Sit 610 AC3 User manual

610 AC3
CONTROL KNOB (OFF, PILOT, ON)
TEMPERATURE SELECTION KNOB
ON-OFF REGULATING THERMOSTAT
THERMOELECTRIC SAFETY DEVICE
SIT Group
PIN 0085AO0252
MULTIFUNCTIONAL GAS CONTROL

MAIN FEATURES
Multifunctional safety control
with thermoelectric flame
failure device, pressure
adjuster with override device
and on-off thermostat.
No external electric power
supply required.
THERMOSTATIC MULTIFUNCTIONAL
CONTROL
Three-position control knob: off, pilot, on.
Temperature selection knob.
Thermoelectric flame failure device.
Pressure adjuster with override device.
On-off type thermostat.
Resettable safety thermostat.
Pilot outlet with gas flow preselection screw.
Inlet and pilot filters.
Inlet and outlet pressure test points.
610 AC3 is specifically
designed for use
with gas water storage heaters.
Data refer to EN 126

THERMOSTAT
Termostat range Differential (a)
30-70°C < 14°C
35-75°C < 14°C
40-80°C < 14°C
On request: differential (a) < 11°C
SAFETY THERMOSTAT
Set-point Differential (a)
92°C <30°C
a
▲▼
▲
▲
TECHNICAL DATA
DESCRIPTION
• Gas connections: Rp 1/2 ISO 7 (0.75-18 UNS 2B on request)
• Water connections:
Rc 3/4 ISO 7 (3/4 NPT on request)
• Installation position: any position
• Gas families:
I,II and III
• Maximum gas inlet pressure: 50 mbar
• Outlet pressure range: 3-18 mbar
• Working temperature range: 0-80° C
• Pressure regulator: Class C
7 Adjustment screw for gas flow to the
pilot
8 Inlet pressure test point
9 Outlet pressure test point
10 Pilot outlet
11 Thermocouple connection
12 Gas inlet
13 Gas outlet
1 Control knob (off, pilot, on)
2 Temperature selection knob
3 Water connection
4 Adjustment and safety thermostat bulbs
5 Outlet pressure adjustment screw
(P.R. ADJ.)
6 Pressure adjuster override screw
(NO P.R.)
Temperature
Gas flow rate
3
4
7
9
10
11
13
Data refer to EN 126
1
2
5
8
12
6

DIMENSIONS
FLOW RATE AS FUNCTION OF PRESSURE DROP
A
A
6,5
89
112
33.5
3/4 NPT
9.5
22
211
45.5
42
16
2.5
30
36
Rp 3/4
T.C. M9x1
0.750-18UNS
89.5
46
16
Rp1/2
82 27.5
26
10
M10x1
Rp 1/2
7/16-24 NS
Standard
I Family (d = 0.45) Q = 4.3 m3/h ∆p = 5 mbar
II Family (d = 0.6) Q = 3.7 m3/h ∆p = 5 mbar
III Family (d = 1.7) Q = 4.6 kg/h ∆p = 5 mbar
010 18
Q [m3/h d=0.6]
2
1
3
4
5
∆p [mbar]
24 6 812 14 16
6
7
Q [m
3
/h d=0.6]
∆p [mbar]

Ignition
Depress and turn the control knob to the pilot posi-
tion .
Depress the button and ignite the pilot flame while
keeping the knob fully depressed for a few seconds
(fig. 1).
Release the knob and check that the pilot flame stays
lit. If it goes out, repeat the ignition operation.
Main burner ignition
Depress and turn the control knob to the position
corresponding to symbol . On release, the knob
returns to the ON position . Turn the temperature
selection knob to the point corresponding to the
desired temperature (fig. 3).
Pilot position
To close the main burner and keep the pilot flame on,
depress and turn the control knob to the pilot posi-
tion (fig. 1).
Shutdown
Turn the control knob to the OFF position (fig. 4).
CAUTION: after shutting down, wait at least two
minutes before re-igniting so as to allow the flame
failure device to return to the safety position.
OPERATION
fig. 4
fig. 1
fig. 2
fig. 3

INSTALLATION
Main gas connection
The connection is made using gas pipes with Rp 1/2 ISO 7 threading (the valve is available
with 0.75-18 UNS 2B outlet on request). Torque: 25 Nm.
Water connection
The connection flange threading is Rc 3/4 ISO 7 (3/4 NPT on request).
Connection to the pilot burner
Pipes with a 4 mm, 6 mm or 1/4 diameter can be used. Use a nut and olive of appropriate
dimensions. Tighten to 7 Nm torque.
Thermocouple connection
Connect the thermocouple to the magnet unit, checking that the fixing connection is
properly dimensioned. Torque: 3 Nm.
After making the gas connections, check tightness and that the appliance is operating
properly.

SETTINGS AND ADJUSTMENTS
Adjusting the outlet pressure
This adjustment must be made with the
thermostat bulb cold and the knob in
position 5.
Take off the temperature adjustment
knob (A). Check that the pressure adjust-
ment override screw (NO P.R.) is screwed
out completely. Screw in the screw (P.R.
ADJ.) to increase the outlet pressure or
screw it out to reduce it.
Overriding the pressure adjuster
Screw the screw (NO P.R.) fully in.
Adjusting the gas flow rate to the pilot
Screw in the screw (PILOT ADJ.) to reduce
the flow, or screw it out to increase it. To
put the pilot gas flow adjuster out of ser-
vice, fully screw in the screw (PILOT ADJ.)
and then screw it back two complete
turns.
IMPORTANT
At the end of all setting and adjustment
operations, check gas tightness and that
the appliance is operating properly.
Implement the provisions in the Use and Maintenance manual
- code 9.956.610 - for installation, adjustment and use
Taking off temperature adjustment knob
Adjusting the outlet pressure and the flow
rate to the pilot
A
P.R. ADJ.
NO P.R.
PILOT ADJ.

610 AC3
Multifunctional control
with on-off thermostat
and temperature control
knob, for gas water
storage heaters.
Cod. 9.955.741 - R00 GRAPHIC DESIGN BY START - PD - ITALY
SIT La Precisa
Viale dell'Industria 31/33 35129 PADOVA - ITALY
Tel. [phone] - Fax [phone] - Telex 430130 SITEC I