Sirona c8+ turn User manual

kÉï=~ë=çÑW MVKOMMV
båÖäáëÜ
`UH
fåëí~ää~íáçå=oÉèìáêÉãÉåíë= =

MVKOMMV
General information Sirona Dental Systems GmbH
Installation Requirements
60 28 000 D3417
2D3417.021.04.09.02
Changes since the last version 12.2007:
Chapter or section, page
1.4 Underfloor installation of SIVISION connections .. 11
2.1 C8+1:20 ................................................................ 16
2.2 C8+Cart 1:20 ........................................................ 21
2.3 C8+Rear delivery 1:20 ......................................... 23
2.4 C8+Side delivery 1:20 .......................................... 25
2.6 C8+Turn 1:20 ........................................................ 28
2.7 C8+Turn Cart 1:20 ................................................ 35
2.8 C8+Turn Rear delivery 1:20 ................................. 37
3.1 Accessories .......................................................... 50
About this document
This document describes the installation requirements for
the C8+dental treatment centers.
Their subsequent installation is described in the Installation
Instructions:
• REF 59 42 912 (C8+)
• REF 59 78 197 (C8+Tur n)
• REF 59 88 428 (C8+Solo, C8+Solo Cart/Cabinet,
C8+Cart Stand-Alone, C8+Cabinet Stand-Alone)
Besides you need the drilling template, for secure fastening
of the treatment center to the floor:
• REF 59 66 911 (C8+, C8+Tur n)
• 59 88 824 (C8+Solo, C8+Solo Cart/Cabinet, C8+Cart
Stand-Alone, C8+Cabinet Stand-Alone)
General information

Sirona Dental Systems GmbH List of Contents
Installation Requirements C8+
60 28 000 D3417
D3417.021.04.09.02 3
båÖäáëÜ
1Preparations.......................................................................................................................... 5
1.1 Safety........................................................................................................... 6
1.2 Media quality................................................................................................ 7
1.3 Supply lines in the termination panel........................................................... 8
1.4 Underfloor installation of SIVISION connections ......................................... 11
1.5 Mounting plates for C8+(not for C8+Turn)................................................... 12
1.6 Demonstration plate for C8+Turn................................................................ 13
1.7 C8+Dentist element Rear delivery / Side delivery....................................... 14
2Dimensions, technical data ................................................................................................. 15
2.1 C8+1:20 ...................................................................................................... 16
2.2 C8+Cart 1:20............................................................................................... 21
2.3 C8+Rear delivery 1:20 ................................................................................ 23
2.4 C8+Side delivery 1:20................................................................................. 25
2.5 C8+: Technical data ..................................................................................... 27
2.6 C8+Turn 1:20 .............................................................................................. 28
2.7 C8+Turn Cart 1:20 ...................................................................................... 35
2.8 C8+Turn Rear delivery 1:20........................................................................ 37
2.9 C8+ Turn: Technical data............................................................................. 39
2.10 C8+Solo 1:20 ............................................................................................. 40
2.11 C8+Solo Cart 1:20 ..................................................................................... 41
2.12 C8+Solo Rear delivery 1:20 ....................................................................... 42
2.13 C8+Solo Side delivery 1:20........................................................................ 43
2.14 C8+Cart Stand-Alone 1:20......................................................................... 44
2.15 C8+Rear delivery Stand-Alone (only for USA) 1:20................................... 45
2.16 C8+Side delivery Stand-Alone (only for USA) 1:20 ................................... 46
2.17 C8+Solo, C8+Solo Cart/Rear delivery/Side delivery,
C8+Cart/Rear delivery/Side delivery Stand-Alone: Technical data ............ 47
3Electromagnetic compatibility ............................................................................................ 49
3.1 Accessories ................................................................................................. 50
3.2 Electromagnetic emission............................................................................ 51
3.3 Immunity to interference .............................................................................. 52
3.4 Working clearances ..................................................................................... 54
List of Contents

C8+
60 28 000 D3417
D3417.021.04.09.02 5
båÖäáëÜ
1 Preparations
1.1 Safety .................................................................................................................................... 6
1.2 Media quality ......................................................................................................................... 7
1.3 Supply lines in the termination panel ..................................................................................... 8
1.4 Underfloor installation of SIVISION connections ................................................................... 11
1.5 Mounting plates for C8+(not for C8+Turn) ............................................................................ 12
1.6 Demonstration plate for C8+Turn ......................................................................................... 13
1.7 C8+Dentist element Rear delivery / Side delivery ................................................................ 14

