SKYDANCE T20 User manual

T20T20-3
T20-2
T20-1
● Touch panel 1/2/3/4 zone dimming switch RF remote.
● Each zone can remote control multiple Skydance’s 2.4G LED controllers.
● Ultra sensitive high strength glass touch panel.
● Touch keys with chord tones and LED indicator.
● Free installation, no wiring, removable.
● AAA x 2 attery powered.b
● White & Black glass panel available.
User Manual Ver 1.0.7
Technical Parameters
Model No.: T20,T20-1,T20-2,T20-3
1-4 Zone dimming switch/Glass touch panel/Wireless remote 30m distance/AAA x 2 battery
Features
Page 1
Mechanical Structures and Installations
Wall Mounted Touch Panel
LVD RED
ON key
Short press: Turn on the light of each zone.
Long press(1-6s): Dimming up when light is on.
OFF key
Short press: Turn off the light of each zone.
Long press(1-6s): Dimming down when light is on.
Long press(5s) : Turn on or turn off tone when light is off.
Zone1
Zone1
Zone2
Zone1
Zone2
Zone3
Zone1
Zone2
Zone3
Zone4
T20,T20-1,T20-2,T20-3 Wall Mounted Touch Panel
T20T20-3T20-2T20-1
Key function
1 Zone switch 2 Zone switch 3 Zone switch 4 Zone switch
Warranty
5 years
Warranty
Operation temperature
Case temperature (Max.)
Environment
IP rating IP20
Ta: -30
O
C ~ +55
O
C
T c: +65
O
C
Typical base as below:
European style 86 size
Touch panel Baseplate Base
Uninstall
Installation diagram:
86.00 mm
86.00 mm
61.00 mm
61.00 mm
20.50 mm
Installation rack
Battery compartments
To fix the panel, two options are offered for selection:
Option 1: fix it on the wall with two screws.
Option 2: adhere it to the wall with paster.
Weight
160g
Gross weight
Net weight
190g
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certification CE,EMC,LVD,RED
EN 62368-1:2020+A11:2020
Safety standard(LVD)
Input and Output
Output signal RF 2.4GHz( )
Working voltage 3VDC AAA x 2( )
＜5mA Without tune( )
＜20mA with tune( )
Standby current ＜20μA
Standby time 1 year
Remote distance 30m (Barrier-free space)
Working current

Touch Panel work as RF remote (two match ways)
Use the controller’s Match key
Match:
Short press match key, immediately press ON
key of the touch panel.
The LED indicator fast flash a few times
means match is successful.
Use Power Restart
Match:
Switch off the power of the receiver, then switch on power,
repeat again.
Immediately short press ON key 3 times on the touch panel.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power of the receiver, then switch on power,
repeat again.
Immediately short press ON key 5 times on the touch panel.
The light blinks 5 times means all matched remotes were deleted.
Delete:
Press and hold match key for 5s to delete all match.
The LED indicator fast flash a few times
means all matched remotes were deleted.
End user can choose the suitable match/delete ways. Two options are offered for selection:
User Manual Ver 1.0.7 Page 2
T20,T20-1,T20-2,T20-3 Wall Mounted Touch Panel
Safety information
1. Read all instructions carefully before you begin this installation.
2. When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the batter y.
3. If no response from the receiver, please re-match the remote.
4. Gently handle remote, beware of falling.
5. For indoor and dry location use only.