Autonics SPR1 Series User manual

4-Ø6
55
48 223
181
21.3
155
197.6
30 168.5
80°
55
48 223
196
21.3
15
155
212.6
30 168.5
80°
4-Ø6
80
71 250.1
238
21.3
25 187
252.6
40 184.4
4-Ø6
80°
①Bracket
②Indicator
Indicator Color Function
RUN Operation indicator Green LED Turns on in the RUN mode.
MAN Manual control indicator Green LED Turns on when adjusting load output in
the manual control mode.
ALM Alarm indicator Red LED Flashes in alarming status.
OUT Output indicator Red LED Turns on when load control outputs.
③ Display part:
Displays settings of the front display [ DIS] parameter in RUN mode, and displays
parameter and setting value in setting mode.
④ Unit indicator
( : Light ON/ : Light OFF)
Indicator Display
V A
Resistance, load
Voltage
Current
Power
INSTRUCTION MANUAL
Thank you for choosing our Autonics product.
Please read the following safety considerations before use.
Specications
※1: The weight includes packaging. The weight in parenthesis is for unit only.
※Environment resistance is rated at no freezing or condensation.
Ordering Information
DRW171280AB
Connections
Wire Specication by Load Current
Unit Description
Model SPR1-1 SPR1-2 SPR1-3 SPR1-4
Control phase 1-phase
Rated load voltage (50/60Hz) 110VACᜠ220VACᜠ380VACᜠ440VACᜠ
Power supply 100-240VACᜠ50/60Hz
Min. load current 1A
Permissible voltage range 90 to 110% of rated voltage
Power consumption Rated load current 25A/35A/50A: max. 7VA
Rated load current 70A/100A/150A: max. 12VA
Display method 3-digit 7-segemnet LED
Indicator Operation indicator/Manual control indicator: green LED
Alarm indicator/output indicator/unit (V, A) indicator: red LED
Control method
Phase control: normal control mode, constant current/constant voltage/
constant power feedback control mode
Cycle control: xed cycle control mode, variable cycle control mode
ON/OFF control
Applied load Phase control, ON/OFF control: resistance load, inductive load
Cycle control: resistance load
Control input
Auto control: DC4-20mA, 1-5VDCᜡ, ON/OFF contact (no-voltage input),
pulse voltage (5-12VDCᜡ)
Manual control: outside adjuster (10kΩ), inside adjuster (output limit)
Digital input (DI) RUN/STOP switching, AUTO/MAN switching, RESET
Output Alarm 250VACᜠ3A, 30VDCᜡ3A, 1c resistive load
Communication RS485 communication output (Modbus RTU method), max. connection: 31 units
Output range Phase control: 0 to 98% Cycle control: 0 to 100% ON/OFF control: 0%, 100%
Output accuracy
Normal control
: within ±10% F.S. of rated load voltage
Constant current feedback control
: within ±3% F.S. of rated load current
Constant voltage feedback control
: within ±3% F.S. of rated load voltage
Constant power feedback control
: within ±3% F.S. of rated load power
Set method
By front keys, by communication
Functions
Output limit (OUT ADJ), AUTO/MAN selection, control method selection, RESET,
SOFT START, SOFT UP/DOWN, output high/low limit, input correction, input
slope correction, monitoring (control input, load voltage/current/power/resistance,
power supply frequency, heatsink temperature)
Alarm Overcurrent alarm, overvoltage alarm, fuse break alarm, element error alarm,
heater break alarm, heatsink overheat alarm
Cooling method Rated load current 25A/35A/50A: natural cooling
Rated load current 70A/100A/150A: forced air cooling (with the cooling fan)
Insulation resistance Over 200MΩ (at 500VDC megger)
Dielectric strength 2,000VAC 50/60Hz for 1 min (between input terminals and power terminals)
Output leakage current Max. 10mArms
Noise immunity ±2kV the square wave noise (pulse width: 1㎲) by the noise simulator
Memory retention Approx. 10 years (when using non-volatile semiconductor memory type)
Vibration Mechanical
0.75mm amplitude at frequency of 5 to 55Hz in each X, Y, Z direction for 2 hours
Malfunction 0.5mm amplitude at frequency of 5 to 55Hz in each X, Y, Z direction for 10 min
Environ
ment
Ambient temp. -10 to 55℃, storage: -20 to 80℃
Ambient humi. 35 to 85%RH, storage: 35 to 85%RH
Accessory 11-pin connector
Approval ᜢ
Weight※1
Rated load current 25A/35A/50A: approx. 1.6kg (approx. 1.3kg)
Rated load current 70A: approx. 1.65kg (approx. 1.35kg)
Rated load current 100A/150A: approx. 3.2kg (approx. 2.8kg)
Spacing
※
When installing multiple power controllers,
please keep space at least 50mm in
horizontal and 100mm in vertical between
power controllers for heat radiation.
