damage power cord while device is being translocated.
When removing the power cord, please pull the plug and not the power cable.
Be cautious of clips, staples and any other small metal objects from falling inside the device.
Please be cautious on safety when touching the interior of the machine, e.g. cleaning the
interior.
Do not dispose of device or consumables together with household waste.
For the method of disposal, please contact local service center or use a proper collection site.
Interior of device may be very hot. Please do not touch the part with “Caution: High
Temperature” sign or its surrounding areas as it may cause burns.
Our product maintains high quality standards and performance.
It is recommended to use genuine components only; components can be acquired from any
authorized distributors.
This equipment is not suitable for use in locations where children are likely to be present..

Before use
Thank you for purchasing our product.
This user manual contains detailed information about correct use of device and easy
maintenance to maintain the optimal state, and to contribute to the rationalization of office
work of your company.
Carefully read the user manual before using the device and keep close at hand.
In order to use device correctly and safely, please carefully note the precautions before use.
Prohibition and limitation
1. This User Manual has been created for the convenience of the user; actual product
may differ from image and explanations shown.
2. The contents of this user manual are subject to change without notice. We are not
responsible for the direct and/or indirect loss or damages caused by results of handling
or operating the product in any case and for results occurring from user’s negligence.
3. The copyrighted literary works can be duplicated and used for personal use or
household use and within the same parameter. In other cases than the
aforementioned, it is prohibited by law.
4. The above details present only a part of the applicable laws and regulations.
Details on these laws/regulations may not be stated as they are. We do not guarantee
its correctness and completeness. Please consult a legal advisor to check if the object
you intend to print is legal.
5. User is responsible for all loss derived from modification of the product executed by
the user or third party.
6. Font used in the user manual is the “NANUM” font provided by NAVER, and font used in the GUI
is the “Noto-sans regular” font provided by Google.

Contents
Before using the Machine
1. Preface -------------------------------------------------------------------------------------------------------------------------- 1
2. Conventions ------------------------------------------------------------------------------------------------------------------ 2
Symbols ------------------------------------------------------------------------------------------------------------------------ 2
3. Safety Information ---------------------------------------------------------------------------------------------------------- 3
4. Precautions ------------------------------------------------------------------------------------------------------------------- 5
4.1 Installation ---------------------------------------------------------------------------------------------------------------------- 5
4.2 Moving the Machine ---------------------------------------------------------------------------------------------------------- 6
5. Consumables Handling --------------------------------------------------------------------------------------------------- 7
5.1 PLA ----------------------------------------------------------------------------------------------------------------------------- 7
5.2 ABS ----------------------------------------------------------------------------------------------------------------------------- 7
5.3 Flexible -------------------------------------------------------------------------------------------------------------------------- 8
5.4 PVA ----------------------------------------------------------------------------------------------------------------------------- 8
6. Instructions for Use -------------------------------------------------------------------------------------------------------- 9
7. Ventilation ------------------------------------------------------------------------------------------------------------------- 10
8. Notices ----------------------------------------------------------------------------------------------------------------------- 11
9. Disposal of Used Battery ---------------------------------------------------------------------------------------------- 14
10. Wifi Module Disclaimer ------------------------------------------------------------------------------------------------- 15
11. USB Memory Disclaimer ----------------------------------------------------------------------------------------------- 17
Chapter 1 Preparations for Machine Operation
1. Machine Specifications ------------------------------------------------------------------------------------------------ 1-2
1.1 Printing ----------------------------------------------------------------------------------------------------------------------- 1-2
1.2 Temperature/Speed ------------------------------------------------------------------------------------------------------ 1-2
1.3 Machine ---------------------------------------------------------------------------------------------------------------------- 1-2
1.4 Software/Support --------------------------------------------------------------------------------------------------------- 1-2
1.5 Default Setting of Print layer Width ----------------------------------------------------------------------------------- 1-2
2. Basic Components ------------------------------------------------------------------------------------------------------ 1-3
3. Understanding the Device Parts ------------------------------------------------------------------------------------ 1-4
4. Installation (Product connection, Cartridge Setup and includes Software Installation) -------- 1-6
4.1 Device Connection -------------------------------------------------------------------------------------------------------- 1-6
4.2 Program Installation ------------------------------------------------------------------------------------------------------ 1-6
ⅰ

