Siqura FD360IR Series User manual

001B08ZXZ1A3
FD360IR
High-Definition 6 MP
Fisheye Camera with D/N and IR
Installation Manual
Ver. 1.3.1

2
Note: To ensure proper operation, please read this manual thoroughly before using the product and retain the information
for future reference.
Copyright © 2015 Siqura B.V.
All rights reserved.
FD360IR
Installation Manual v1.3.1 (151703-1.3.1)
MW10
Nothing from this publication may be copied, translated, reproduced, and/or published by means of printing,
photocopying, or by any other means without the prior written permission of Siqura.
Siqura reserves the right to modify specifications stated in this manual.
Brand names
Any brand names mentioned in this manual are registered trademarks of their respective owners.
Liability
Siqura accepts no liability for claims from third parties arising from improper use other than that stated in this manual.
Although considerable care has been taken to ensure a correct and suitably comprehensive description of all relevant
product components, this manual may nonetheless contain errors and inaccuracies. We invite you to offer your
suggestions and comments by email via [e-mail]. Your feedback will help us to further improve our
documentation.
How to contact us
If you have any comments or queries concerning any aspect related to the product, do not hesitate to contact:
Siqura B.V.
Zuidelijk Halfrond 4
2801 DD Gouda
The Netherlands
General : [phone]
Fax : [phone]
E-mail : [e-mail]
WWW : www.siqura.com

3
Table of Contents
1. Overview................................................................................................................................4
1.1 Features......................................................................................................................4
1.2 Package Contents .......................................................................................................5
1.3 Dimensions..................................................................................................................7
1.4 Connectors (Indoor Only).............................................................................................9
1.5 All-in-One Cable (Optional)........................................................................................10
1.6 Function Cables (Outdoor Only) ................................................................................11
2. Camera Cabling...................................................................................................................12
2.1 Power Connection .....................................................................................................12
2.2 Ethernet Cable Connection........................................................................................12
2.3 Waterproof Cable Connector .....................................................................................13
3. System Requirements ........................................................................................................15
4. Access Camera ...................................................................................................................16
5. Setup Video Resolution......................................................................................................20
6. Configuration Files Export/Import .....................................................................................21
7. Tech Support Information ..................................................................................................22
7.1 Delete the Existing Siqura Viewer..............................................................................22
7.2 Setup Internet Security..............................................................................................23

4
1. Overview
The Ultra High Definition Multiple Streams Fisheye IP Camera is a
high-resolution surveillance solution featuring 180° panoramic view (wall mount)
or 360° panoramic view (ceiling mount) without blind spots. The camera
supports 1080p streaming at 60 fps which allows the videos to be viewed
smoothly. Moreover, the Edge Dewarping function of the camera can dewarp
the fisheye source images. With this feature, the dewarped images in
panoramic view or other different viewing modes can be recorded. Furthermore,
with the IR LED module, the camera can deliver clear images in low-light
conditions. For more features of this camera, see below.
1.1 Features
Progressive Scan CMOS Sensor
Software Dewarping-
Single Stream, 6M Real-time
Dual Streams, Full HD 1080p 60 fps
Edge Dewarping, Up to 4M Resolution Real-time
Quad Streams Compression-
H.264 Baseline / Main / High Profile + MJPEG
360° Panorama View
ePTZ
Quad View
Tampering Alarm
Wide Dynamic Range
Motion Detection
Privacy Masks
Day/Night (ICR)
IR LED Module
Built-in MIC & Speaker
Weatherproof (IP66 International)*
microSD Support
ONVIF Support
(*) Optional

5
1.2 Package Contents
Indoor
Ultra High Definition
Multiple Streams
Fisheye IP Camera
Self-Tapping Screw
(x3)
Plastic Anchor
(x3)
Security Screw
(x1)
Security Torx
Power Terminal
Block (x1)
Quick Guide
CD
Function Cable (Optional)
NOTE: The supplied self-tapping screws are for soft substance/material
installation such as wood. For other installation environments, such as a
cement wall, it is required to pre-drill and use plastic anchors before
fastening the supplied self-tapping screws on the wall.

6
Outdoor
Ultra High Definition
Multiple Streams
Fisheye IP Camera
Self-Tapping Screw
(x3)
Plastic Anchor
(x3)
Security Screw
(x1)
Security Torx
Power Terminal
Block (x1)
Quick Guide
CD
NOTE: The supplied self-tapping screws are for soft substance/material
installation such as wood. For other installation environments, such as a
cement wall, it is required to pre-drill and use plastic anchors before
fastening the supplied self-tapping screws on the wall.

