Sirona teneo User manual

fåëí~ää~íáçå=oÉèìáêÉãÉåíë
MUKOMNP
qbkbl
kÉï=~ë=çÑW==
båÖäáëÜ
Cover page

61 93 739 D3509
D3509.021.01.12.02 08.2013 3
Sirona Dental Systems GmbH
Installation Requirements TENEO
båÖäáëÜ
Table of contents
1General information.................................................................................................. 5
1.1 Notes on the installation prerequisites .......................................................... 5
1.2 Identification of the danger levels.................................................................. 5
2Safety information .................................................................................................... 6
2.1 Installation by qualified personnel ................................................................. 6
2.2 Cellular phones ............................................................................................. 6
2.3 Modifications and extensions of the system.................................................. 6
2.4 Power connection.......................................................................................... 7
3On-site installation.................................................................................................... 8
3.1 Substrate, floor.............................................................................................. 8
3.1.1 Pressure load..................................................................................... 8
3.2 Connection to the public drinking water system............................................ 8
3.3 Media quality ................................................................................................. 9
3.4 Above-floor installation of supply lines .......................................................... 12
3.5 Underfloor installation of supply lines............................................................ 13
3.5.1 Installation template ........................................................................... 13
3.5.2 Installation of the supply line in the termination panel........................ 15
3.6 Cleaning the air and water pipes................................................................... 16
3.7 Underfloor installation of the PC connections ............................................... 17
4Dimensions, technical data ...................................................................................... 19
4.1 Scale 1:20 ..................................................................................................... 19
4.1.1 Dimensions of the treatment room..................................................... 19
4.1.2 Side view............................................................................................ 20
4.1.3 Top view............................................................................................. 21
4.1.4 Top view with options......................................................................... 22
4.2 Mounting plates............................................................................................. 23
4.3 Information on planning for the practice........................................................ 25
4.4 Technical data............................................................................................... 26
4.5 Standards/Approvals..................................................................................... 28

61 93 739 D3509
4D3509.021.01.12.02 08.2013
Sirona Dental Systems GmbH
Installation Requirements TENEO
5Electromagnetic compatibility................................................................................... 30
5.1 Accessories................................................................................................... 30
5.2 Electromagnetic emission ............................................................................. 31
5.3 Interference immunity.................................................................................... 32
5.4 Working clearances....................................................................................... 34
5.5 Foot control wireless interface ...................................................................... 35
6Checklist................................................................................................................... 36
6.1 Installation site .............................................................................................. 36
6.2 Construction requirements ............................................................................ 37
6.3 IT hardware ................................................................................................... 38
6.4 Network ......................................................................................................... 39
6.5 Data processing ............................................................................................ 40

61 93 739 D3509
D3509.021.01.12.02 08.2013 5
Sirona Dental Systems GmbH 1General information
Installation Requirements TENEO 1.1 Notes on the installation prerequisites
båÖäáëÜ
1General information
General information
1.1 Notes on the installation prerequisites
Notes on t he installation prerequisite s
TENEO product
This document describes the installation prerequisites for the TENEO
treatment center.
It contains the following information:
● Required information for practice planning.
● Information for the installer, such as how to implement the
connections for air, water, waste water, suction air and the power
supply.
● Information on the cabling of the PCs to be connected.
● Information about electromagnetic compatibility and the prerequisites
for setting up the treatment center.
● A checklist to ensure that all installation requirements have been
fulfilled.
TENEO installation instructions
The subsequent installation of the treatment center is described in the
installation instructions (REF 61 93 689).
You will also need the drilling template (REF 61 94 000) for the safe and
secure attachment of the treatment center to the floor.
1.2 Identification of the danger levels
Identification of the danger levels
To prevent personal injury and material damage, please observe the
warning and safety information provided in this document. Such
information is highlighted as follows:
Tip: Information on making work easier.
DANGER
An imminent danger that could result in serious bodily injury or death.
WARNING
A possibly dangerous situation that could result in serious bodily injury
or death.
CAUTION
A possibly dangerous situation that could result in slight bodily injury.
NOTICE
A possibly harmful situation which could lead to damage of the product
or an object in its environment.
IMPORTANT
Application instructions and other important information.