Chapter 2 UI Menu Functions
1. UI Menu Function description---------------------------------------------------------------------------------------- 2-2
1.1 CARTRIDGE ---------------------------------------------------------------------------------------------------------------- 2-3
LOAD ------------------------------------------------------------------------------------------------------------------------- 2-3
UNLOAD -------------------------------------------------------------------------------------------------------------------- 2-5
UNLOCK -------------------------------------------------------------------------------------------------------------------2-11
1.2 Settings -------------------------------------------------------------------------------------------------------------------2-14
EXTRUDER----------------------------------------------------------------------------------------------------------------2-15
BED LEVELING -----------------------------------------------------------------------------------------------------------2-17
Z OFFSET -----------------------------------------------------------------------------------------------------------------2-18
NOZZLE CLEANING AUT O------------------------------------------------------------------------------------------2-20
NOZZLE CLEANING MANUAL----------------------------------------------------------------------------------------2-22
NOZZLE CALIBRATION ---------------------------------------------------------------------------------------------------2-25
NOZZLE CHANGE------- ---------------------------------------------------------------------------------------------------2-30
X,Y,Z -------------------------- ---------------------------------------------------------------------------------------------------2-33
NETWORK -----------------------------------------------------------------------------------------------------------------2-34
BED LOWERING -------------------------------------------------------------------------------------------------------2-38
CLEANING CASE ---------------------------------------------------------------------------------------------------------2-39
TEST PRINT --------------------------------------------------------------------------------------------------------------2-41
GENERAL SETTING ------------------------------------------------------------------------------------------------------2-43
TIME SETTING ------------------------------------------------------------------------------------------------------------2-44
TIME ZONE ------------------------------------------------------------------------------------------------------------2-45
E-MAIL ----------------------------------------------------------------------------------------------------------------------2-45
WEB ------------------------------------------------------------------------------------------------------------------------2-49
S/W UPDATE -------------------------------------------------------------------------------------------------------------2-50
CLOUD ---------------------------------------------------------------------------------------------------------------------2-52
OPEN MATERIAL --------------------------------------------------------------------------------------------------------2-53
1.3 Information -----------------------------------------------------------------------------------------------------------------2-57
ⅱ

Chapter 3 Printing
1. Printing ---------------------------------------------------------------------------------------------------------------------- 3-2
1.1 Printing from USB Flash Drive ----------------------------------------------------------------------------------------- 3-2
1.2 Printing Via PC ------------------------------------------------------------------------------------------------------------- 3-8
1.3 Print Job Management -------------------------------------------------------------------------------------------------- 3-8
1.4 Printing with Two Types of Filamentst ------------------------------------------------------------------------------3-10
1.5 Changing Filaments ----------------------------------------------------------------------------------------------------3-10
Chapter 4 Printed Output Check
1. Printed Output Check --------------------------------------------------------------------------------------------------- 4-2
1.1 Detaching Printable ------------------------------------------------------------------------------------------------------- 4-2
1.2 PVA Filament Removal Guide ----------------------------------------------------------------------------------------- 4-4
1.3 Improving Printing Quality ---------------------------------------------------------------------------------------------- 4-4
2. When Printer Cannot be Turned On ------------------------------------------------------------------------------- 4-5
3. If problems persist ------------------------------------------------------------------------------------------------------ 4-6
Chapter 5 Appendix
1. Type of Consumables (Material, Color) ------------------------------------------------------------------------- 5-2
ⅲ

Before using the
Machine
1. Preface
This User Manual describes detailed explanations and points to note in connection with operating and using
the machine. Please read the User Manual carefully before using machine, and keep it for reference purpose.
Important
-
The content of the User Manual is subject to change without any prior notification.
Sindoh shall not be liable for consequential, special, indirect damages or losses caused by the handling or
operating of the machine or by the user’s negligence.
-
Copyrighted works can be printed and used for home and/or personal use; other usage is prohibited by
law.
-
The above details present only a part of the applicable laws and regulations and the details of the law
may not be stated as they are. Sindoh is not responsible for its correctness and completeness.
Please consult your legal advisor to check if the object you intend to print is legal.
Note
-
The User Manual may include a little different descriptions of the machine from the actual one.
Some options may not be available in some countries. Please contact local distributor for details.
Some standard units are optional in some countries.
Please consult your local service center.
-
In some countries some models are not available.
Please consult your local sales office.
-
This manual uses metric units of measurement
1

