Sirius Satellite Radio SILT-26 Series User manual

SILT-26
PENDANT RANGEHOOD INSTALLATION INSTRUCTIONS
Congratulations on your purchase!
Thank you for choosing a Sirius product.
SILT-26 B EAN #9351116002428
SILT-26 C EAN #9351116001308
SILT-26 G EAN #9351116001322
SILT-26 W EAN #9351116001315
www.siriusbrand.com

DEAR CUSTOMER
The rangehood is intended for household use only. Materials used for packaging are nature friendly and may
be recycled, deposited or destroyed without any threat to the environment.
In order to recognize these features, all packing materials are marked with relevant symbols.
When you plan to replace your rangehood, deposit your old appliance with the authorized depot dealing with
used household appliances.
INSTALLATION
Instructions for use have been prepared for the user, and describe the particulars and handling of the
appliance. These instructions apply to different models from the same family of appliances, therefore you may
find information and descriptions that may not apply to your particular appliance.
INSTALLATION INSTRUCTIONS
He appliance should be connected to the power supply in accordance with the instructions from the chapter
“Electrical connections” and in line with the standing regulations and standards. The connections should be
carried out by a qualified personnel only.
FIRE HAZARD PROTECTION
Appliances are allowed to be mounted on one side next to a high kitchen cabinet, the height of which may
exceed that of the appliance. On the opposite side however, only a kitchen cabinet of equal height as the
appliance is allowed.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the
product. This appliance is marked according to the European directive
2002/96/EC on waste electrical and electronic equipment (WEEE).

The cooker surface and the lowest part of the hood
must be at a minimum distance, as shown above.
• The appliance is not intended for use by young
children without supervision. Young children
should be supervised to ensure they do not play
with the appliance.
• When performing the electrical connections on
the appliance, please make sure that the current-
tap is provided with earth connection and that
voltage values correspond to those indicated on
the label placed inside the appliance itself.
• Please disconnect the appliance from power
mains, before carrying out any cleaning or
maintenance operation. If the appliance is not
equipped with a nonseparable flexible cable and
plug, or with another device ensuring omnipolar
disconnection from the mains, with an opening
distance between the contacts of at least 3mm,
then such disconnecting devices must be
provided in the fixed installation. If the appliance
is equipped with a power cord and a plug, it shall
be placed in such a way that the plug can be
reached easily.
• The appliance can be arranged only for filtering
performances. In its filtering version the air and
fumes conveyed by the appliance are cleaned
both by a grease filter and by an active carbon
filter, and put again into circulation. While the
lamp version (SILT26 LAMP) only allows for hob
lighting.
• The use of materials which can burst into flames
(flambé) should be avoided in close proximity of
the appliance. When frying, please pay particular
attention to fire risk due to oil and grease. Being
highly flammable, hot oil is especially dangerous.
Do not use uncovered electric grills. In order to
avoid possible fire risk, all instructions for grease-
filter cleaning and for removing eventual grease
deposits should be strictly followed.
• Two persons are needed for the installation of this
product.
(Fig. 2)
600 - 700mm (induction)
650 - 750mm (gas)
WARNING
The appliance must be installed and
connected to the power supply only by a
qualified technician.
TECHNICAL DATA
• Voltage rating: 230 - 240V
• 50Hz
• There shall be adequate ventilation of the room when the range hood is used at the same time as
appliancess burning gas or other fuels (not applicable to appliances that only discharge the air back into
the room)
• The details concerning the method and frequency of cleaning
• There is a fire risk if cleaning is not carried out in accordance with the instructions;
• Do not flambé under the range hood;
• CAUTION: Accessible parts may become hot when used with cooking appliances.
WARNING: Failure to install the screws or fixing
device in accordance with these instructions
may result in electrical hazards.

At the beginning make sure that the package is intact
and all the parts are unbroken, otherwise stop the
installation and contact the dealer.
The manufacturer is not responsible for
damages caused by material handling or
product installation.
Before installing the appliance read all these
instructions carefully.
WARNING: This product is made of ceramics,
for that reason it requires an appropriate and
accurate handling, as well as a professional and
accurate installation.
Extract the product from the packaging and lay it on
a suitable place, a soft material such as sponge or
fabric should be used to place the product on it.
By using the supplied drilling jig, perforate the wall
according to the four pattern indicated by the jig
itself. The center of the drilling jig should correspond
to the center of the cooktop. Insert the supplied
dowel into the holes made, tighten them, but do not
tighten until they are flush; the three screws into the
dowels corresponding to the holes with discharge
head (Fig.8 A) leaving the hole for the locking screw
empty (Fig. 9 B) because it will be added later.
EXPLODED VIEW
USES INSTALLATION
(Fig. 8)
(Fig. 9)
A: Mounting bracket
B: Ceramic plate cover
C: Rangehood body
D: Motor, light, and filter
The appliance can be arranged only for filtering
performances. In its filtering version the air and fumes
conveyed by the appliance are cleaned both by a
grease filter and by an active carbon filter, and put
again into circulation.
WARNING: Failure to install the screws or fixing
device in accordance with these instructions
may result in electrical hazards.