61 93 739 D3509
6D3509.021.01.12.02 08.2013
2 Safety information Sirona Dental Systems GmbH
2.1 Installation by qualified personnel Installation Requirements TENEO
2Safety information
Safety information
2.1 Installation by qualified personnel
Installation by qualified personnel
Installation by qualified personnel
The installation of the supply connections must be carried out only by
qualified personnel.
Electrical and water supply installations; reference for INST suction machines
2.2 Cellular phones
Cellular p hones
Mobile RF communications equipment may interfere with medical
electrical equipment. Therefore, the use of mobile wireless phones in
medical office or hospital environments must be prohibited.
2.3 Modifications and extensions of the system
Modifications and ex tensions of the sy stem
Modifications to this system which might affect the safety of the system
owner, patients or other persons are prohibited by law.
For reasons of product safety, this product may be operated only with
original Sirona accessories or third-party accessories expressly approved
by Sirona. The user assumes the risk of using non-approved accessories.
If any devices not approved by Sirona are connected, they must comply
with the applicable standards, e.g.:
● IEC 60950 for information technology equipment (e.g. PC) and
● IEC 60601-1 for medical electrical equipment.
The treatment center monitor must fulfill the requirements of the
IEC 60950 standard.
The loudspeaker port of the monitor may be connected only to a device
that complies with IEC 60950 (e.g. a PC) or
IEC 60601-1. Under no circumstances may it be connected to a stereo
system, or similar, for example.
If a system is created during the installation process, the requirements of
IEC 60601-1, 3rd edition, must be fulfilled. The system author assumes
responsibility for conformity of the system with 93/42/EEC Directive.
WARNING
Professional installation
Comply with the national regulations for electrical installations (e.g.
VDE 0100, VDE 0100, Part 710).
Comply with the national regulations for water supply installations (e.g.
EN 1717, DIN 1988) and sewage installations (e.g. EN 12056-1).
For suction lines: adhere to the specifications in the installation
instructions for "Suction machines".

61 93 739 D3509
D3509.021.01.12.02 08.2013 7
Sirona Dental Systems GmbH 2Safety information
Installation Requirements TENEO 2.4 Power connection
båÖäáëÜ
2.4 Power connection
Power connection
WARNING
Shock hazard
It is essential that you switch off the power supply PRIOR to beginning
the installation. There is a risk of electric shock. People can be injured
or electrical components of the unit destroyed.

61 93 739 D3509
8D3509.021.01.12.02 08.2013
3 On-site installation Sirona Dental Systems GmbH
3.1 Substrate, floor Installation Requirements TENEO
3On-site installation
On-site installation
3.1 Substrate, floor
Substrate, floo r
Unevenness The floor must be level and horizontal in accordance with DIN 18 202.
The shimming plates (A) in the accessory pack can be used for
evennesses of up to 2 mm.
If the unevenness of the floor exceeds 2 mm over the total length of the
chair base (approx. 1300mm), the steel adapter plate (B) must be used;
see Mounting plates [ → 23].
3.1.1 Pressure load
Pressure load
Load capacity:
The minimum load-bearing capacity of the floor must be 0.5 N/cm2
(corresponds to around 500 kg/m2).
3.2 Connection to the public drinking water system
Connecti on to the pu blic drinking water system
The treatment center meets the requirements of the DVGW (German Gas
and Water Association).
It is intrinsically safe in accordance with worksheet W540 and therefore
fulfills the requirements of W270 and KTW (plastics in waterways). The
German Gas and Water Association (DVGW) approval can be viewed on
a label next to the rating plate.
Please always adhere to the national requirements with regard to
connecting treatment centers to the public drinking water system.
0,5
N/cm20,7
lbs/sq in.

