Sirona teneo User manual

MOKOMNN
qbkbl
kÉï=~ë=çÑW==
båÖäáëÜ
fåëí~ää~íáçå=oÉèìáêÉãÉåíë

61 93 739 D3509
D3509.021.01.07.02 02.2011 3
Sirona Dental Systems GmbH
Installation Requirements TENEO Table of contents
båÖäáëÜ
Table of contents
1General information................................................................................................. 5
1.1 Notes on the installation prerequisites ......................................................... 5
1.2 Change history ............................................................................................. 5
1.3 Identification of the danger levels................................................................. 6
2Safety information.................................................................................................... 7
2.1 Installation by qualified personnel ................................................................ 7
2.2 Cellular phones ............................................................................................ 7
2.3 Modifications and extensions of the system................................................. 7
2.4 Power connection......................................................................................... 7
3On-site installation................................................................................................... 8
3.1 Substrate, floor............................................................................................. 8
3.2 DVGW approval ........................................................................................... 8
3.3 Media quality ................................................................................................ 9
3.4 Above-floor installation of supply lines ......................................................... 11
3.5 Underfloor installation of supply lines........................................................... 12
3.5.1 Installation template .......................................................................... 12
3.5.2 Installation of the supply line in the termination panel....................... 13
3.6 Cleaning the air and water pipes.................................................................. 15
3.7 Underfloor installation of the PC connections .............................................. 16
4Dimensions, technical data...................................................................................... 18
4.1 Scale 1:20 .................................................................................................... 18
4.1.1 Dimensions of the treatment room .................................................... 18
4.1.2 Side view........................................................................................... 19
4.1.3 Top view............................................................................................ 20
4.1.4 Top view with options........................................................................ 21
4.2 Mounting plates............................................................................................ 22
4.3 Information on planning for the practice ....................................................... 24
4.4 Technical data.............................................................................................. 25
4.5 Standards/Approvals .................................................................................... 27

61 93 739 D3509
4D3509.021.01.07.02 02.2011
Sirona Dental Systems GmbH
Table of contents Installation Requirements TENEO
5Electromagnetic compatibility................................................................................... 29
5.1 Accessories................................................................................................... 29
5.2 Electromagnetic emission ............................................................................. 30
5.3 Interference immunity.................................................................................... 31
5.4 Working clearances....................................................................................... 33
5.5 Foot control wireless interface ...................................................................... 34
6Checklist................................................................................................................... 35
6.1 Installation site .............................................................................................. 35
6.2 Construction requirements ............................................................................ 36
6.3 IT hardware ................................................................................................... 37
6.4 Network ......................................................................................................... 38
6.5 Data processing ............................................................................................ 39

61 93 739 D3509
D3509.021.01.07.02 02.2011 5
Sirona Dental Systems GmbH General information
Installation Requirements TENEO Notes on the installation prerequisites
båÖäáëÜ
1General information
1.1 Notes on the installation prerequisites
This document describes the installation prerequisites for the TENEO
treatment center.
It contains the following information:
● Required information for practice planning.
● Information for the installer, such as how to implement the
connections for air, water, waste water and suction air as well as the
power supply.
● Information on the cabling of the PCs to be connected.
● Information about electromagnetic compatibility and the prerequisites
for setting up the treatment center.
TENEO installation instructions
The subsequent installation of the treatment center is described in the
installation instructions (Order No.: 61 93 689).
You will also need the drilling template (Order No.: 61 94 000) for the safe
and secure attachment of the treatment center to the floor.
1.2 Change history
Changed in version 2 Chapter: Mounting plates
Changed in version 3 Chapter: Dimensions, template for practice
planning, technical data
Changed in version 4 Chapter: Dimensions, technical data, accessories
Changed in version 5 Chapter: Technical Data
Changed in version 6 Chapter: Accessories
Changed in version 7 Chapter: Checklist