Place the ceramic cover over the motor components
and insert the steel cables into the three holes of the
ceramic, as shown in the figure (Fig. 1).
Put the power cable through the air outlet grill, see
Figure 2. The ceramic part must perfectly cover the
metal part named “D” in the exploded view.
Extract from the packaging the ceramic cover for the
ceiling plate (see the detail B on the exploded view),
place the cover over the hood and put the steel
cables through the three holes in the ceramic body,
the power cable should be put through the central
hole of the ceramic, see Fig.3.
Take the metal plate from the packaging and then put
the steel cables through the appropriate supports, as
shown in Fig. 4.
Adjust the height of the rangehood by scrolling the
steel cables up and down inside the support. You
need to unscrew and push the support in order to
allow the scrolling of the cable, see Fig. 5.
Check that the remaining length of steel cables from
the supports indicated in Fig.6 is the same, in order
to ensure that it will be installed perfectly parallel to
the ceiling. Tightening the appropriate support by
screwing it as shown in Fig.6, block the steel cables.
Add the clips as a further safety precaution for cable
blocking Fig. 7.
(Fig. 1)
(Fig. 4)
(Fig. 5)
(Fig. 6)
(Fig. 2)
(Fig. 3)
(Fig. 7)

Put the hood near the ceiling and hook the plate to
the screws previously installed (fig.8 A) Tighten
the three screws fixing the plate to the ceiling,
then block the hood definitively adding the security
screw, see fig.9 B. Connect the appliance to the
electric grid.
Lift up the ceramic cover until reaching the ceiling
(fig.10 ), make sure that the springs have hooked the
ceramic cover.
In case the ceramic cover of the body, is not perfectly
flat or parallel to the body, it is possible to make an
adjustment after installation. Remove the grease filter
as described in Maintenance Section, remove the
three plastic caps shown in Figure 13 A.
Using a Phillips screw head screwdriver, tighten or
loosen the three screws in order to raise or lower the
ceramic body on a specific side (fig. 14). After the
adjustment insert the rubber tips and the grease filter
again.
(Fig. 10)
(Fig. 13)
(Fig. 14)

Remote control
6 channel control for rangehood remote.
• When the rangehood is first turned on, hold the
lighting button for 5 seconds.
RC001 - RADIO CONTROL
Radio control used for the remote operation of
rangehoods.
TECHNICAL DATA
• Alkaline battery powered: 12 V mod. 23 A
• Operating frequency: 433.92 Mhz
• Combinations: 32.768
• Max. consumption: 25 mA
• Operating temperature: -20 ÷ + 55 °C
• Dimensions: 120 x 45 x 15 mm.
OPERATING DESCRIPTION
The transmitter is equipped with 5 buttons for cooker
hood management, as specified below:
: Light ON/OFF command.
: Motor ON (speed level 1) / OFF command.
: Reduce speed.
: Increase speed.
: 10-minute timer.
INITIAL OPERATING CONDITION
The manufacturer supplies the radio control unit
ready to be used with codes preset in the factory.
WORKING OPERATION MODE
Standard configuration:
Standard configuration requires all rangehood radio
control systems to be provided with the same
transmission code. In the event two rangehoods are
installed in the same room or nearby, each system
may affect the operation of the another. Therefore,
the code of one radio control system must be
changed.
Generating a new transmission code:
The radio control system is provided with preset
codes. Should new codes be required, proceed as
follows: Press simultaneously buttons:
for two seconds. When LEDs are on, press buttons:
(within 5 seconds). The LEDs flashing 3 times
indicate the procedure is completed.
WARNING! This operation deletes permanently
the preset codes.
Learning the new transmission code.
Once the transmission code is changed in the radio
control unit, the electronic central unit of the cooker
hood must be made to set the new code in the
following way:
Press the main power-off button of the hood and
then restore power to the electronic control unit.
Within the next 15 seconds, press the Light Button to
synchronise the central unit with the code.
Reset of the Factory configuration:
To restore the Factory configuration, follow the
procedure described below: press simultaneously
buttons:
for 2 seconds. When LEDs light on, press buttons:
(within 5 seconds). LEDs flashing 6 times in-dicate
the procedure is completed.
WARNING! This operation deletes permanently
the preset codes.
Emergency button:
In the event that the radio control does not work, use
the emergency button to switch the appliance off.
After any necessary repairs have been performed,
reset the emergency button.

TIMING
As a result of the new EU65 “Energy label” and EU66
“ Ecodesign” regulations issued by the European
Commission, which came into force as from January
1st, 2015 , our products have been adapted to
comply with these new requirements.
All of the models complying with the energy label
requirements, are equipped with new electronics
including a timer device for suction speeds control,
when the air capacity exceeds 650m³/h.
Internal motor models, with maximum air capacity
higher than 650m³/h, are equipped with a timer
device that automatically switches the suction speed
from 4th to 3rd speed, after 5 minutes operation.
External motor models are equipped with remote
motors that , as for internal motor versions, include
a timer device that switches down the suction speed
when it exceeds 650m3/h. (See External Motors
Instructions ). Remote motors, whose air capacity
exceeds 650m³/h at both 4th and 3rd speed, will
have the following by default timer control functions:
The suction speed is automatically switched from 4th
to 2nd speed, after 6 minutes operation.
If the appliance is working at 3rd speed, it is
automatically switched to 2nd speed, after 7 minutes
operation. Operation speeds can also be changed
during operation.
The energy consumption of the appliance in standby
mode is lower than 0.5W.
MAINTENANCE
An accurate maintenance guarantees good
functioning and longlasting performance. *Particular
care is due to the grease filter The grease filter is
fixed through magnets, therefore it is sufficient to
insert a hand tool or the tip of a knife in the dedicated
opening and push upwards in order to pull the filter
out of its place. See Fig. 12. In order to remove the
filter from the hood, unhook the two security cables
opening their snap-hooks, The active coal filter has
to be removed after the extraction of the grease filter
by pushing its special plastic handle. The grease filter
can be cleaned by hand-washing or in dishwashers.
The active coal filter has to be replaced in relation to
its use, at least once every six months. To clean the
appliance itself tepid wa-ter and neutral detergent are
recommended, while abrasive products should be
avoided.
The power cord must be replaced only by qualified
person.
The LED lamps must be replaced only by qualified
person.
(Fig. 14)

WORKING