61 93 739 D3509
D3509.021.01.12.02 08.2013 9
Sirona Dental Systems GmbH 3On-site installation
Installation Requirements TENEO 3.3 Media quality
båÖäáëÜ
3.3 Media quality
Media quality
Water quality
Kaltwasser (Trinkwasserqualität)
Cold water (drinking water quality)
Eau froide (eau potable)
Agua corriente (agua potable)
1 bar = 14.5 PSI
p 0,18 bar
u<
> 500 l/min
Wasserhärte
Dureté de l’ eau
Water hardness
Dureza del agua
1,4 mmol l 8° dH/(= )
> 80 m = 0,08 mmµ
> 2,5 l/min
> 2,5 bar
< 6,0 bar
< 7,5 bar
> 50 l/min
> 5,5 bar
K
Suction machine
Compressed air (oil-free)
The compressor must draw in hygienically faultless air.
Cold water (drinking water quality)
K Steam trap

61 93 739 D3509
10 D3509.021.01.12.02 08.2013
3 On-site installation Sirona Dental Systems GmbH
3.3 Media quality Installation Requirements TENEO
Water quality
Lime deposits and corrosion residues in tap water can lead to the
following malfunctions:
● Premature clogging of the filters in the unit
● Rapid clogging of the fine water paths and jets in the treatment
instruments
For these reasons, the following points must be observed:
● Permitted water pressure: 2.5bar (36.25psi) to 6bar (87psi)
● Permitted minimum flow volume: 3l/min
● For water hardness (total hardness) of 2.2 mmol/l (= 12° dH ), install
water softeners.
Set the blend hardness to 1.4 mmol/l (= 8° dH).
● Install a conventional fine filter; fineness: > 80 µm (0.08 mm).
● Installation must be performed in compliance with the
recommendations of the national installation requirements (e.g. EN
1717/DIN 1988).
● The water quality must comply with the national requirements for
drinking water.
● The connection must be made to cold water.
● When laying the water pipe to the treatment center, comply with the
following instructions to reduce the quantity of micro-organisms in the
feed pipe:
– Avoid long stub lines to the treatment center.
– Carry out the installation so that, where possible, other main
consumers (such as the sink) are fed from the same line
downstream of the treatment center connection.
– Avoid laying the supply line parallel to hot water pipes.
● Before installation, an acceptable microbiological water quality
(drinking water) must be ensured and documented in the form of a
colony count.
● Sampling and the colony count must be performed by a competent
laboratory.
● The colony count must fulfill the national regulations for drinking
water and must not exceed 500 CFU/ml under any circumstances
(CFU: colony forming units).
● In the event of an increased colony count, the indoor installation must
be checked and the cause of contamination eliminated. Alternatively,
a stand-alone water supply can also be installed.
● Observe EN 1717 for the protection of public drinking water.
The treatment center fulfills the requirements of EN 1717 and that of
the DVGW (the German Technical and Scientific Association for Gas
and Water). It is intrinsically safe in accordance with worksheet
W540. It can be connected directly to the public drinking water
system.

61 93 739 D3509
D3509.021.01.12.02 08.2013 11
Sirona Dental Systems GmbH 3On-site installation
Installation Requirements TENEO 3.3 Media quality
båÖäáëÜ
Air quality
Air quality
The air for driving the turbines, for cooling the drives and for the cooling
spray must be free from oil, dry and hygienically faultless.
Install a steam trap K.
● Permissible air pressure: 5.5bar (80psi to 7.5bar (109psi)
● Permissible minimum flow rate: 50l/min
Suction pipe
Suction pipe
With a vacuum of pu > 0.18 bar without flow, the treatment center must
be retrofitted with the "Vacuum limiter" retrofit kit (REF 59 68 826).
● Minimum suction power: 500l/min
● Maximum vacuum: 0.18bar (2.6psi)