61 93 739 D3509
6D3509.021.01.07.02 02.2011
General information Sirona Dental Systems GmbH
Identification of the danger levels Installation Requirements TENEO
1.3 Identification of the danger levels
Lead text
To prevent personal injury and material damage, please observe the
warning and safety information provided in this document. Such
information is highlighted as follows:
Warning, Caution, Note
WARNING
Warning of bodily injury
For an possible danger that could result in light to serious bodily injury
or death.
CAUTION
Caution against damage
For a possibly harmful situation which could lead to damage of the
product or an object in its environment.
NOTICE
Information to make work easier
For application information and other useful information.

61 93 739 D3509
D3509.021.01.07.02 02.2011 7
Sirona Dental Systems GmbH Safety information
Installation Requirements TENEO Installation by qualified personnel
båÖäáëÜ
2Safety information
2.1 Installation by qualified personnel
Installati on by qualified pe rsonnel
The installation of the supply connections must be carried out only by
qualified personnel.
Regulation s for electrical and water suppl y installations; Reference for suction machines
2.2 Cellular phones
Portable and mobile RF communications equipment may interfere with
medical electrical equipment. Therefore, the use of mobile wireless
phones in medical office or hospital environments must be prohibited.
2.3 Modifications and extensions of the system
Modifications to this system which might affect the safety of the system
owner, patients or other persons are prohibited by law.
For reasons of product safety, this product may be operated only with
original Sirona accessories or third-party accessories expressly approved
by Sirona. The user assumes the risk of using non-approved accessories.
If any devices not approved by Sirona are connected, they must comply
with the applicable standards, e.g.:
● IEC 60950 for information technology equipment (e.g. PC) and
● IEC 60601-1 for medical electrical equipment.
The treatment center monitor must fulfill the requirements of IEC 60950
and IEC 60601-1.
The loudspeaker port of the monitor may be connected only to a device
that complies with IEC 60950 (e.g. a PC) or
IEC 60601-1. Under no circumstances may it be connected to a stereo
system, etc., for example.
If a system is created during the installation process, the requirements of
IEC 60601-1-1 must be fulfilled.
2.4 Power connection
It is essential that you switch off the unit PRIOR to beginning the
installation. There is a risk of electric shock. People can be injured or
electrical components of the unit destroyed.
NOTICE
Professional installation
Comply with the national regulations for electrical installations (e.g.
VDE 0100, VDE 0100, Part 710).
Comply with the national regulations for water supply installations (e.g.
EN 1717, DIN 1988) and sewage installations (e.g. EN 12056-1).
For suction lines: Comply with the specifications in the installation
instructions for "Suction machines".

61 93 739 D3509
8D3509.021.01.07.02 02.2011
On-site installation Sirona Dental Systems GmbH
Substrate, floor Installation Requirements TENEO
3On-site installation
3.1 Substrate, floor
Load capacity:
The minimum load-bearing capacity of the floor must be 0.5 N/cm2
(corresponds to around 500 kg/m2).
Unevenness The floor must be level and horizontal in accordance with DIN 18 202. In
the case of an uneven floor, the steel adapter plate must be used; see
Mounting plates [ ➙ 22].
3.2 DVGW approval
The treatment center has been approved by DVGW and therefore meets
the requirements of standard EN 1717.
It is equipped with a free separation line in the water branch and can thus
be connected directly to the drinking water installation.
0,5
N/cm20,7
lbs/sq in.

