Skyjack SJ6826 RT User manual

221587ACA
November 3 2022
ANSI/CSA
OPERATION
MANUAL
ROUGH TERRAIN SCISSORS
SJ6826 RT, SJ6832 RTE

SJ6826 RT, SJ6832 RT: A200 000 001 & above
This manual is for MEWPs with serial numbers:
Please refer to the website (www.skyjack.com) for
contact information, other Serial Numbers, the most
recent Technical Manuals, and USB software.
The original instructions are in English.

3
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
The Safety Alert symbol identifies important safety
messages on MEWPs, safety signs in manuals or
elsewhere. When you see this symbol, be alert to
the possibility of personal injury or death. Follow the
instructions in the safety message.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in death
or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury. It may also be used to alert
against unsafe practices.
IMPORTANT
IMPORTANT indicates a procedure essential for
safe operation and which, if not followed, may
result in a malfunction or damage to the MEWP.
Red
DANGER.
Orange
WARNING.
Yellow
CAUTION.
Green
Emergency-
lowering
procedure.
Blue
Safety
information.
THIS SAFETY ALERT SYMBOL MEANS ATTENTION!
BE ALERT! YOUR SAFETY IS INVOLVED.

4
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Notes

5
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Section 1 – About this Mobile Elevating Work Platform (MEWP) . . . . . . . . . . . . . . . . . . . . 9
1.1 Read and heed .....................................................................9
1.1-1 Mobile Elevating Work Platform (MEWP) definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1-2 Purpose of equipment ...........................................................9
1.1-3 Use of equipment ...............................................................9
1.1-4 Operation manual ...............................................................9
1.1-5 Operator ......................................................................9
1.1-6 Service policy and warranty .......................................................9
1.1-7 Ownership of MEWP .............................................................9
1.1-8 Optional equipment .............................................................9
1.1-9 Scope of this manual ...........................................................10
1.2 Primary assemblies ................................................................11
1.3 Serial number nameplate ...........................................................12
1.4 Maintenance responsibility ..........................................................13
1.4-1 Operator .....................................................................13
1.4-2 Maintenance and inspection schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.4-3 Owner .......................................................................13
Section 2 – General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1 Electrocution hazards ..............................................................15
2.1-1 Minimum distance from electrical conductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2 Safety instructions ................................................................16
2.3 Fall-protection ....................................................................19
2.4 Worksite inspection ................................................................19
Section 3 – Familiarization ..................................................21
3.1 Overview of the MEWP .............................................................22
3.2 Manual storage box ................................................................23
3.3 Control functions ..................................................................23
3.3-1 Main power disconnect switch ....................................................23
3.3-2 Base control console ...........................................................24
3.3-3 Platform control console .........................................................25
3.4 Features and devices ..............................................................26
3.4-1 Lowered travel position and elevated travel position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4-2 Drive speed ...................................................................26
3.4-3 Tilt switch ....................................................................26
3.4-4 Brake release system ...........................................................26
3.4-5 Freewheeling valve .............................................................27
Table of Contents

6
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
3.4-6 Emergency-lowering system ......................................................27
3.4-7 Fall-protection anchorage ........................................................28
3.4-8 Platform load-sensing system .....................................................28
3.4-9 Maintenance support ...........................................................29
3.4-10 Propane cylinder (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.4-11 Auto-level system (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.5 General components ...............................................................29
3.5-1 AC power socket on the platform ..................................................29
3.5-2 Folding guardrail system .........................................................29
3.5-3 Extension platform ..............................................................30
3.5-4 Motion alarm ..................................................................30
3.6 Optional equipment ................................................................30
3.6-1 Secondary Guarding Lift Enable (SGLE) push-button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.6-2 Elevate™ telematics - access control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.6-3 Outrigger/generator control console ...............................................32
3.6-4 Hydraulic generator ............................................................33
Section 4 – Inspections Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1 Operator’s Responsibility ...........................................................35
4.2 Visual and daily maintenance inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2-1 Labels .......................................................................36
4.2-2 Electrical .....................................................................36
4.2-3 Hydraulic .....................................................................36
4.2-4 Base ........................................................................37
4.2-5 Wheels/Tires ..................................................................37
4.2-6 Engine compartment ............................................................38
4.2-7 Hydraulic compartment ..........................................................40
4.2-8 Platform assembly ..............................................................41
4.2-9 Lift mechanism ................................................................42
4.3 Function Tests ....................................................................43
4.3-1 Do a test of the main power disconnect switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3-2 Do a test of the emergency-stop button on the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3-3 Do a test of the load-sensing module self-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3-4 Do a test of the idle/platform/base key switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3-5 Do a test of the emergency-lowering function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3-6 Do a test of the positive air shutoff (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.3-7 Do a test of the platform emergency-stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.3-8 Do a test of the function-enable switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.3-9 Do a test of the steer function .....................................................46
4.3-10 Do a test of the drive function .....................................................47
4.3-11 Do a test of the anti-tiedown function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.3-12 Do a test of the brakes ..........................................................47
4.3-13 Do a test of the platform raise and lower functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.3-14 Do a test of the horn ............................................................48