61 93 739 D3509
12 D3509.021.01.12.02 08.2013
3 On-site installation Sirona Dental Systems GmbH
3.4 Above-floor installation of supply lines Installation Requirements TENEO
3.4 Above-floor installation of supply lines
Above-floor installation of supply lines
Alternative line feed Above and underfloor installation
The supply lines can be installed above the floor (above-floor installation)
or through the floor (underfloor installation).
For the installation of the supply lines through the floor, see "Underfloor
installation of supply lines" [ → 13].
✔The retrofit kit "Above-floor installation" (Order No.: 62 05 004) is
required for the connection.
➢Lay the ends of the supply pipes, corner valves and lines as shown in
the illustration.
ªThe supply lines are laid.
Suction line
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter 36.5 mm)
Compressed air supply
Pipe 10x1 mm, corner valve outlet 3/8"
Water supply
Pipe 10x1 mm, corner valve outlet 3/8"
Water drainage
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter 36.5 mm)
Power supply
3x1.5 mm2
Circuit breaker: for 230 VAC: 16 A slow-blow
for 100-115 VAC: 20 A slow-blow
Recommended: Type B automatic circuit breaker
Cu 10x1 mm
DN 40
200 mm
250 mm
8’’
10’’
> 500 mm
>20’’
Ø 36,6mm
3/8“

61 93 739 D3509
D3509.021.01.12.02 08.2013 13
Sirona Dental Systems GmbH 3On-site installation
Installation Requirements TENEO 3.5 Underfloor installation of supply lines
båÖäáëÜ
3.5 Underfloor installation of supply lines
Underfloor installati on of supply lines
3.5.1 Installation template
Installation tem plate
We recommend that you order the installation template (REF 33 15 830)
from Sirona for laying the pipe ends in the installation field. If necessary,
you can also prepare the template yourself based on the diagram below.

61 93 739 D3509
14 D3509.021.01.12.02 08.2013
3 On-site installation Sirona Dental Systems GmbH
3.5 Underfloor installation of supply lines Installation Requirements TENEO
1 Water supply
Pipe 10x1 mm, corner valve outlet 3/8"
2 Compressed air supply
Pipe 10x1 mm, corner valve outlet 3/8"
3 Suction line
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter 36.5 mm)
4 Water drainage
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter 36.5 mm)
5 Installation pipe
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter 40 mm)
6 Control cable to relays for the
suction machine ( ),
call cable (),
Special function (#)
3 x 1.5 mm2 (quality as in the power cable)
7 Power supply
3x1.5 mm2
Circuit breaker: for 230 VAC: 16 A slow-blow
for 100-115 VAC: 20 A slow-blow
Recommended: Type B automatic circuit breaker
8 not connected
9 Installation pipe, inner diameter 50 mm
(or corresponding flat conduit) for the PC connection

61 93 739 D3509
D3509.021.01.12.02 08.2013 15
Sirona Dental Systems GmbH 3On-site installation
Installation Requirements TENEO 3.5 Underfloor installation of supply lines
båÖäáëÜ
3.5.2 Installation of the supply line in the termination panel
Installation o f the supply lin e in the termination panel
✔An installation template is available or was prepared.
1. Check the position of the supply lines against the installation template
as per the practice blueprint. Ensure that sufficient space is provided
between the lines and the walls; see "Scale 1:20" [ → 19]. The center
of the hole in the floor must be 269 mm (10 5/8") from the foot of the
treatment center.
2. Lay the ends of the supply pipes, corner valves and lines as shown in
the illustrations.
ªThe top edge of the corner valves for air and water must not project
more than 60 mm from the top edge of the floor.
ªThe suction and drainage pipes must be flush with the top edge of the
floor (a deviation of +5 mm is permissible). The inner diameter of both
pipes is 36.5 mm.
ªThe electric lines must project by at least 500 mm.
ªThe supply lines are laid.
3/8“
<5mm
< 60mm
< 3/16“
< 2 3/8“
Ø 36,5 mm
Ø 36,5 mm
>500mm
>20“

61 93 739 D3509
16 D3509.021.01.12.02 08.2013
3 On-site installation Sirona Dental Systems GmbH
3.6 Cleaning the air and water pipes Installation Requirements TENEO
3.6 Cleaning the air and water pipes
Cleaning the air and water pipes
Flushing the air and water pipes
NOTICE
Chips and other foreign materials could be flushed and/or blown into the
treatment center.
Metal chips can cause malfunctions of the pneumatic components. The
filters become clogged with foreign materials.
➢During installation, ensure that no chips or other foreign materials
enter the lines.
➢Flush the water lines.
➢Blow out the air lines.
➢Ensure that no more foreign materials can enter the lines after they
have been flushed or blown out.
10l
>30 sec
Versorgung durch den Fußboden
Supply through the floor
Alimentation à travers du plancher
Alimentación a través del suelo
Versorgung über den Fußboden
Supply above the floor
Alimentation au-dessus du plancher
Alimentación por encima del suelo