61 93 739 D3509
D3509.021.01.07.02 02.2011 9
Sirona Dental Systems GmbH On-site installation
Installation Requirements TENEO Media quality
båÖäáëÜ
3.3 Media quality
empty
Kaltwasser (Trinkwasserqualität)
Cold water (drinking water quality)
Eau froide (eau potable)
Agua corriente (agua potable)
1 bar = 14.5 PSI
p 0,18 bar
u<
> 500 l/min
Wasserhärte
Dureté de l’ eau
Water hardness
Dureza del agua
1,4 mmol l 8° dH/(= )
> 80 m = 0,08 mmµ
> 2,5 l/min
> 2,5 bar
< 6,0 bar
< 7,5 bar
> 50 l/min
> 5,5 bar
K
Suction machine
Air (oil-free)
Cold water (drinking water quality)
KSteam trap

61 93 739 D3509
10 D3509.021.01.07.02 02.2011
On-site installation Sirona Dental Systems GmbH
Media quality Installation Requirements TENEO
Water quality
Lime deposits and corrosion residues in tap water can lead to the
following malfunctions:
● Premature clogging of the filters in the unit
● Rapid clogging of the fine water paths and jets in the treatment
instruments
For these reasons, the following points must be observed:
● For water hardness of 2.2 mmol/l (= 12° dH) or higher, install a water
softener.
● Set dilution water hardness to 1.4 mmol/l (= 8° dH).
● Install a conventional fine filter; fineness: > 80 µm (0.08 mm).
● Installation must be performed in compliance with the
recommendations of the national installation requirements (e.g. EN
1717/DIN 1988).
● The water quality must comply with the national requirements for
drinking water.
● The connection must be made to cold water.
● When laying the water pipe to the treatment center, comply with the
following instructions to reduce the quantity of micro-organisms in the
feed pipe:
– Avoid long stub lines to the treatment center.
– Carry out the installation so that other main consumers (e.g. sink)
are fed from the same line.
– Avoid laying the supply line parallel to hot water pipes.
empty
Air quality
The air for driving the turbines, for cooling the drives and for the cooling
spray must be free from oil, dry and hygienically faultless.
Install steam trap K.
empty
Suction pipe
With a vacuum of pu > 0.18 bar back pressure, the treatment center must
be retrofitted with the "Vacuum limiter" retrofit kit (Order No.: 59 68 826).

61 93 739 D3509
D3509.021.01.07.02 02.2011 11
Sirona Dental Systems GmbH On-site installation
Installation Requirements TENEO Above-floor installation of supply lines
båÖäáëÜ
3.4 Above-floor installation of supply lines
Alternative line feed Above and underfloor installation
The supply lines can be installed above the floor (above-floor installation)
or through the floor (underfloor installation).
For the installation of the supply lines through the floor, see "Underfloor
installation of supply lines" [ ➙ 12].
✔The retrofit kit "Above-floor installation"
(Order No.: 62 05 004) is required for the connection.
➢Lay the ends of the supply pipes, corner valves and lines as shown in
the illustration.
ªThe supply lines are laid.
Suction line
DN40 HT-PP ISO 8283-3 (polypropylene, inner diameter
36.5 mm)
Compressed air supply
Pipe 10x1 mm, corner valve outlet 3/8"
Water supply
Pipe 10x1 mm, corner valve outlet 3/8"
Water drainage
DN40 HT-PP ISO 8283-3 (polypropylene, inner diameter
36.5 mm)
Power supply
3x1.5 mm2
Circuit breaker: for 230 VAC: 16 A slow-blow
for 100-115 VAC: 20 A slow-blow
Recommended: Type B automatic circuit breaker
Cu 10x1 mm
DN 40
200 mm
250 mm
8’’
10’’
> 500 mm
> 20’’
Ø 36,6mm
3/8“

61 93 739 D3509
12 D3509.021.01.07.02 02.2011
On-site installation Sirona Dental Systems GmbH
Underfloor installation of supply lines Installation Requirements TENEO
3.5 Underfloor installation of supply lines
3.5.1 Installation template
We recommend that you order the installation template (Order
No.: 33 15 830) from Sirona for laying the pipe ends in the installation
field. If necessary, you can also prepare the template yourself based on
the diagram below.

