Sirius Satellite Radio SILT-28 Series User manual

1
SILT-28
PENDANT RANGEHOOD INSTALLATION INSTRUCTIONS
Congratulations on your purchase!
Thank you for choosing a Sirius product.
SILT-28 B EAN #9351116001810
SILT-28 C EAN #9351116001827
SILT-28 G EAN #9351116001834
SILT-28 W EAN #9351116001841
www.siriusbrand.com

2 3
DEAR CUSTOMER
The rangehood is intended for household use only. Materials used for packaging are nature friendly and may
be recycled, deposited or destroyed without any threat to the environment.
In order to recognize these features, all packing materials are marked with relevant symbols.
When you plan to replace your rangehood, deposit your old appliance with the authorized depot dealing with
used household appliances.
INSTALLATION
Instructions for use have been prepared for the user, and describe the particulars and handling of the
appliance. These instructions apply to different models from the same family of appliances, therefore you may
find information and descriptions that may not apply to your particular appliance.
INSTALLATION INSTRUCTIONS
He appliance should be connected to the power supply in accordance with the instructions from the chapter
“Electrical connections” and in line with the standing regulations and standards. The connections should be
carried out by a qualified personnel only.
FIRE HAZARD PROTECTION
Appliances are allowed to be mounted on one side next to a high kitchen cabinet, the height of which may
exceed that of the appliance. On the opposite side however, only a kitchen cabinet of equal height as the
appliance is allowed.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the
product. This appliance is marked according to the European directive
2002/96/EC on waste electrical and electronic equipment (WEEE).
The cooker surface and the lowest part of the hood
must be at a minimum distance, as shown below.
• The appliance is not intended for use by young
children without supervision. Young children
should be supervised to ensure they do not play
with the appliance.
• When performing the electrical connections on
the appliance, please make sure that the current-
tap is provided with earth connection and that
voltage values correspond to those indicated on
the label placed inside the appliance itself.
• Please disconnect the appliance from power
mains, before carrying out any cleaning or
maintenance operation. If the appliance is not
equipped with a nonseparable flexible cable and
plug, or with another device ensuring omnipolar
disconnection from the mains, with an opening
distance between the contacts of at least 3mm,
then such disconnecting devices must be
provided in the fixed installation. If the appliance
is equipped with a power cord and a plug, it shall
be placed in such a way that the plug can be
reached easily.
• The use of materials which can burst into flames
(flambé) should be avoided in close proximity of
the appliance. When frying, please pay particular
attention to fire risk due to oil and grease.
Being highly inflammable, hot oil is especially
dangerous. Do not use uncovered electric grills.
In order to avoid possible fire risk, all instructions
for grease-filter cleaning and for removing
eventual grease deposits should be strictly
followed.
• Two persons are needed for the installation of
this product. The appliance can be arranged only
for filtering performances. In its filtering version
the air and fumes conveyed by the appliance
are cleaned both by a grease filter and by an
active carbon filter, and put again into circulation.
While the lamp version (SILT28 ROLL LAMP) only
allows for hob lighting.
(Fig. 2)
600 - 700mm (induction)
650 - 750mm (gas)
WARNING
The appliance must be installed and
connected to the power supply only by a
qualified technician.
• There shall be adequate ventilation of the room when the range hood is used at the same time as
appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the
room)
• The details concerning the method and frequency of cleaning
• There is a fire risk if cleaning is not carried out in accordance with the instructions;
• Do not flambé under the range hood;
• CAUTION: Accessible parts may become hot when used with cooking appliances.
WARNING: Failure to install the screws or fixing
device in accordance with these instructions
may result in electrical hazards.

4 5
A: Mounting plate
B: Ceiling plate cover
C: Rangehood body, motor, filter, and light
• Dimensions: 480mm x 460mm
• Weight: 17.5kg
• Noise: 63 dBA
• Filters: Stainless Steel with Carbon
Re-Circulating Insert
• Airflow: 600m3/h
D: Power cable
TECHNICAL SKETCH
• Before installing the appliance read all these
instructions carefully.
• Make sure that the package is intact and all
the parts are in good condition, otherwise stop
the installation and contact the dealer. The
manufacturer is not responsible for damages
caused by material handling or product
installation.
• Extract the product from the packaging and lay it
on a suitable place on a soft material.
• Take the mounting plate out of the packaging
(Fig.1); to install the hood, position it in the
desired place of the ceiling, making sure the
centre of the plate is aligned with the centre of
the hob.
• Check that the ceiling structure is suitable to bear
the weight of the appliance (weight: 17.5kg).
Mark the holes to be drilled at the smaller
openings of the plate (Fig.2).
• Drill the holes using an 8mm diameter drill.
Fix the plate to the ceiling, by using the plastic
dowels and the screws supplied with the
appliance. Take the ceiling plate cover out of the
packaging and then introduce the power cord
and the three steel wires into the holes (fig.3).
INSTALLATION
(Fig. 1)
(Fig. 2)
(Fig. 3)
• Place the appliance close to the ceiling plate,
and then insert the steel wires into the specific
supports, as shown in Fig. 4.
• Adjust the hood desired height, paying attention
to keeping the appliance perfectly in line with the
floor by sliding the steel wire inside the support;
you will need to loosen and push the support in
order to allow the wire to slide, see Fig. 5.
• Secure the steel wires by tightening the support
and screwing it as shown in Fig.6.
• Use some clamps in order to further secure the
steel wire, see Fig. 7.
(Fig. 4)
(Fig. 5)
(Fig. 6)
(Fig. 7)
Perform the electrical connection.
Place the ceiling plate cover in such a way as to hide
the plate previously mounted, then secure it by using
the three 10mm screws provided (fig.8).
(Fig. 8)