61 93 739 D3509
D3509.021.01.12.02 08.2013 17
Sirona Dental Systems GmbH 3On-site installation
Installation Requirements TENEO 3.7 Underfloor installation of the PC connections
båÖäáëÜ
3.7 Underfloor installation of the PC connections
Underfloor ins tallation of the PC connections
Depending on the prevailing local conditions, the existing cable set can
be installed in the cable duct of an underfloor installation by an installer
prior to the installation of the treatment center.
The cable channel No. 9 of the installation template is used for this
purpose, see Installation template [ → 13].
PC connection with TENEO USB
Cable set for PC connection with HDMI and USB cable for camera
SiroCam, REF 63 29 655
Cable break
Running cables to the PC
TENEO PC connection cables
Lines L343 (USB repeater), L339 (Ethernet), L406 (HDMI) and protective
ground wire. For PCs without a HDMI output, the Audio line is also
required.
To prevent transmission interference, ensure that the cables are not
crossed.
Laying PC connection cables, TENEO
✔A cable duct is laid from the treatment center to the location of the PC.
✔Free length A of cables at the treatment center end: Length A = 600
mm
1. Pull the lines L343 (USB repeater), L339 (Ethernet), L406 (HDMI)
and protective ground wire of the treatment center through the cable
duct to the location of the PC C. For PCs without a HDMI output,
insert the Audio line. For the USB line L343 the TYPE A connector
must be on the PC side and the TYPE B connector on the chair side.
2. Save the accessory parts for final installation!
ªThe preparation of the connection for the underfloor installation of the
PC is completed.
NOTICE
Electric lines are susceptible to breakages.
Any kinks or twists in the cables could damage their wires. You must
then replace such cables.
➢Ensure that electrical lines do not become kinked or twisted.
C
A

61 93 739 D3509
18 D3509.021.01.12.02 08.2013
3 On-site installation Sirona Dental Systems GmbH
3.7 Underfloor installation of the PC connections Installation Requirements TENEO
Minimum PC requirements
IMPORTANT
Minimum requirements for PC
See document "Installation instructions and system requirements for PC
configuration," (REF 61 94 075) SIVISION digital.

61 93 739 D3509
D3509.021.01.12.02 08.2013 19
Sirona Dental Systems GmbH 4Dimensions, technical data
Installation Requirements TENEO 4.1 Scale 1:20
båÖäáëÜ
4Dimensions, technical data
Dimensions, te chnical data
4.1 Scale 1:20
Scale 1:20
4.1.1 Dimensions of the treatment room
Dimensions of the treatment room
268
10 1/2”
1700
67”
1300
51 3/16”
2500
98 7/16”
300
11 3/4”
A
B
C
400
15 3/4”
D
ARecommended distances from cabinet or wall.
BCenter of the floor cut-out/installation area
CMinimum distance with tray
DHazard warning: The lamp installed here and the tray have a
swivel range which exceeds the specified distances!

61 93 739 D3509
20 D3509.021.01.12.02 08.2013
4 Dimensions, technical data Sirona Dental Systems GmbH
4.1 Scale 1:20 Installation Requirements TENEO
4.1.2 Side view
Side view
1225
48 1/4”
930
36 5/8”
250
9 7/8”
10°
65°
1243
49”
Max. 820
32 1/4”
Min. 370
14 1/2”
Max. 1010
39 3/4”
Min. 810
31 7/8”
Max. 940
37”
Min. 820
32 1/4”
45°
1950
76 3/4”
B
A
360
14 1/8”
1380
54 3/8”
AHeight of the lamp with or without SIVISION digital on the
support arm or lamp support tube
BLEDview