61 93 739 D3509
D3509.021.01.07.02 02.2011 13
Sirona Dental Systems GmbH On-site installation
Installation Requirements TENEO Underfloor installation of supply lines
båÖäáëÜ
3.5.2 Installation of the supply line in the termination panel
✔An installation template is available or was prepared.
1. Check the position of the supply lines against the installation template
as per the practice blueprint. Ensure that sufficient space is provided
between the lines and the walls; see "Scale 1:20" [ ➙ 18]. The center
of the hole in the floor must be 268 mm (10 1/2") from the foot of the
treatment center.
2. Lay the ends of the supply pipes, corner valves and lines as shown in
the illustrations.
ªThe top edge of the corner valves for air and water must not project
more than 60 mm from the top edge of the floor.
ªThe suction and drainage pipes must be flush with the top edge of the
floor (a deviation of +5 mm is permissible). The inner diameter of both
pipes is 36.5 mm.
ªThe electric lines must project by at least 500 mm.
ªThe supply lines are laid.
1Water supply
Pipe 10x1 mm, corner valve outlet 3/8"
2Compressed air supply
Pipe 10x1 mm, corner valve outlet 3/8"
3 Suction line
DN40 HT-PP ISO 8283-3 (polypropylene, inner diameter
36.5 mm)
4Water drainage
DN40 HT-PP ISO 8283-3 (polypropylene, inner diameter
36.5 mm)
5Installation pipe
DN40 HT-PP ISO 8283-3 (polypropylene, inner diameter
40 mm)
6Control line for the suction machine and call line
3X1.5 mm2
7Power supply
3x1.5 mm2
Circuit breaker: for 230 VAC: 16 A slow-blow
for 100-115 VAC: 20 A slow-blow
Recommended: Type B automatic circuit breaker
8Not applicable
9Installation pipe
(or corresponding flat conduit) for the PC connection

61 93 739 D3509
14 D3509.021.01.07.02 02.2011
On-site installation Sirona Dental Systems GmbH
Underfloor installation of supply lines Installation Requirements TENEO
3/8“
<5mm
< 60mm
< 3/16“
< 2 3/8“
Ø 36,5 mm
Ø 36,5 mm
>500mm
>20“

61 93 739 D3509
D3509.021.01.07.02 02.2011 15
Sirona Dental Systems GmbH On-site installation
Installation Requirements TENEO Cleaning the air and water pipes
båÖäáëÜ
3.6 Cleaning the air and water pipes
Flushing the air and wate r pipes
CAUTION
Chips and other foreign materials could be flushed and/or blown into the
treatment center.
Metal chips can cause malfunctions of the pneumatic components. The
filters become clogged with foreign materials.
➢During installation, ensure that no chips or other foreign materials
enter the lines.
➢Flush the water lines.
➢Blow out the air lines.
➢Ensure that no more foreign materials can enter the lines after they
have been flushed or blown out.
10l
>30 sec
Versorgung durch den Fußboden
Supply through the floor
Alimentation à travers du plancher
Alimentación a través del suelo
Versorgung über den Fußboden
Supply above the floor
Alimentation au-dessus du plancher
Alimentación por encima del suelo

61 93 739 D3509
16 D3509.021.01.07.02 02.2011
On-site installation Sirona Dental Systems GmbH
Underfloor installation of the PC connections Installation Requirements TENEO
3.7 Underfloor installation of the PC connections
Depending on the prevailing local conditions, the existing cable set can
be installed in the cable duct of an underfloor installation by an installer
prior to the installation of the treatment center.
The cable channel No. 9 of the installation template can be used for this
purpose.
There are two different cable kits:
● PC connection without USB cable
(for second monitor Order No.: 62 09 998)
● PC connection with USB cable
(for the SiroCam digital camera, Order No.: 61 92 897)
Cable bre ak
empty
Running cables to the PC
Lines L343 (USB repeater), L339 (Ethernet), L38 (XGA), audio line and
protective ground wire
To prevent transmission interference, ensure that the cables are not
crossed.
The L38 line (XGA) is very sensitive to interference.
CAUTION
Electric lines are susceptible to breakages.
Any kinks or twists in the cables could damage their wires. Such cables
must be replaced.
➢Ensure that electrical lines do not become kinked or twisted.
NOTICE
L38 assembly
The L38 cable (XGA) is not yet assembled on the PC side. It would be
impossible to pull the cables through when installing them under floor
level if a sub D connector were already connected. The XGA cable L38
should always be pulled. The assembly is described in the TENEO
installation instructions.
B
C
A