6 7
OPERATION MODE
Standard configuration:
Standard configuration requires all rangehood radio
control systems to be provided with the same
transmission code. In the event two rangehoods are
installed in the same room or nearby, each system
may affect the operation of the another. Therefore,
the code of one radio control system must be
changed.
Generating a new transmission code:
The radio control system is provided with preset
codes. Should new codes be required, proceed as
follows: Press simultaneously buttons:
for two seconds. When LEDs are on, press buttons:
(within 5 seconds). The LEDs flashing 3 times
indicate the procedure is completed.
WARNING! This operation deletes permanently
the preset codes.
Learning the new transmission code.
Once the transmission code is changed in the radio
control unit, the electronic central unit of the cooker
hood must be made to set the new code in the
following way:
Press the main power-off button of the hood and
then restore power to the electronic control unit.
Within the next 15 seconds, press the Light Button to
synchronise the central unit with the code.
Reset of the Factory configuration:
To restore the Factory configuration, follow the
procedure described below: press simultaneously
buttons:
for 2 seconds. When LEDs light on, press buttons:
(within 5 seconds). LEDs flashing 6 times in-dicate
the procedure is completed.
WARNING! This operation deletes permanently
the preset codes.
Emergency button:
In the event that the radio control does not work, use
the emergency button to switch the appliance off.
After any necessary repairs have been performed,
reset the emergency button.
Remote control
6 channel control for rangehood remote.
• When the rangehood is first turned on, hold the
lighting button for 5 seconds.
RC001 - RADIO CONTROL
Radio control used for the remote operation of
rangehoods.
TECHNICAL DATA
• Alkaline battery powered: 12 V mod. 23 A
• Operating frequency: 433.92 Mhz
• Combinations: 32.768
• Max. consumption: 25 mA
• Operating temperature: -20 ÷ + 55 °C
• Dimensions: 120 x 45 x 15 mm.
OPERATING DESCRIPTION
The transmitter is equipped with 5 buttons for cooker
hood management, as specified below:
: Light ON/OFF command.
: Motor ON (speed level 1) / OFF command.
: Reduce speed.
: Increase speed.
: 10-minute timer.
INITIAL OPERATING CONDITION
The manufacturer supplies the radio control unit
ready to be used with codes preset in the factory.
WORKING
Any adjustments or modifications which
have not been expressly approved by the
holder of the legal conformity certificate
may invalidate the user’s rights relating to
the operation of the device.
Rev. 0 26/08/14
The products are endowed with an electronic device
which allows the automatic switching off after 4 hours
working from the last operation.
TIMING
As a result of the new EU65 “Energy label” and EU66
“ Ecodesign” regulations issued by the European
Commission, which came into force as from January
1st, 2015 , our products have been adapted to
comply with these new requirements.
All of the models complying with the energy label
requirements, are equipped with new electronics
including a timer device for suction speeds control,
when the air capacity exceeds 650m³/h.
Internal motor models, with maximum air capacity
higher than 650m³/h, are equipped with a timer
device that automatically switches the suction speed
from 4th to 3rd speed, after 5 minutes operation.
External motor models are equipped with remote
motors that , as for internal motor versions, include
a timer device that switches down the suction speed
when it exceeds 650m3/h. (See External Motors
Instructions ). Remote motors, whose air capacity
exceeds 650m³/h at both 4th and 3rd speed, will
have the following by default timer control functions:
The suction speed is automatically switched from 4th
to 2nd speed, after 6 minutes operation.
If the appliance is working at 3rd speed, it is
automatically switched to 2nd speed, after 7 minutes
operation. Operation speeds can also be changed
during operation.
The energy consumption of the appliance in standby
mode is lower than 0.5W.
The battery should be replaced every year
to guarantee the optimal range of the
transmitter.
To replace the exhausted battery, take
the plastic lid off, remove the battery and
replace it with a new one, observing the
correct battery polarities.
Used batteries should be discarded in
special collection bins.
The below product: RC001 Radio Control complies
with the specifications set out in the R&TTE Directive
99/5/EC.
WARNING
WARNING

8
MAINTENANCE
An accurate maintenance guarantees good
functioning and long-lasting performance.
*Particular care is due to the grease filter. Rotate the
lower panel of the appliance by pulling the side knob
down (see fig. 10).
• Remove the grease filter by pulling on the side
handle of the filter.
• After cleaning or replacement operations refit the
grease filter and close the lower panel previously
opened.
• The active coal filter has to be replaced in relation
to its use, at least once every six months. To
clean the appliance itself tepid water and neutral
detergent are recommended, while abrasive
products should be avoided.
• The power cord must be replaced only by
qualified person.
Fluorescent circular lamp replacement
Rotate the lower panel of the appliance by pulling the
side knob (see fig. 9-10). Remove the screws found
on the panel and open it; replace the fluorescent
lamp and then refit the panel.
Light globe: NEON LR-T5 40W 4200°K 842
(Fig. 10)
(Fig. 9)
Side knob
Red switch