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+
60 28 000 D3417
6D3417.021.04.09.02
båÖäáëÜ
ATTENTION
It is essential that you comply with the warning and safety
information contained in the Installation Requirements.
All such information is highlighted by the captions NOTE,
CAUTION, and WARNING.
ATTENTION
For reasons of product safety, only original Sirona accesso-
ries approved for this product, or accessories from third par-
ties approved by Sirona, may be used. The user is respon-
sible for dangers resulting from the use of non-approved
accessories.
If any devices not approved by Sirona are connected, they
must comply with the applicable standards, e.g.:
• IEC 60950 for information technology equipment and
• IEC IEC 60601-1 for medical electrical equipment
In case of doubt, contact the manufacturer of the system
components.
ATTENTION
Any person who assembles or modifies a medical electrical
system complying with the standard IEC 60 601-1-1 (safety
requirements for medical electrical equipment) by combin-
ing it with other equipment (e.g. when connecting a PC) is
responsible for ensuring that the requirements of this regu-
lation are met to their full extent for the safety of the patients,
the operators and the environment.
ATTENTION
The floor must be flat and level (DIN 18 202). A mounting
plate must be used for uneven floors (see Section 1.5,
"Mounting plates for C8+(not for C8+Turn)" on page 12).
ATTENTION
The floor must have a minimum loading capacity of 0.5N/
cm².
ATTENTION
Interference of electromedical devices caused by radio tele-
phones:
To ensure the operational readiness of electromedical de-
vices, the use of mobile radio telephones in the practice or
hospital area is prohibited.
ATTENTION
Electromagnetic compatibility: The unit should not be op-
erated in the immediate vicinity of other devices. If this
proves to be unavoidable, the unit should be monitored to
ensure that it is used properly.
1.1 Safety

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+
60 28 000 D3417
D3417.021.04.09.02 7
båÖäáëÜ
,
Water quality
Lime deposits and corrosion residues in tap water can lead
to the following malfunctions:
• Premature clogging of the filters in the unit
• Rapid clogging of the fine water paths and jets in the
treatment instruments
For these reasons, the following points must be observed:
• If the water hardness exceeds 12° dH (=2.15mmol), in-
stall a water softener.
• Set dilution hardness to 8° dH (1.43mmol).
• Install a conventional fine filter.
Fineness: >80µm (0.08mm).
• Installation must be performed in compliance with the
recommendations of the national installation require-
ments (e.g. EN1717/DIN 1988).
• The water quality must comply with the national re-
quirements for drinking water.
• The connection must be made to cold water.
Air quality
Oil-free, dry and hygienically perfect air is required for driv-
ing the highspeed handpiece, for cooling the burr drives
and for the cooling spray.
Suction pipe
Install steam trap K.
With a vacuum of pu >0.18 bar back pressure, the treat-
ment center must be retrofitted with the “Vacuum limiter”
retrofit kit (Order No.: 59 68 826).
1.2 Media quality
N
>80 µm
Air
Suction machine
oil-free
Cold water
Dilution hardness
(drinking water quality)

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+
60 28 000 D3417
8D3417.021.04.09.02
båÖäáëÜ
1.3 Supply lines in the termination panel
5
3
6
6
67
Center base plate
opening to floor
1
2
4
9
1 3/8“
min.
500mm
20"
7, 6
max.
60mm
2 3/8"
3 4 5
max.
5mm
3/16"
max.
5mm
3/16"
3/8"
12
10 x 1mm 10 x 1mm
3/8
”
x 1/32“
3/8
”
x 1/32“
1 3/8“
Foot end
36.5mm
50mm
36.5mm

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+
60 28 000 D3417
D3417.021.04.09.02 9
båÖäáëÜ
• Observe the national regulations for electrical installa-
tions (e.g. VDE 0100, VDE 0100, Part 710).
• Observe the national regulations for water supply in-
stallations (e.g. EN 1717, DIN 1988) and sewage instal-
lations (e.g. EN 12056-1).
• For the suction pipe, observe the instructions in the
Suction Machine Installation Instructions.
• For fastening the pipe ends in the installation field, we
recommend using an installation template. They can
be ordered from Sirona under REF 33 15 830.
If necessary, you can also prepare the template your-
self based on the above sketch (not true to scale!).
Supply lines in the termination panel
Table 1: Supply lines
Item Description
1Water inlet pipe 10x1mm,
corner valve outlet 3/8"
2Compressed air inlet pipe 10x1mm, corner
valve outlet 3/8"
3Suction pipe DN40 HT-PP DIN 19560 (polypro-
pylene, inner diameter 36.5mm!)
4Water drain DN40 HT-PP DIN 19560 (polypro-
pylene, inner diameter 36.5mm!)
5Installation pipe, DN40 HT-PP DIN 19560
(polypropylene, 40mm!)
6Suction machine control cable ( )and call
cables ( ) 3x1.5mm2
7Power cable 3x1.5mm2
Fuse: 16A slow-blow
Recommended: Type B automatic circuit breaker
8 not applicable
9 Installation pipe (or corresponding flat duct) for
additional requirement e.g. practice network
connecting cable
,