While supplying power to the load or right after
turning off the power of the load, do not touch
the body and heatsink.
Failure to follow this instruction may result in a
burn due to the high temperature.
High Temperature Caution
100100100
4-Ø6
50
Panel
Panel
Safety Considerations
1. Fail-safe device must be installed when using the unit with machinery that may cause
serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment,
ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster
prevention devices, etc.)
Failure to follow this instruction may result in re, personal injury, or economic loss.
2. Install on the device panel, and ground to the bracket separately.
Failure to follow this instruction may result in electric shock or re.
3. Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in electric shock or re.
4. Check 'Connections' before wiring.
Failure to follow this instruction may result in re.
5. Do not disassemble or modify the unit.
Failure to follow this instruction may result in electric shock or re.
Warning
1. Use the unit within the rated specications.
Failure to follow this instruction may result in re or product damage.
2. Use dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in electric shock or re.
3. Do not use the unit in the place where ammable/explosive/corrosive gas, humidity, direct
sunlight, radiant heat, vibration, impact, or salinity may be present.
Failure to follow this instruction may result in re or explosion.
4. Keep metal chip, dust, and wire residue from owing into the unit.
Failure to follow this instruction may result in re or product damage.
5. Since leakage current still ows right after turning off the power or in the output OFF status,
do not touch the load terminal.
Failure to follow this instruction may result in electric shock.
Caution
※
The above specifications are subject to change and some models may be discontinued
without notice.
※
Be sure to follow cautions written in the instruction manual, user manual, and the
technical descriptions (catalog, homepage).
LED Display Slim Power Controller
SPR1 Series
※1: This is only for models with RS485 communication output (SPR1- T ).
※2: When connecting noise lter and capacitor, it is appropriate for EMC.
CAP : Rated load voltage 110VAC-220VAC → 1uF/250VAC
: Rated load voltage 380VAC-440VAC → 0.47uF/500VAC
※2
※2
Noise lter
Rapid fuse
CAP
Load
※Tighten the terminal screw with the below tightening torque.
Rated load
current Specication Alarm output/
power input
Load output
S R, U
25A, 35A,
50A, 70A
Screw M3 M3 M6
Tightening torque 0.5N.m 0.5N.m 5.5 to 6.0N.m
100A, 150A Screw M3 M3 M8
Tightening torque 0.5N.m 0.5N.m 6.5 to 7.0N.m
<Crimp terminal>
a
b
c
Terminal
type
Terminal
number abc
Input
(11-pin) 1 to 11 6 to 7 Max. 1.5 Max. 3.5
※Use crimp terminals or terminals of size specied below.
ab
<Round>
Terminal type a b
Alarm output/power input Min. 3.0 Max. 6.0
Load
output
S Min. 3.0 Max. 8.0
R, U
Rated load current
25A/35A/50A/70A Min. 6.0 Max. 16.0
Rated load current
100A/150A Min. 8.0 Max. 26.0
(unit: mm)
⑤ key:
Enters parameter group, returns to RUN mode, moves
parameters, and saves the setting value.
⑥Setting value adjustment key
: Enters SV setting mode and move digits.
⑦
Output limit adjuster (OUT ADJ)
: Limits output from 0 to 100%.
⑧ 11-pin connector terminal
⑨ Terminal cover
⑩ Alarm output and power input terminals
⑪R, S, U load output terminals
⑫ Cooling fan: For models with the rated load current of 70A/100A/150A, a cooling fan is attached.
