SKYDANCE D1-L User manual

23mm
170mm
50mm
● Comply with the DMX512 standard protocols.
● Digital numeric display, set DMX decode start address by buttons.
● RDM function can realize intercommunication between DMX master and decoder.
For example, DMX decoder address can be set by DMX master console.
● PWM frequency 2000/500Hz selectable.
● Logarithmic or linear dimming curve selectable.
● Stand-alone dynamic mode and dimmer mode selectable,
which be controlled by buttons with built-in programs, instead of DMX signal.
● Over-heat / Over-load / Short circuit protection, recover automatically
Output type Constant voltage
Output power 180-360W
Output voltage 12-24VDC
Output current 1CH,15A
Input voltage 12-24VDC
Input current 15.5A
User Manual Ver 1.0.2
Technical Parameters
Input and Output
Warranty and Protection
5 years
Protection
Reverse Polarity
Over-heat
Over-load
Short circuit
Warranty
Operation temperature
Case temperature (Max.)
Environment
IP rating IP20
Ta: -30
O
C ~ +55
O
C
T c: +85
O
C
Model No.: D1-L
Features
Page 1
Mechanical Structures and Installations
RDM/Stand-alone function/Two PWM frequency/ /Numeric display/Multiple protectionLogarithmic or linear dimming
Safety and EMC
EMC standard (EMC)
Certification CE,EMC,LVD
Safety standard(LVD)
EN55032:2015,
EN61000-3-2:2014,
EN61000-3-2:2013,
EN55024 :2010/A1:2015
1 Channel Constant Voltage DMX512 & RDM Decoder
D1-L 1 Channel Constant Voltage DMX512 & RDM Decoder
DMX input +
DMX input -
DMX output -
DMX output +
GND
Power input -
Power input +
LVD
Wiring Diagram
Installation rack
EN 61347-1:2015
EN 61347-2-11:2015
Note:
1. An DMX signal amplifier is needed if more than 32 decoders are connected, or use overlong signal line,
signal amplification should not be more than 5 times continuously.
2. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W
90-120Ω terminal resistor at the end of each DMX signal line.
D+
V+
D-
GND
INPU T 12-2 4VDC
OUTP UT
DMX IN
DMX OU T
V+
V+
V+
V-
V-
V-
V-
D+
D-
GND
D+
V+
D-
GND
INPU T
12-2 4VDC
OUTP UT
DMX IN
DMX OU T
V+
V+
V+
V-
V-
V-
V-
D+
D-
GND
AC100-240V
Power Supply
12-24VDC
Constant Voltage
Single color LED strip
DMX
Master
Setting key Digital display
GND
LED Output +
LED Output -

User Manual Ver 1.0.2 Page 2
D1-L 1 Channel Constant Voltage DMX512 & RDM Decoder
Dimming curve setting
Linear dimming cur ve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 8 0 90 100
Brightness(%)
10 20 30 4 0
Gamma=1.6
50 60 70 8 0 90 100
Brightness(%)
10 20 30 4 0
Gamma=1.0
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
● Long press ◀ and ▶ key for 2s, restore factory default parameter, display"RES".
● Factory default parameter: DMX decode mode, DMX decode start address is 1, high PWM frequence output,
logarithmic brightness curve, dynamic mode number is 1, dimmer mode number is 1, disable automatic blank screen.
● Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
● Short press M key, when display L-1~L-8, enter stand-alone dimmer mode.
● Press ◀ or ▶ key to change dimmer mode number(L-1~L-8).
● Each dimmer mode can adjust brightness independently.
Long press M key for 2s, prepare for setup brightness(b00~bFF).
Press ◀ or ▶ key to adjust brightness value.
Short press M key, or timeout 10s, quit setting.
Stand-alone dimmer mode
(L-1~L-8)
Malfunctions analysis & troubleshooting
1. DMX decode address error.
Causes
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
1. No power.
2. Wrong connection or insecure.
Wrong color
Malfunctions
Uneven intensity
between front and
rear,with voltage drop
No light
Stand-alone dynamic mode
● Enter stand-alone dynamic mode only when DMX signal is disconnected or lost.
● Short press M key, when display P-1~P-3, enter stand-alone dynamic mode.
● Press ◀ or ▶ key to change dynamic mode number(P-1~P-3).
● Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press ◀ or ▶ key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
Speed
(8 level)
Brightness
(10 level,100％)
(P-1~P-3)
1. Set corrrect decode address.
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply.
4. Add power repeater.
1. Check the power.
2. Check the connection.
Stand-alone dimmer mode
Restore factory default parameter
Stand-alone dynamic mode
● Short press M key, when display 001~999, enter DMX mode.
● Press ◀ or ▶ key to change DMX decode start address(001~999),
long press for fast adjustment.
● If there is a DMX signal input, will enter DMX mode automatically.
● DMX Dimming: Each D1-L DMX decoder occupy 1 DMX address
when connecting the DMX console.
DMX mode
DMX mode
(001~999)
● Long press M and ◀ key in the same time for 2s, prepare for setup system parameter: output PWM frequence, output brightness
curve, automatic blank screen. short press M key to switch three item.
● Output PWM frequence: short press ◀ or ▶ key to switch 500Hz("F-L") or 2KHz("F-H").
Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
● Output brightness curve: short press ◀ or ▶ key to switch linear curve("C-L") or logarithmic curve("C-E").
● Automatic blank screen: short press ◀ or ▶ key to switch enable ("bon") or disable("boF") automatic blank screen.
● Long press M key for 2s or timeout 10s, quit system parameter setting.
Operation
System parameter setting
Dynamic mode list
Name
P-1
P-2
P-3
No.
white fade in and fade out
white jump
white flash