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+
60 28 000 D3417
10 D3417.021.04.09.02
båÖäáëÜ
Supply above the floor, "above-floor installation"
The supply pipe ends, corner valves and cables must be
routed as shown above.
The retrofit kit for above-floor installation (33 17 265) is
required for installation.
ATTENTION
For cleaning, rinse the air and water pipes thoroughly (metal
chips!).
Supply through the floor, "underfloor installation"
1. The top edges of the corner valves for air and water
must not protrude more than 60mm above the upper
surface of the finished floor.
2. The suction and drain pipes must be flush with the up-
per surface of the floor (a deviation of +5mm is permis-
sible).
Internal diameter for both pipes: 36,5mm.
3. The electrical cables must protrude at least 500mm.
Supply lines in the termination panel
>500mm
<5mm
<60mm
>20“
3/8“
<3/16“
<2 3/8“
Ø 36,5 mm
10x1 mm
3/8” x 1/32”
DN 40
>5
00mm
200mm
250mm
> 20’’
8’’
10’’
Ø 36,6mm
3/8“
20
Ø 36,5 mm
Installation template

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+
60 28 000 D3417
D3417.021.04.09.02 11
båÖäáëÜ
Important information for the installer
Depending on the prevailing local conditions, the existing
cable set can be installed in the cable duct of an underfloor
installation by an installer prior to the installation of the den-
tal treatment center. In this case, please observe the follow-
ing:
Proceed with extreme care when running the cables. Par-
ticularly cables L15 and L38 are very sensitive, and must
never be kinked or twisted. The cables must not overlap or
cross one another.
RS232 (L37) and the XGA cable (L38) are not yet cut to
length and terminated on the PC side. It would be impossi-
ble to pull the cables through when installing them under
floor level if a sub D connector were already connected.
These cables should always be pulled.
Free length A of cables at the treatment center end:
Length A = 600mm
If S video cable L15 is equipped with both a female and a
male connector, make sure that the female connector
(socket) points to the connection box of the treatment
center.
1. Bend the wire at the front end of cables L37 and L38 to
form a hook.
2. Pull cables L15, L37 and L38 as well as the audio ca-
ble and protective ground wire from the treatment cent-
er through the cable duct to the location of the SIVI-
SION PC.
Save the accessory parts for final installation!
1.4 Underfloor installation of SIVISION connections
2.
1.
A
L15, L37, L38, Audio
protective ground wire
SIVISION

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+
60 28 000 D3417
12 D3417.021.04.09.02
båÖäáëÜ
1.5 Mounting plates for C8+(not for C8+Turn)
Chair plate
Demo plate
REF 58 26 511
REF 47 08 074
For especially uneven floor conditions,
a steel chair plate is available to compensate for the
irregularities of the floor (REF 58 26 511).
For floors which do not permit permanent connection of the unit (e.g. demo
operation at a fair), installation on a steel demo plate is possible
(REF 47 08 074).

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+
60 28 000 D3417
D3417.021.04.09.02 13
båÖäáëÜ
1.6 Demonstration plate for C8+Turn
Demonstration plate
For floors which do not permit permanent con-
nection of the unit (e.g. demo operation at a fair),
installation on a steel demo plate is possible
(REF 59 46 269).
REF 59 46 269
C8+Turn

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+
60 28 000 D3417
14 D3417.021.04.09.02
båÖäáëÜ
1.7 C8+Dentist element Rear delivery / Side delivery
ATTENTION
In order to ensure mechanical stability, in-
stall the dentist element only on cabinets ap-
proved by Sirona.
Never place any objects on the dentist ele-
ment.
ATTENTION
In order to ensure mechanical stability, in-
stall the dentist element only on cabinets ap-
proved by Sirona.
max.
2 kg
4.4 lbs