⑬Heatsink
Rated load current
Wire specication
Alarm output/
power input
Load output
SR, U
25A/35A/50A/70A AWG 18 to 14 AWG 18 to 14 AWG 13 to 4
100A/150A AWG 4 to 2/0
(unit: mm)
※Please observe all safety considerations for safe and proper product operation to avoid hazards.
※symbol represents caution due to special circumstances in which hazards may occur.
Warning Failure to follow these instructions may result in serious injury or death.
Caution Failure to follow these instructions may result in personal injury or product damage.
※1: Product is not equipped with a rapid fuse inside. Install the suitable fuse for rated load current of
the model separately.
(The performance of the product is guaranteed only when using the fuse provided by us.)
SPR Solid State Power Regulator
NNon-fuse※1
FFuse
NNormal control
FNormal/constant current/constant
voltage/constant power control
NAlarm output
TAlarm+RS485 comm. output
1110VAC
2220VAC
3380VAC
4440VAC
11-phase
25 25A
35 35A
50 50A
70 70A
100 100A
150 150A
1 T FSPR 702 F
Control phase
Item
Rated load current
Rated load voltage
Fuse
Option output
Feedback
control
①
⑧
⑨
⑦
⑤
③
②
⑫
R U
⑫
⑬
S
⑩
⑪
⑥
④
Control input/Comm. output Alarm output/power input
Load output
Alarm Output
(250VAC 3A 1c)
(30VDC 3A 1c)
Resistive Load
100-240VAC
50/60Hz
1 2 3 4 5
N.C. N.O. LCOM N
※1
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
VR
ON/OFF
4-20mA
1-5
VDC
RUN/STOP
AUTO/MAN
RESET
RS485
A(+)
B(-)
R S U
Rated load current 25A/35A/50A
Rated load current 100A/150A
Rated load current 70A
Dimensions
6.8
6.8
6.8
Removing the Case
Replacement of Fuse
②
①
Case
xing
bolts
Spec. of case fixing bolts
Rated load current Spec. of bolts
25A, 35A, 50A, 70A M3
100A, 150A M4
Fuse xing bolts
Fuse
For replacing the fuse, please use the recommended fuse which has the below specications.
(manufacture: BUSSMANN)
※The performance of the product is guaranteed only when using the fuse provided by us.
Recommended fuse specifications
Spec. of fuse fixing bolts
Rated load current Spec. of bolts
25A, 35A, 50A, 70A M6
100A, 150A M8
Rated load
current Model Rated load current Model Rated load current Model
25A 50FE 50A 80ET 100A FWH-150B
35A 63ET 70A 100FE 150A FWH-200B

RS485 Communication Output
Cautions during Use
1. Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected accidents.
2. Use the product, after 3 sec of supplying power.
3. Before use, set the mode and function according to the specification. Especially, be cautious that the product
does not operate when OUT ADJ. is set to 0%. Since changing the mode/parameter during operation may
result in malfunction, set the mode and function after disconnecting load output.
4. Re-supply the power to the unit after the unit is discharged completely.
Failure to follow this instruction may result in malfunction.
5. To ensure the reliability of the product, install the product on the panel or metal surface vertically to the ground.
6. Install the unit in the well ventilated place.
7. While supplying power to the load or right after turning off the power of the load, do not touch the body and
heat sink. Failure to follow this instruction may result in a burn due to the high temperature.
8. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power.
9. Do not wire to terminals which are not used.
10. Since inter element can be damaged when using with coil load, inductive load, etc., the inrush current must
be under the rated load current.
11. Do not use near the equipment which generates strong magnetic force or high frequency noise.
12. This unit may be used in the following environments.
①Indoors (in the environment condition rated in 'Specifications') ②Altitude max. 2,000m
③Pollution degree 2 ④Installation category III
※
Applicable for models with RS485 communication output through option output (SPR1- T ).
Please refer to ' Ordering Information'.