7
1.3 Dimensions
The dimensions of the camera are shown below.
Indoor

8
Outdoor

9
1.4 Connectors (Indoor Only)
Loosen the security screws and open the cover to reach the connectors.
The diagram below shows the connectors of the camera. The definition for each
connector is as follows.
No.
Connector
Pin
Definition
Remarks
1
Power
DC 12 V
1
DC 12 V
Power connection
2
Ground
AC 24 V
1
AC 24 V 1
2
AC 24 V 2
2
RJ-45
-
For network and PoE connections
3
Alarm & Audio I/O
-
Refer to the Alarm & Audio I/O in the table under
All-in-One Cable (Optional).
4
Default Button
-
Press the button with a proper tool for at least 20
seconds to restore the system.
5
microSD Card Slot
-
Insert the microSD card into the card slot to store
videos and snapshots. Do not remove the microSD
card when the camera is powered on.
NOTE: It is not recommended to record with the microSD card for 24/7
continuously, as it may not be able to support long term continuous data
read/write operations. Contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.

10
1.5 All-in-One Cable (Optional)
No.
Connector
Pin
Definition
Remarks
1
Alarm & Audio I/O
1
Alarm Out +
Alarm connection / Two-way
audio transmission
2
Alarm Out –
3
Alarm In +
4
Alarm In –
5
Audio Out
6
GND
7
-
8
Audio In
2
Audio I/O
Pink
Audio In
Two-way audio transmission
Green
Audio Out
3
Alarm I/O
(4-Pin Terminal Block)
1
Alarm In –
Alarm connection
2
Alarm In +
3
Alarm Out –
4
Alarm Out +

11
1.6 Function Cables (Outdoor Only)
No.
Connector
Pin
Definition
Remarks
1
Audio I/O
Pink
Audio In
Two-way audio transmission
Green
Audio Out
2
Power (DC 12V / AC 24V)
(2-Pin Terminal Block)
Black
AC 24 V –
Power connection
DC 12 V –
Red
AC 24 V +
DC 12 V +
3
Alarm I/O
(4-Pin Terminal Block)
1
Alarm In –
Alarm connection
2
Alarm In +
3
Alarm Out –
4
Alarm Out +
4
GND
-
GND
Ground connection
5
RJ-45
-
For network and PoE connections
-
Default Button
-
Refer to the Default Button in the table
under Connectors (Indoor Only).
-
microSD Card Slot
-
Refer to the microSD Card Slot in the table
under Connectors (Indoor Only).

12
2. Camera Cabling
Follow the instructions below to complete the cable connections.
2.1 Power Connection
For power connection, refer to section Connectors (Indoor Only) for the indoor
models, and see section All in One Cable (Outdoor Only) for the outdoor models.
Alternatively, users can power the camera by PoE if a PoE switch is available.
Refer to the section below for Ethernet cable connection.
NOTE: If PoE is used, make sure to connect the camera to a PoE
switch.
2.2 Ethernet Cable Connection
To have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the camera,
and plug the other end of the cable into the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when
connecting the camera directly to the PC.
Check the status of the link indicator and the activity indicator LEDs. If the LEDs
are unlit, check the LAN connection.
A green Link Light indicates a good network connection.
An orange Activity Light flashes for network activity indication.

13
2.3 Waterproof Cable Connector
Follow the instructions below to waterproof the connectors of different types of
cables. The supported cables are as shown below.
All-in-One Cable
of the Indoor Models
All-in-One Cable
of the Outdoor Models
IP66 RJ-45 Cable
(Outdoor Models Only)
All-in-One Cable of the Indoor Models / Outdoor Models
Follow the steps below to waterproof the connectors of the All-in-One cable.
Step 1:
Connect the required devices to the
All-in-One cable and coat the joints with
silicone gel. There should be no gap between
the connectors and the cables. For the alarm
I/O connector and the power connector
(outdoor models only), make sure the side
with wires attached is also sealed with
silicone gel.
Indoor Models
Outdoor Models
For the All-in-One cable of the outdoor
models, attach the ground cable to the
ground and wrap the wires with silicone gel.
Make sure the wires are not exposed to the
air.