Before using the Machine
2. Conventions
Symbols
This manual uses the following symbols and meanings.
Warning
-
Indicates importance safety notes.
Ignoring these notes could result in serious injury or death.
Be sure to read these notes carefully for your safe operations of the machine.
Caution
-
Indicates important safety notes.
Ignoring these notes could result in minor injury, or damage to the machine or to property.
Be sure to read these notes for your safe operations of the machine.
Important
-
Indicates points to pay attention to when using the machine, and explanations of likely causes of filament
misfeeds, damage to originals, or loss of data.
Be sure to read these explanations before operating the machine.
Note
-
Indicates supplementary explanations of the machine`s functions, and instructions on resolving user errors.
Reference
-
This symbol is located at the end of sections. It indicates where you can find further relevant information.
[ ]
Indicates the messages or menus that appear on the machine`s LCD display panel.
Indicates the names of each function key on the machine control panel and the display window.
2

Before using the
Machine
3. Safety Information
Plug the power cord into a properly grounded outlet which is near and quickly accessible from the machine.
Do not use or place the machine in wet or humid environment.
Caution Hot Surface
- When you touch your body with this part, you are burned.
- To avoid burns, follow the instructions below.
〮 The inside of the machine may be hot. To reduce the risk of injury from a
hot component, allow some time to cool down.
(Please be cautious of getting burns during printing as the Nozzle and the
heating bed will maintain a high temperature of over 100 degrees.)
〮
Do not put any portion of your body or objects on any part during machine operation as the motor
and bed can be in very high temperature and can cause burns/injuries. Please be cautious.
〮
When the power is on, do not let any of your body touch the machine except the bed.
If you have to touch the bed while the power is on, please do so after the bed temperature has
been lowered to room temperature.
〮
If you have to touch any parts other than the bed, please do so after the bed and nozzle temperature
have been lowered to room temperature.
〮
After the printer has finished printing, check the LCD screen and built-in speaker.
Do not touch the bed or the bed handle unitl you are told you can touch the bed.
Caution Electric Shock
- Contact with this part may result in electric shock.
- To avoid electric shock, follow the instructions below.
〮
Proceed your work after turning off the machine and unplugging the power cord
from the outlet in case of accessing the system board, or installing hardware or
optional memory devices. If the machine is connected with other device, turn it
off and separate the cables from the machine.
〮 This product has been designed, tested and approved to meet strict safety
requirements of international safety standard. Some safety features of parts may not be
guaranteed. Sindoh is not liable for problems caused by using an unauthorized spare parts or
consumables.
〮
Disconnect the power cord and all the cables connected to the machine to prevent from any
electrical shock when cleaning the outside or inside of the machine.
〮 Be sure to turn off the power before removing the nozzle from the machine. Electrical damage to the
internal parts of the nozzle may occur.
Caution Pain
- Do not twist, fold, step or place heavy objects on the power cord.
-
Be careful with the power cord peeled off or overloaded.
-
Do not let the power cord pinched by furniture or walls.
-
Misusing the cord could result in fire or electrical shock.
-
Check the cord regularly. When checking the cord, unplug the cord from the outlet first.
-
Please consult a qualified engineer for services or repairs not stated in this User Manual.
3

Before using the Machine
Caution Pain
-
Contact with this part may cause
-
To prevent pain
or damage to the equipment, follow the instructions below
• Do not open the front
and
• Do not open the side/
rear cover or touch
during machine operation.
• When the power is on,
do
the bed.
• If you have to touch
any parts other than
power off, removing
the power
temperature have been
lowered
• Turn the power switch
off,
• Unplug and release all
the cords and
• Only use the power
cords provided
• Do not put any portion
of
will
be in operation and
moving.
or damages to
the machine.
• If any problems
occur(malfunction,
operation, quickly
press the pause
of the touch
screen located
Nozzle Bed
Caution Pain
- When you
put the head in the machine during operation,
-
To prevent pain
or damage to the equipment, follow the instructions below
•
This part moves up and down. D
• Do not open the front
door during
• If you have to get in the
machine for maintenance, please do so after turning the power off,
removing the power cord from the plug and after the bed and nozzle temperature have been
lowered to room temperature.
Caution Pain
-
When you open the top
door it may fall and cause
- To prevent pain
or damage to the equipment, follow the instructions below
•
When opening the door, be careful of the door falling.
• When closing the door,
make sure that it is assembled in the correct position
4
Contact with this part may cause
pain.
or damage to the equipment, follow the instructions below
.
and
top door during machine operation.
rear cover or touch
any parts of the extruder unit
during machine operation.
do
not let any of your body touch
the machine except
any parts other than
the bed, please do so
after turning
the power
cord from the plug and after the bed and
nozzle
lowered
to room temperature.
off,
and then unplug the power cord from the power
the cords and
cables before moving the machine.
cords provided
with this
machine or cords that are approved
of
your body or objects during machine operation,
as the bed,
moving.
Small objects such as necklace, hair,
etc may cause
the machine.
occur(malfunction,
body part being caught inside
the machine,
press the pause
[Pause] or stop [Stop] button located on
screen located
on the bottom right of the upper
side.
UI
put the head in the machine during operation,
it may cause pain.
or damage to the equipment, follow the instructions below
.
This part moves up and down. D
o not put the head in the machine during operation.
door during
printing.
machine for maintenance, please do so after turning the power off,
removing the power cord from the plug and after the bed and nozzle temperature have been
door it may fall and cause
pain.
or damage to the equipment, follow the instructions below
.
When opening the door, be careful of the door falling.
make sure that it is assembled in the correct position
.
the machine except
after turning
the
nozzle
outlet.
machine or cords that are approved
by the manufacturer.
as the bed,
motor,
nozzle
etc may cause
personal injuries
the machine,
etc) during machine
the on the bottom right
machine for maintenance, please do so after turning the power off,
removing the power cord from the plug and after the bed and nozzle temperature have been