1. Communication Specifications
Comm. protocol Modbus RTU Comm. speed
2400, 4800, 9600, 19200,
38400 bps
Connection method RS485
Application standard Compliance with EIA RS485 Comm. response time 5 to 99ms (default: 20ms)
Max. connections 31 units (address: 1 to 99) Start bit 1-bit (xed)
Synchronization method Asynchronous Data bit 8-bit (xed)
Comm. method Two-wire half duplex Parity bit None, Even, Odd
Comm. distance Max. 800m Stop bit 1-bit, 2-bit
2. Application of system organization
※
It is recommended to use Autonics communication converter; SCM-WF48 (Wi-Fi to RS485·USB wireless
communication converter, sold separately), SCM-US48I (USB to RS485 converter, sold separately),
SCM-38I (RS232C to RS485 converter, sold separately). Please use twisted pair wire, which is suitable
for RS485 communication, for SCM-WF48, SCM-US48I and SCM-38I.
Terminating
resistance
(100 to 120Ω)
B(-)
A(+)
ON OFF
A(+)
RS485
DEVICE
#1
RS485
DEVICE
#2
RS485
DEVICE
#30
RS485
DEVICE
#31
A(+) A(+)B(-) B(-) B(-)
Computer
RS485
Comm.
converter
RS232C/
USB/Wi-Fi
Major Products
Photoelectric Sensors Temperature Controllers
Fiber Optic Sensors Temperature/Humidity Transducers
Door Sensors SSRs/Power Controllers
Door Side Sensors Counters
Area Sensors Timers
Proximity Sensors Panel Meters
Pressure Sensors Tachometer/Pulse (Rate) Meters
Rotary Encoders Display Units
Connector/Sockets Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System (Fiber, CO₂, Nd: YAG)
Laser Welding/Cutting System
http://www.autonics.com
HEADQUARTERS:
18, Bansong-ro 513beon-gil, Haeundae-gu, Busan,
South Korea, 48002
TEL: [phone]
E-mail: [email protected]
DRW171280AB
User Manual for Communication
For the detail information and instructions, please refer to user manual for communication, and be sure
to follow cautions written in the technical descriptions (catalog, homepage).
Visit our homepage (www.autonics.com) to download manuals.
Comprehensive Device Management Program [DAQMaster]
DAQMaster is a comprehensive device management software for setting parameters and monitoring
processes. DAQMaster can be downloaded from our website at www.autonics.com.
Item Minimum specications
System IBM PC compatible computer with Pentium Ⅲor above
Operations Windows 98/NT/XP/Vista/7/8/10
Memory 256MB+
Hard disk 1GB+ of available hard disk space
VGA Resolution: 1024×768 or higher
Others RS232C serial port (9-pin), USB port
B(-)
A(+)
Actual input signal [%]
Functions
Output limit (OUT ADJ)
SOFT UP/DOWN [U-T/D-T]
Input slope correction [SPN]
Input correction [INB]
RUN/STOP switching
RUN/STOP status of the power controller can be switched with the external
RUN/STOP contact.
In the RUN mode, the operation indicator on the front turns on. ON/OFF
RESET
In the event of system anomalies and alarms, RESET input restarts the
power controller.(Parameters are not initialized.)
Or, hold the
, keys
for 2 sec, to operates RESET.
ON
AUTO/MANUAL selection
Operation mode (auto control/manual control) of the power controller can be
selected with the external AUTO/MAN contact.
In the manual control mode, the manual control indicator on the front turns on. ON/OFF
When the power is supplied, this function is able to
protect the load when it controls load (molybdan,
white gold, infrared lamp) with inrush current or the
width of rising temperature in big (SV is big).
SOFT START set time (T) is the required time that
output reaches to 100%, and it is differentiated by
OUT ADJ set value.
Unlike SOFT START which operates only once at
supplying power, this function protects load from the
inrush current in the RUN mode. When reached to
the target output value, operation stops.
Output high limit/low limit value [H-L/L-L]
This function is to limit output range to protect load.
It compensates the offset between actual input value
and measured input value.
E.g.) When input monitoring value is 5% at 4mA in
DC4-20mA control input, setting INB to -5
calibrates the input monitoring value to 0%.
