Siterwell GS528A-MG User manual

OPERATION
PRODUCT SPECIFICATIONS:
SMOKE ALARM USER MANUAL
PHOTOELECTRIC SMOKE ALARM GS528A-MG
Testing: Test weekly by pushing the test button on the cover and holding it down for a minimum of 5 seconds.
this will sound the alarm if the electronic circuitry, horn, and battery are working properly.
DO NOT use an open flame to test your alarm, you could damage the alarm or ignite combustible materials and
start a structure fire.
CAUTION: Due to the loudness (85 decibels) of the alarm, Always stand an arms-length away from the unit
when testing. Test the alarm weekly to ensure proper operation. Erratic or low sound coming from your alarm
may indicate a defective alarm.
LED indicators: This smoke alarm is equipped with red LED indicators.
Standby Condition: The red LED will flash every 32 seconds to indicate that the smoke alarm is operating properly.
Alarm Condition: When the alarm senses products of combustion and goes into alarm, the red LED will flash
rapidly (one flash per second).The rapid flashing LED and pulsating alarm will continue until the air is cleared
or the test button is released.
Power:
Operaon Current:
Sensor Type:
Alarm Volume:
DC 9V baery
<11uA(standby), <30mA (alarm)
Photoelectric
>85dB(A) at 3 meters
Low baery warning:
Averssement de baerie faible:
Alarm Sensivity:
Comply With:
6.5-7.8V
6.5-7.8V
1.51-2.64%/ OBS
UL217 &CAN/ULC-S531
GS528A-MG

INSTALLATION NOTE
Low battery trouble indication: An intermittent “chirp” accompanied by a red LED flash every 32 seconds indicates
a low battery.
Fault indication: This chirp will occur between the flashes of the red LED indicator light.
SMOKE SENSING CHAMBER OPERATION: This alarm will “chirp” if any of the components in the smoke sensing
chamber fail. This chirp will occur between the flashes of the red LED indicator light. (If the chirp occurs at the same
time as the red LED flash, indicating a low battery information).
NOTE: WEEKLY TESTING IS REQUIRED
DANGER: If the alarm sounds, and it is not being tested, it means the unit is sensing smoke,
THE SOUND OF THE ALARM REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.
SITERWELL ELECTRONICS CO ., LIMITED
Address:NO.666 Qingfeng Road, Jiangbei District, Ningbo, Zhejiang Province, China
Tel: [phone] Fax: [phone]
E-mail: [email protected] Http://www.china-siter.com
If you are not sure about the insulation in your mobile home, or if you notice that the outer walls
and ceiling are either hot or cold, install the alarm on an inside wall. For minimum protection,
install at least one alarm close to the bedrooms. For additional protection, see SINGLE FLOOR
PLAN in Figure 3 and MULTIPLE FLOOR PLAN in Figure 4.
• When mounting an alarm on the ceiling, locate it at a minimum of 4"(10cm)
from the side wall (see figure 1).
• When mounting the alarm on the wall, use an inside wall with the top edge
of the alarm at a minimum of 4"(10cm) and a maximum of 12"(30.5cm)below
the ceiling (see figure 1).
• Put smoke alarms at both ends of a bedroom hallway or large room if the
hallway or room is more than 30 ft (9.1 m) long.
• Install Smoke Alarms on sloped, peaked or cathedral ceilings at or within
3 ft (0.9m) of the highest point (measured horizontally). NFPA72 states:
"Smoke alarms in rooms with ceiling slopes greater than 1 ft in 8 ft (.3m in
2.4m)horizontally shall be located on the high side of the room. " NFPA 72
states: "A row of alarms shall be spaced ac'usmated within 3 ft (0.9m) of
the peak of the ceiling measured horizontally" (see figure 2).
SINGLE FLOOR PLAN Figure 3
Smoke or smoke/CO alarms for required protection
Smoke or smoke/CO alarms for additional protection
Smoke alarm with silence control for additional protection MULTIPLE FLOOR PLAN
Figure 4