Before using the
Machine
Caution Pain
-
Contact with this part may cause pain.
-
To prevent injury or damage to the equipment, keep away from this part during
operation.

4. Precautions
4.1 Installation
Warning
-
Install the machine in a well
You can small odor during
machine operation.
machine is located is not
ventilated,
Important
-
Install the machine with its vents spaced at
Secure properly sufficient
space around the machine for
Use the machine at
temperatures of
Do not install or use the machine outdoo
Top View
100 mm 100 mm
100 mm
ventilated area.
machine operation.
It should not be
harmful; howeve
ventilated,
make sure to ventilate the
area appropriately
Install the machine with its vents spaced at
least 10 cm away from walls and other equipments.
space around the machine for
easy ventilation and operation.
temperatures of
16 ~ 29 and relative humidity of 20% ~
70%.
Do not install or use the machine outdoo
r.
Side V
iew
100 mm
1
6
9
0 mm
harmful; howeve
r, if the area of where the
area appropriately
time to time.
least 10 cm away from walls and other equipments.
easy ventilation and operation.
70%.
iew
500 mm
5

Before using the Machine
4.2 Moving the Machine
Warning
-
Before moving
the machine,
When moving the printer, it
is
- Hold the bottom handles of
Bend your knees enough
to
-
The unit is heavy
. Make sure to
4.3 Power Switch
Before turning the power switch on, check that
the power on by
push the power switch to "
turn the power off, push the
power switch to "○"(OFF) position.
│for "ON" IEC 60417-
5007 (DB:2002
○ for "OFF" IEC 60417-
5008 (DB:2002
The Switch used for this
machine meets the requirements on the symbols and complies with
standard. But
the horizontal straight bar is meaning the Power "ON" because its orientation is turned 90º to
the counterclockwise. Please
don't confuse the meaning of
Switch standard
IEC 61058-1
Symbol for the "OFF" position or the direction of actuation to the "OFF" position
Symbol for the "ON" position or the direction of actuation to the "ON" position
Warning
-
Do not plug or unplug the power cord or touch the power switch with wet hands. It may cause an electrical
shock.
6
the machine,
be sure to unplug the power cord from the outlet.
is recommended that four people lift and
move the printer
the machine when moving it.
to
protect your spine when lifting the machine.
. Make sure to
carry with four or more people.
Handle
Before turning the power switch on, check that
the power cord is connected to the
socket tightly. Then, turn
push the power switch to "
│
"(ON) position at the right on rear side of the
power switch to "○"(OFF) position.
5007 (DB:2002
-10)
5008 (DB:2002
-10)
machine meets the requirements on the symbols and complies with
the horizontal straight bar is meaning the Power "ON" because its orientation is turned 90º to
don't confuse the meaning of
the horizontal straig
ht bar "─".
Symbol for the "OFF" position or the direction of actuation to the "OFF" position
– circle,
Symbol for the "ON" position or the direction of actuation to the "ON" position
-
straight bar, │
Do not plug or unplug the power cord or touch the power switch with wet hands. It may cause an electrical
move the printer
for safety.
socket tightly. Then, turn
"(ON) position at the right on rear side of the
Machine. To
machine meets the requirements on the symbols and complies with
its
the horizontal straight bar is meaning the Power "ON" because its orientation is turned 90º to
ht bar "─".
○
straight bar, │
Do not plug or unplug the power cord or touch the power switch with wet hands. It may cause an electrical