Measured input signal [%] Output [%] Output [%] Output [%]
Measured input signal [%]
SOFT START set time
SOFT DOWN set time
SOFT UP set time
Time
Time
When output applied to load is 100%,
This function will be [Control input (%) × OUT ADJ (%) =
Output] and it controls the power supplied into the load.
Although control input is 100% (5V or 20mA), the output
is the 50% which is proportioned with OUT ADJ.
0 50 100
Control input [%]
Setting value = 50%
Setting value = 100%
100
75
50
25
: Actual input signal (%)
: Input corrected signal (%)
: Actual input signal (%)
: Input corrected signal (%)
Actual input signal [%]
It compensates the gain of the measured 100% input
for actual 100% input value.
Calibrated monitoring value=Monitoring value+ Monitoring value
×SPN
100- SPN
E.g.) When the input monitoring value is 99% at 4mA in
DC4-20mA control input,
setting SPN to 1
calibrates
the input monitoring value to 100%.
SOFT START [S-T]
When output applied to load is 50%,
0
100
50
0
100
50
SOFT START set time
A: SOFT START function nished.
B: SOFT UP function nished.
C: SOFT DOWN function nished.
100
100
100
100
80
80
75
75
60
60
40
40
50
50
20
20
25
25
0
0
※
※This function can not be used for ON/OFF control method.
※
※This function can not be used for ON/OFF control method.
※
※This function can not be used for ON/OFF control method.
Alarm
Type Error Operation Clear alarm Display priority
Element (SCR) error alarm
※
1
SCR
Output stops.
(SCR OFF)
- Re-supply the power.
- RESET
- Switch to STOP mode
1
Overcurrent alarm※
1
O-C 2
Fuse break alarm FUS 3
Heatsink overheat alarm TEM 4
Overvoltage alarm※
1
O-V 5
Heater break alarm※
1
H-B Continues
operation
Automatically cleared when
returning within the setting range 6
※
1: This is only for feedback control models.
※
For models with alarm output, the error message and alarm indicator ash at the same time, and alarm output turns on.
※
When multiple alarms occur at the same time, the highest priority error message will be displayed based on priority.
1) Element (SCR) error alarm
Even though output is 0%, if the current of 10% or more of the rated load current ows for over 3 sec
continuously, element error alarm occurs and output stops.
2) Overcurrent alarm [OCU/OCT]
This function protects the load from overcurrent.
If the current ows over the overcurrent alarm setting value and setting delay time, overcurrent alarm
occurs and output stops.
3) Heatsink overheat alarm
When the temperature of a heatsink is over 85℃, heatsink overheat alarm occurs and output stops.
4) Overvoltage alarm [OVV/OVT]
This function protects the load from overvoltage.
If the current ows over the overvoltage alarm setting value and setting delay time, overvoltage alarm
occurs and output stops.
5) Heater break alarm [HBV]
Comparing the full load resistance value and the current load resistance value, if the current load
resistivity is maintained under the setting value for over 3 sec continuously , heater break alarm occurs.
Output does not stop and operates normally.
Current load resistivity(%) = Full load resistance value ×100
Current load resistance value
Derating Curve
Rated load current 25A
Rated load current 50A
Rated load current 100A
Rated load current 35A
Rated load current 70A
Rated load current 150A
Load current [A]
35
21
28
14
7
0
010 20 30 40 50 60 70
Ambient temperature [℃]
Load current [A]
70
42
56
28
14
0
010 20
30 40 50 60 70
Ambient temperature [℃]
Load current [A]
150
90
120
60
30
0
010 20 30 40 50 60 70
Ambient temperature [℃]
Load current [A]
100
60
80
40
20
0
010 20 30 40 50 60 70
Ambient temperature [℃]
Load current [A]
50
30
40
20
10
0
010
20 30 40 50 60 70
Ambient temperature [℃]
Load current [A]
25
15
20
10
5
0
010 20 30 40 50 60 70
Ambient temperature [℃]
3525
Monitoring group Parameter 1 group[PR1] Parameter 2 group[PR2]
4 sec2 sec
3 sec 3 sec
RUN mode
※If there is no key input for 30 sec while setting SV or the parameters, the new settings are ignored, and
the unit will return to RUN mode with previous settings.