C8+
60 28 000 D3417
D3417.021.04.09.02 15
2 Dimensions, technical data
2.1 C8+1:20 ............................................................................................................................... 16
2.2 C8+Cart 1:20........................................................................................................................ 21
2.3 C8+Rear delivery 1:20 ......................................................................................................... 23
2.4 C8+Side delivery 1:20.......................................................................................................... 25
2.5 C8+: Technical data .............................................................................................................. 27
2.6 C8+Turn 1:20 ....................................................................................................................... 28
2.7 C8+Turn Cart 1:20 ............................................................................................................... 35
2.8 C8+Turn Rear delivery 1:20................................................................................................. 37
2.9 C8+ Turn: Technical data...................................................................................................... 39
2.10 C8+Solo 1:20 ....................................................................................................................... 40
2.11 C8+Solo Cart 1:20 ............................................................................................................... 41
2.12 C8+Solo Rear delivery 1:20 ................................................................................................. 42
2.13 C8+Solo Side delivery 1:20.................................................................................................. 43
2.14 C8+Cart Stand-Alone 1:20................................................................................................... 44
2.15 C8+Rear delivery Stand-Alone (only for USA) 1:20............................................................. 45
2.16 C8+Side delivery Stand-Alone (only for USA) 1:20 ............................................................. 46
2.17 C8+Solo, C8+Solo Cart/Rear delivery/Side delivery, C8+Cart/Rear delivery/Side
delivery Stand-Alone: Technical data .................................................................................. 47

2 Dimensions, technical data Sirona Dental Systems GmbH
2.1 C8+1:20 Installation Requirements C8+
60 28 000 D3417
16 D3417.021.04.09.02
Recommended distances from cabinet or wall.
2.1 C8+1:20
1700
67”
1300
51 3/16”
2500
98 7/16”
250
9 7/8”
!
!
Hazard warning:
The here mounted lamp and the dentist
element have a wider swivelling range
than the distances indicated!
Center floor opening
250
9 7/8”

Sirona Dental Systems GmbH 2 Dimensions, technical data
Installation Requirements C8+2.1 C8+1:20
60 28 000 D3417
D3417.021.04.09.02 17
With long support arm for the dentist element
C8+1:20
* max. 755 29 3/4”
min. 395 15 1/2"
1212
47 3/4”
Standard upholstery
*max.: backrest and chair in highest position
min.: backrest and chair in lowest position
45
1 3/4”
90
3 1/2”
45°
65°
10°
max. 1230 48 3/8”
min. 760 29 7/8”
1950
76 3/4”
1875
73 3/4”
Height of lamp with
SIVISION on swivel
arm or lamp support
tube
Height of lamp without
SIVISION or with
SIVISION on tray
SIROLUXLEDview

2 Dimensions, technical data Sirona Dental Systems GmbH
2.1 C8+1:20 Installation Requirements C8+
60 28 000 D3417
18 D3417.021.04.09.02
C8+1:20
1540
60 5/8”
860
33 7/8”
1210
47 1/2”
310
12 1/4”
max. 380 +15
15“ +5/8”
2070 +50***
81 1/2” +2“ ***
45
1 3/4”
78
3”
459
18”
430 +15
17“ +5/8”
180
7”
90°
90° 90°
60°
750
29 1/2”
770
30 3/8”
250
9 7/8”
*** according to chair height

Sirona Dental Systems GmbH 2 Dimensions, technical data
Installation Requirements C8+2.1 C8+1:20
60 28 000 D3417
D3417.021.04.09.02 19
With short support arm for the dentist element
C8+1:20
* max. 755 29 3/4”
min. 395 15 1/2"
1212
47 3/4”
Standard upholstery
*max.: backrest and chair in highest position
min.: backrest and chair in lowest position
45
1 3/4”
90
3 1/2”
45°
65°
10°
max. 1440 56 3/4”
min. 970 38 1/8”
1950
76 3/4”
1875
73 3/4”
Height of lamp with
SIVISION on swivel
arm or lamp support
tube
Height of lamp without
SIVISION or with
SIVISION on tray
SIROLUXLEDview

2 Dimensions, technical data Sirona Dental Systems GmbH
2.1 C8+1:20 Installation Requirements C8+
60 28 000 D3417
20 D3417.021.04.09.02
C8+1:20
*** according to chair height
max. 380 +15
15“ +5/8”
1170
46”
860
33 7/8”
1210
47 1/2”
310
12 1/4”
150°
140°
2070 +50***
81 1/2” +2“ ***
45
1 3/4”
459
18”
430 +15
17“ +5/8”
180
7”
90°
90° 90°
60°
750
29 1/2”
770
30 3/8”
250
9 7/8”