
Prepare outdoor camera for installation
Siqura HSD820 Series
High-speed 1080p PTZ dome camera series
Quick Start Guide
© Siqura B.V. 2015
Version 2.1 (132101-2a)
HSD820 QSG (MW10)
Outdoor camera mounting requirements
Install outdoor camera with wall mount
www.siqura.com
www.tkhsecurity-usa.com
Figure 1 Outdoor camera package contents
Quick Start Guide
and two leaflets
Dome camera with
outdoor mount kit
Figure 5 WM01A Mini Wall Mount
Use one of two types of Siqura mounts to install an outdoor HSD820 on a wall:
WM01A Mini Wall Mount
WM07 Long Wall Mount
Figure 6 WM07 Long Wall Mount
The mini wall mount and the long wall mount can be installed
onto a box mount if extra space for the cables is required.
Outdoor installation requires the following items:
Dome camera
Supplied waterproof boot
Wall mount (optional accessory)
Screws and screw anchors
Screwdriver and drill
To mount the outdoor HSD820 with a wall mount
1. Make a hole in the wall or metal access plate for the cables and secure the
supplied cable gland in the wall.
2. Ensure that the weather resistant gasket is correctly attached to the mount.
3. Thread the cables through the wall mount and screw it onto the wall.
4. Attach the waterproof boot to the wall mount.
5. Thread the cables through the outdoor tube adaptor and fix it to the wall mount
with the supplied screws and washers.
6. Clip the safety wire to the dome camera.
7. To keep insects out, block the cable entry hole with the supplied sponge.
8. Connect the cables to the dome camera.
9. Attach the dome to the outdoor tube adaptor and fasten them together with the
supplied screws.
Warning: Fully torque down the mounting bolt that attaches the
WM02 tube adapter to the mounting bracket to prevent any
movement of the camera due to wind, vibration, etc. Make sure
the camera cannot move at all in its bracket after installation. Any
movement of the camera in its bracket can compromise positional
accuracy.
Figure 2
Indoor camera
package contents
To wire the camera, use the images showing the positions of the switches and
connectors (below) and the cable pin definition diagrams (next section).
See accompanying leaflets: “Install the
HSD820H2/H3 network connector” and
“Safety Instructions”
Table 1 Connector definition
It is necessary to configure the power, alarms, and audio before connecting
the dome camera to other devices. The switches used for configuring these
settings are located on the bottom of the camera. The indoor and outdoor
models have slightly different configurations, but these connectors are in
approximately the same place on each camera.
Connect the power core through the
supplied power adapter.
Table 2 Connector C - Power
Use the pin definition below to set up
audio.
Table 3 Connector F - Audio
Table 4 Connector B –Alarm I/O
Use the pin definition
on the right to set up
Alarm I/O.
Figure 7 WM06 Wall Box Mount
To prepare the HSD820 for installation
1. Remove the outdoor tube adaptor by rotating counter clockwise (figure 8a).
2. Rotate to remove the protective cover.
3. Make a note of the IP address on the label attached to the cylindrical heat sink.
4. Remove the PE cloth and take off the lens cap.
5. Generously apply the supplied lubricant to the optical cover’s waterproof boot to
ensure an IP66 quality installation (figure 8b).
6. Loosen the screw head alignment pins on the dome cover by turning clockwise
and line up the alignment pin and screws on the optical cover with the holes in
the dome body.
7. Attach the optical cover to the dome body by pressing gently down on the sides
of the dome cover (figure 8c).
8. Turn the screw head alignment pins counter-clockwise with a suitable
screwdriver to lock the dome into place and secure the dome with the included
Phillips-head or TORX screw.
Figure 8a/b/c Remove the outdoor tube adaptor (left). Lubricate the optical cover’s
waterproof boot (centre). Attach the optical cover to the dome body (right).
Installation requires the following tools:
Dome camera
Supplied waterproof boot
Wall mount
Screws and screw anchors
Screwdriver and drill
M4 screws (5x)
and anchors (5x)
Note: Subject to modification. Actual product and accessories may differ in appearance.
Note: You can order wall mounts separately.