※Hold the key for 3 sec while in setting mode to return to RUN mode.
Parameter Group
Setting range: 0 to 100 sec
※
When control method [C-M]is ONF, settings can not be
changed.
3 sec
2 sec
SOFT START
S-T 000
※1
SOFT UP
U-T 000
D-T 000
SOFT DOWN
Output low-limit
value
L-L 000
Output high-limit
value
H-L 100
※2
PR1
Setting range
: 0% ≤ Output low-limit value[L-L] ≤ Output high-limit value[H-L] ≤ 100%
※1: : Press any key among , , .
※2: Press the key once after changing the setting value, to save the setting value and move to the
next parameter
※Hold the key for 3 sec to save the setting value and return to RUN mode after changing the
setting value.
※Dotted parameters may not appear by model type or other parameter settings.
Parameter 1 group
Monitoring group
Setting range: 0 to 120%
Setting range: 1 to 99
Setting range: 0 to 100 sec
Setting range: 0 to 120%
Setting range: 10 to 100%
Setting range: 0 to 100 sec
※
Displayed only formodelswithRS485communicationoutput.
※Displayed only for feedback control models.
Setting range: -99 to 99%
Setting range: 5 to 99ms
Setting range:
Setting range: -99 to 99%
3 sec
4 sec
Control input DC4-20mA 1-5VDC 5-12VDC ON/OFF contact
Enables Disables
INT 420
Control method
C-M PA
E-R OFF
External output
limit adjuster
OVV 120
Overvoltage alarm value
PRT NON
Comm.
parity bit
DIS IN
Front display
HBV 010
Heater break alarm value
CM.W EN.A
Comm. write
Input correction
INB 00
Overvoltage alarm
delay time
OVT 005
Comm. stop bit
STP 2
Overcurrent alarm value
OCV 120
Comm. address
ADR 001
Lock
LOC OFF
Input slope correction
SPN 00
Full load
auto recognition
F-L OFF
Comm. response
waiting time
RW.T 020
Overcurrent alarm
delay time
OCT 005
Comm. speed
BPS 96
Parameter reset
INI NO
1-5
LC1
YES
DsA
512
LC2
ONF
※2
PR2
PR1 PR2
OFF
LC1
LC2
RS485 comm.
COM
Load voltage Load current Load power
L-V L-A L-W
EVE ODD
1
ON
ON
9,600bps 19,200bps 38,400bps 2,400bps 4,800bps
192 384 24 48
Resistance
and input
Setting range: Normal control PA, F-C, V-C, ONF
Feedback control
(normal/constant current/constant voltage/
constant power control)
PA, V-F, C-F, W-F,
F-C, V-C, ONF
Phase -
Constant
voltage
Phase -
Constant
current
Phase -
Constant
power
Cycle-Variable
V-F C-F W-F
ONFV-C
Cycle-Fixed
F-C
ON/OFF
Phase -
Normal
※1: : Press any key among , , .
※2: Press the key once after changing the setting value, to save the
setting value and move to the next parameter
※Hold the key for 3 sec to save the setting value and return to RUN
mode after changing the setting value.
※
Dotted parameters may not appear by model type or other parameter settings.
: Available to check/set
: Available to check/Unavailable to set
※1
Parameter 2 group
※
Hold the , , keys for 5 sec, to enter parameter reset parameter.
RUN mode
RUN mode
Measuring range: 0 to rated voltage range[V]
Measuring range: 0 to rated current range[A]
Measuring range: 0 to rated power range[VA]
Measuring range: Percentage [%] of the currently measured
resistance value compared to the set
resistance value of full load auto recognition.
RUN mode
Control input
IN 100
※1
Load voltage
L-V 220
L-A 50
Load current
Load power
L-W 10
Load resistance
L-R 50
Heatsink temp.
TMP 25
Power supply
frequency
FRQ 60
※2
Measuring range: 0 to 100%
Measuring range: 0 to 100℃
Measuring range: 50, 60Hz
※
Displayed only for feedback control models.
Setting range: Normal control IN
Feedback control
(normal/constant current/constant voltage/
constant power control)
IN, L-V, L-A, L-W