Before using the
Machine
Important
-
Once you turn the power off, wait 5 seconds or longer to turn the power on again.
-
If you are not using the device for a long time or if you are moving the device, turn the power off
and unplug the power cord from the outlet.
5. Consumables Handling
Warning
-
Do not burn the Cartridge unit or filament. It may be a cause of big fire or burn by ignition.
Caution
-
Keep them out of the reach of children.
-
If skin irritation occurs after touching the filament, please see a doctor.
Important
-
Do not keep the cartridge unit in the following places.
• Exposed to fire
• Exposed to direct sunlight;
• Where temperature or humidity may rise;
• Where sharp change of temperature may occur;
• Covered with dust;
• Inside a vehicle for extended time.
-
Keep cartridges away from physical impact or vibration.
-
Do not unpack cartridges until you are just ready to use them.
5.1 PLA
It is a material that can be easily printed by the users using the 3D printer for the first time. You can easily print va-
rious colors and complex shapes. Ambient temperatures above 50 ° C can cause material properties to change,
causing the material to expand or scatter. PVA can be used as a support material.
Nozzle temperature: 200 ° C
Bed temperature: 60 ° C
Printing Speed: 40mm / s
Color: White, Black, Gray, Red, Yellow, Green, Blue, Pink, Purple
Storage: Store in cartridges with the silica gel that was included in the purchase.
5.2 ABS
Widely used in 3D printers, it has more rigidity and heat resistance than PLA. Due to the high temperature of the
nozzle and the air when printing, printing are not available with other materials. ABS material can be deformed by
shrinkage when the temperature in the cabin drops during printing. Particularly when printing a wide output surface to
the bed, shrinkage may occur at the corners.
Nozzle temperature: 230 ° C
Bed temperature: 90 ° C
Output speed: 40mm / s
Color: white, black, gray, red, yellow, green, blue
Storage: Store in cartridges with the silica gel that was included in the purchase.
7

Before using the Machine
5.3 Flexible
When using flexible materials, clean the inside of the nozzle after the filament load. Even if the inside of the nozzle is
cleaned, if the inside of the nozzle has debris, the nozzle may be clogged or the filament may be transported. (Refer
to P. 5-3 “1.5 Cleaning the Inside of the Nozzle”.)
Be careful because it is difficult to set the output condition compared with PLA and ABS materials. Warp or spider
web may occur at output.
Flexible materials can cause twists in the extruder or inside the cartridge rollers. (Refer to P. 5-14 “3.5 Solution for
Notification 401”.)
Nozzle temperature: 240 ° C
Bed temperature: 60 ° C
Output speed: 40mm / s
Color: white, red, yellow
Storage: Store in cartridges with the silica gel that was included in the purchase.
5.4 PVA
PVA material is water-soluble support material. It is used with PLA and can be melted and removed when the printing
is complete. (Refer to P. 4-4 “1.2 Removing PVA Filaments”.)
Even when PVA material is used, it may cause filament transport problem due to debris inside the nozzle. Please
clean the inside of nozzle after loading like flexible material. (Refer to P. 5-3 “1.5 Cleaning the Inside of the Nozzle”.)
Due to the large surface flow resistance of the material itself, filament transport may be a problem. (Refer to P. 5-14
“3.5 Response to Occurrence of Notification 401”.)
Caution
-
Carbonization may occur inside the nozzle during long-term output, so please clean the inside of the
nozzle periodically. Because it is very sensitive to moisture, please use in an environment with less than
50% humidity.
Nozzle temperature: 230 ° C
Bed temperature: 60 ° C
Output speed: 40mm / s
Color: Translucent White
Storage: Put the PVA filament and the silica gel in the zipperbag provided so that they would not be exposed to air
during storage.
Important
-
Please note that you shall follow our technical information or support in this manual at your own discretion
and risk.
We are not responsible for the use and handling of PVA filaments other than those described in this manual.
PVA filament specifications can be changed without any notice.
8