14
Step 2:
Seal the end of the rubber coating of the
All-in-One cable as indicated in the figure on
the right. Use enough silicone gel to fill in the
hose and wrap around each wire; otherwise,
the waterproof function cannot be
guaranteed.
IP66 RJ-45 Cable (Outdoor Models Only)
For the IP66 RJ-45 cable, use an RJ-45 IP66 plug for connection to prevent
water damage. Follow the steps below for cable connection.
Step 1:
Take out the supplied connector from the
RJ-45 IP66 plug. Loosen the thread-lock
sealing nut on the plug. Then thread the
Ethernet cable through the thread-lock
sealing nut and the plug. If the Ethernet cable
is already attached to a connector, remove it
first.
Step 2:
Carefully remove a section of rubber coating
from the end of the Ethernet cable to reveal
the wires. Insert the wires to the correct pins
of the connector. Plug the Ethernet cable to
the connector of the IP66 RJ-45 cable.
Step 3:
Fasten the RJ-45 IP66 plug to the connector
of the IP66 RJ-45 cable. Lastly, tighten the
thread-lock sealing nut to the plug.

15
3. System Requirements
To operate the IP camera via a web browser, make sure the PC is properly
connected to the network and meets the system requirements as described
below.
Items
System Requirement
Personal Computer
Minimum :
1. Intel®Core™i5-2430M @ 2.4 GHz
2. 4 GB RAM
Recommended:
1. Intel®Core™ i7-870 @ 2.93 GHz
2. 8 GB RAM
Operating System
Windows 7
Web Browser
Microsoft Internet Explorer 6.0 or later
Firefox
Chrome
Safari
Network Card
10Base-T (10 Mbps) or 100Base-TX (100 Mbps) or
1000Base-T (1000 Mbps) operation
Viewer
ActiveX control plug-in for Microsoft IE

16
4. Access Camera
For initial access to the IP camera, users can search the camera through the
installer program: Siqura Device Manager, which can be found in the “Siqura
Device Manager” folder on the supplied CD.
Accessing the Camera by the Siqura Device Manager Software
Step 1: Double-click the Siqura Device Manager setup file and follow the
instructions to install the software.
Step 2: Start Siqura Device Manager. The network is scanned and detected
devices appear in the List View pane.
If multiple network adapters exist, select the appropriate adapter to
scan the network you wish to connect to.
If necessary, use the tabs in the Tree View pane to further define the
scope of your search.
Step 3: To connect to the camera, double-click its entry in the device list.
The logon box of the camera is opened in your web browser.
Step 4: Enter the default username and password shown below to log on to
the camera.
Login ID
Password
Admin
1234
NOTE: ID and password are case sensitive.
NOTE: It is strongly advised that administrator’s password be
altered for security reasons. Refer to the Ultra High Definition
Multiple Streams IP Camera Menu Tree in the supplied CD for
further details.
Using Siqura Device Manager, it is possible to directly change the network
settings of the camera.
Assign a static IP address with Siqura Device Manager
Step 1: In Siqura Device Manager, go to the list of detected devices,
right-click the entry for the camera, click <Change Network Settings>,
and then click <Static IP >.

17
Step 2: Provide the camera with an appropriate IP address, netmask, and
gateway address for the desired network configuration, and then click
<OK> (2x).
Step 3: Wait until the network has been rescanned. In the list of found devices,
double-click the entry of the camera.
Assign a DHCP server
Step 1: Record the camera’s MAC address (see the Serial no. column in
Siqura Device Manager) for future identification.
Step 2: In Siqura Device Manager, go to the list of detected devices, right-click
the entry for the camera, click <Change Network Settings>, click
<Enable DHCP >, and then click <OK> (2x).
The network is rescanned.
Step 3: In the list of found devices, identify the camera by its MAC address
and double-click its entry.
Installing Siqura Viewer
For initial access to the camera, a client program, Siqura Viewer, will be
automatically installed to the PC when connecting to the camera.
If the web browser doesn’t allow Siqura Viewer installation, check the Internet
security settings or ActiveX controls and plug-ins settings (refer to Appendix C:
Setup Internet Security) to continue the process.
An Information Bar may be displayed, asking for permission to install the
ActiveX Control for displaying video in browser. Right-click the Information Bar
and select <Install ActiveX Control…> to allow the installation.
The download procedure of the Siqura DC Viewer software is as follows.
Step 1: In the initial screen of the installation wizard, click <Next> to start
installation.
Step 2: When the installation is complete, click <Finish>.
.

18
Once Siqura Viewer is successfully installed, the Home page of the IP camera is
shown as in the example below.
Ceiling Mount Installed Camera

19
Wall Mount Installed Camera
NOTE: For more details about the function buttons on the Home page,
please refer to the Ultra High Definition Multiple Streams IP Camera
Menu Tree in the supplied CD.

20
5. Setup Video Resolution
Users can set up the video resolution on the Video Format page of the
browser-based configuration interface.
Video Format can be found under this path: Streaming> Video Format.
NOTE: For more details about the video resolution, see the Ultra High
Definition Multiple Streams IP Camera Menu Tree document on the
supplied CD.