SKYDANCE TW1 User manual

1
User Manual Ver 1.0.0
1-4 color/Glass touch panel/Touch color wheel/Wireless remote 30m distance/CR2032 battery
Model No.: TW1,TW2,TW4
Wall Mounted Touch Panel
● Touch panel 1-4 color RF remote.
● Each Touch panel can remote control multiple LED controllers.RF 2.4G
● Ultra sensitive high strength glass touch panel with touch color wheel in the middle .
● Touch keys with blue/red LED indicator.
● Free installation, no wiring, removable.
● CR2032 battery powered.
Features LVD RED
TW4
TW2
TW1
1 Zone Dimming 1 Zone CCT 1 Zone RGB/RGBW
Technical Parameters
Output signal RF(2.4GHz)
Working voltage 3VDC(CR2032)
Working current <8mA
Standby current <16μA
Standby time 1 year
Remote distance 30m (Barrier-free space)
To fix the panel, two options are offered for selection:
Option 1: fix it on the wall with two screws.
Option 2: adhere it to the wall with paster.
Input and Output
Operation temperature
Environment
Ta: -30
O
C ~ +55
O
C
Gross weight
Size
Package
Case temperature (Max.)
IP rating IP20
Ta: +65
O
C
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certication CE,EMC,LVD,RED
EN 62368-1:2020+A11:2020
Safety standard(LVD)
5 years
Warranty
Mechanical Structures and Installations
86.00 mm
86.00 mm
9.50 mm
Match with RF LED controller (two match ways)
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key on the touch panel.
The LED indicator fast flash a few times means match is successful.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 3 times on the touch panel.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 5 times on the touch panel.
The light blinks 5 times means all matched remotes were deleted.
Delete:
Press and hold match key for 5s to delete all match.
The LED indicator fast flash a few times means all matched remotes
were deleted.
End user can choose the suitable match/delete ways. Two options are offered for selection:
Baseplate Base
Uninstall
Installation diagram:
Touch panel
Note: If the LED indicator is not on when press key,
it is due to dead battery or bad contact caused by
multiple plugging, please replace the battery,
or raise the battery shrapnel with a screwdriver
L100x W92 x H16.5mm
0.137kg

● TW1 Single color panel
● TW2 Dual color panel
Turn on/off light.
Turn on/off light.
Short press run next dynamic mode, long press 2s run mode-cycle.
Turn on/off light.
For dynamic mode, adjust speed, short press 10 levels, long press 2s get the default speed.
For static color, adjust saturation, short press 11 levels, long press 1-6s for continuous adjustment.
● TW4RGB/RGBW panel
For RGB light, short press turn on/off white(RGB mix), long press 1-6s adjust saturation.
For RGBW light, short press turn on/off W channel, long press 1-6s adjust W brightness.
Keyfunction
Brightness +,10 levels.
Brightness -,10 levels.
Touch to change brightness.
Short press set 100% brightness.
Short press set 100% brightness.
Touch to change color temperature.
Short press recall scene, Long press 5s to save the current state intoⅠ/Ⅱ/Ⅲ/Ⅳ.
Short press recall scene, Long press 5s to save the current state intoⅠ/Ⅱ/Ⅲ/Ⅳ.
Brightness +,10 levels.
Brightness -,10 levels.
Touch to change static RGB color.
Short press recall scene, Long press 5s to save the current state intoⅠ/Ⅱ.
Safety information
1. Read all instructions carefully before you begin this installation.
2. When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery.
3. If no response from the receiver, please re-match the remote.
4. Gently handle remote, beware of falling.
5. For indoor and dry location use only.
2
User Manual Ver 1.0.0