61 93 739 D3509
D3509.021.01.07.02 02.2011 17
Sirona Dental Systems GmbH On-site installation
Installation Requirements TENEO Underfloor installation of the PC connections
båÖäáëÜ
✔A cable duct is laid from the treatment center to the location of the PC.
✔Free length A of cables at the treatment center end: Length A = 600
mm
1. Bend the wire B at the front end of cable L38 (XGA) to form a hook.
2. Pull the lines L343 (USB repeater), L339 (Ethernet), L38 (XGA),
audio line and protective ground wire of the treatment center through
the cable duct to the location of the PC C. For the USB line L343 the
TYPE A connector must be on the PC side and the TYPE B connector
on the chair side.
3. Save the accessory parts for final installation!
ªThe preparation of the connection for the underfloor installation of the
PC is completed.
Minimum PC requirements
NOTICE
Minimum requirements for PC
See Document "Installation instructions and system requirements for
PC configuration," (Order no.: 61 94 075) SIVISION digital.

61 93 739 D3509
18 D3509.021.01.07.02 02.2011
Dimensions, technical data Sirona Dental Systems GmbH
Scale 1:20 Installation Requirements TENEO
4Dimensions, technical data
4.1 Scale 1:20
4.1.1 Dimensions of the treatment room
268
10 1/2”
1700
67”
1300
51 3/16”
2500
98 7/16”
300
11 3/4”
A
B
C
400
15 3/4”
D
ARecommended distances from cabinet or wall.
BCenter of the floor cut-out/installation area
CMinimum distance with tray
DHazard warning: The lamp installed here and the tray have a
swivel range which exceeds the specified distances!

61 93 739 D3509
D3509.021.01.07.02 02.2011 19
Sirona Dental Systems GmbH Dimensions, technical data
Installation Requirements TENEO Scale 1:20
båÖäáëÜ
4.1.2 Side view
1225
48 1/4”
930
36 5/8”
250
9 7/8”
10°
65°
1243
49”
Max. 820
32 1/4”
Min. 370
14 1/2”
Max. 1010
39 3/4”
Min. 810
31 7/8”
Max. 940
37”
Min. 820
32 1/4”
45°
1950
76 3/4”
1875
73 3/4”
B
A
360
14 1/8”
1380
54 3/8”
CD
AHeight of the lamp with SIVISION digital on the support arm
or lamp support tube
BHeight of the lamp without SIVISION digital or SIVISION
digital on the tray
CLEDview
DSIROLUX FANTASTIC

61 93 739 D3509
20 D3509.021.01.07.02 02.2011
Dimensions, technical data Sirona Dental Systems GmbH
Scale 1:20 Installation Requirements TENEO
4.1.3 Top view
90°
20°
1250
49 1/4”
412
16 1/4”
363
14 1/4”
1150
45 1/4”
max. 2080
81 7/8”
2000
78 3/4”
860
33 7/8”
1700
67”
30°
25°
25°
65°
41°
268
10 1/2”
200
7 7/8”
max. 200
7 7/8”
1980
78”
max. 2140
84 1/4”
50°
A
B
C
110°
max. 200
7 7/8”
max. 200
7 7/8”
ALength of the treatment center with patient 176 cm tall and
program 2 and fully extended headrest
BMaximum length of the treatment center with motor-driven
headrest
CMaximum length of the treatment center with MultiMotion
headrest