Before using the
Machine
6. Instructions for Use
Caution
-
The nozzle and the bed that are inside the machine are very hot during machine operation.
Please be cautious not to touch the nozzle or the bed during removal of the printed objected or during
inspection of the machine inside. It may become the cause of injuries or burns.
-
Never operate the machine in the way this manual does not specifically instruct.
Notification for California customers, USA
Warning
-
This product uses chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. This appliance and its accessories can cause low-level exposure to chemicals
during operation, which can be reduced by operating the appliance in a well ventilated area.
Caution
-
Do not open the rear/side cover or touch any parts of the extruder unit during machine operation to
prevent personal injuries of damages.
-
If you need inspection of the extruder unit, turn off the power and disconnect the power cord and follow
the instructions below.
Open the side door.
Remove 5 screws.
Remove the cover upward.
Remove filaments that ara blocked.
9

Before using the Machine
7. Ventilation
Caution
-
Use the machine in a place with good ventilation. If the machine is used in a place without good
ventilation, this may be harmful for your health. Ventilate it on a regular basis.
-
Do not block vents. Inappropriate cooling may lead to high temperatures inside the machine.
-
In general, a new machine may produce small amount of gaseous components, so ensure good
ventilation when the machine is used for the first time. If the machine is in operation for an extended
time, do not stay in the same room for a long time.
10

Before using the
Machine
8. Notices
❖ Noise Emission Level
The following are measured in accordance of ISO 7779 and reported to meet ISO 9296.
Some modes may not be available in your purchased products.
Average Sound Pressure at 1 Meter Away
Printing 50dBA(Normal Print Condition - Printing speed 40 mm/s, Travel speed 130 mm/s)
Standby under 40 dBA
❖ Temperature/Humidity
Operation
16 °C ~ 29 °C 20%RH~70%RH
Shipping -30 °C ~ 50 °C, 15%RH~95%RH(for 0 °C or lower temperature, room’
s temperature should be higher
than the outdoor’s; must not touch the floor)
Storage -30 °C ~ 50 °C, Below 80%RH(No condensation, must not touch the floor)
❖ Disposal of The Products
Do not dispose the machine and consumables together with household wastes.
For disposal or recycling, contact your local sales office.
❖ EMI(Electromagnetic Interference) Notice
This machine complies with the limits for Class A.
Class A (Industrial Device) : This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC COMPLIANCE STATEMET
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, Including interference that may cause undesired operation.
INFORMATION TO USER
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This
equipment generates
uses and can radiate radio
frequency
energy and, if not
installed
and used in
accordance
with the
instructions,
may cause harmful
interference
to radio
communications. However,
there
is no
guarantee
that
interference
will not occur in a
particular installation.
If this
equipment
does cause
harmful
interference
to radio or
television reception,
which can be
determined
by turning the equipment
off and on, the user is
encouraged
to try to correct the
interference
by one m ore of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-
Consult the dealer or an experienced radio/TV technician for help.
11

Before using the Machine
CAUTION
Any changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
This product has the certification issued under the authority of the FCC by one of Certification
Body(TUV Rheinland). FCC ID: 2AB83-7X.
❖ Wireless LAN Specifications
The wireless device may be affected by electromagnetic interference so it should not be used for life
saving services.
❖ WLAN Notice
Exposure to radio frequency radiation
The following notice is applicable if your printer has a wireless network card installed.
The radiated output power of this device is far below the FCC radio frequency exposure limits.
A minimum clearance of 20 cm (8 inches) must be maintained between the antenna and any persons for
this device to satisfy the RF exposure requirements of the FCC.
❖ Power Consumption
Power Consumption of the Products
The below table shows power consumption.
Mode
Description
Power Consumption(W)
Printing A device is printing using electronic input data. Max. 1000W
Standby A device is in standby mode. Max. 750W
Power On A power plug is plugged into the outlet with the machine’s
switch on.
15W
Power Off A power plug is plugged into the outlet with the machine’s
switch off.
0.5W
The above power consumption is the hourly average value.
Instant power consumption can be much higher than the average value.
Deactivated Mode
The machine consumes power even in the deactivated mode. Unplug the power cord to completely stop the
power consumption.
Total Energy Usage
It would be useful to calculate the Total energy usage of the machine.
Since the electricity bill is charged in Watt unit, you have to multiply time spent in each mode by power
consumption in order to calculate the energy use.
Total energy usage is the sum of energy used in each mode.
Condensation
Dramatic change of the ambient temperature may produces water droplets on the interior and exterior of the
machine.
Wipe
the
water droplets
on the
outer surface,
but for the
inside please
let
them
dry off by
leaving
front
door and cover
opened.
12
. FCC ID : 2AB83-7X.

Before using the
Machine
13