7
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
4.3-15 Do a test of the elevated travel speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.3-16 Do a test of the SGLE switch (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.3-17 Do a test of the outrigger interlocks (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.3-18 Do a test of the auto-level (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.3-19 Do a test of the generator (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.4 Operator’s Checklist ...............................................................53
Section 5 – Operation ......................................................55
5.1 Energize the base control console ....................................................55
5.2 Raise or lower the platform with the base control console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
5.3 Energize the platform control console .................................................56
5.4 Raise or lower the platform with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
5.5 Drive forward or rearward ...........................................................57
5.6 Steer ............................................................................57
5.7 Select the level-drive or inclined-drive mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
5.8 Extend/retract the extension platform .................................................58
5.9 Use the auto-level (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
5.10 Start and stop the generator (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
5.11 Raise and lower with the SGLE platform control console (optional equipment) . . . . . . . . . . . . . . .59
5.12 MEWP shutdown ..................................................................60
Section 6 – Additional Procedures ...........................................61
6.1 Use the emergency-lowering function .................................................61
6.2 Release the brakes manually ........................................................62
6.3 Winch and tow the MEWP ...........................................................62
6.4 Move the MEWP for transport ........................................................63
6.4-1 Lift the MEWP with a forklift .......................................................63
6.4-2 Hoist the MEWP ...............................................................64
6.4-3 Drive and tie-down the MEWP ....................................................65
6.5 Use the platform control console from the ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
6.5-1 Disconnect and remove the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.5-2 Operate the MEWP from the ground ................................................66
6.6 Fold the guardrails ................................................................68
6.6-1 Fold the guardrail system down ...................................................68
6.6-2 Unfold the guardrail system up ....................................................70
6.7 Move the MEWP through a doorway ..................................................71
6.8 Use the maintenance support ........................................................73
6.8-1 Deploy the maintenance support ..................................................73
6.8-2 Store the maintenance support ....................................................73
6.9 Refuel ...........................................................................74
6.9-1 Refuel the MEWP with gasoline or diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.9-2 Replace the propane cylinder (dual fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.9-3 Remove the propane cylinder .....................................................75
6.9-4 Install the propane cylinder .......................................................75

8
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Section 7 – Technical Specifications ..........................................77
7.1 Standard and optional equipment ....................................................77
7.2 Owner’s annual inspection record ....................................................78
7.3 Specifications ....................................................................79
7.4 Maximum platform capacities (evenly distributed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
7.5 Environment ......................................................................80
7.6 Floor loading pressure .............................................................81
Section 8 – Labels ........................................................83
8.1 Engine compartment ...............................................................84
8.2 Right side ........................................................................86
8.3 Front side ........................................................................89
8.4 Left side .........................................................................91
8.5 Hydraulic/fuel compartment .........................................................95
8.6 Rear side ........................................................................96
8.7 Propane tank .....................................................................98
8.8 Platform view .....................................................................99
8.9 Platform control console ...........................................................101
8.10 Lift cylinders ....................................................................102
8.11 Outriggers (optional equipment) ....................................................103
8.12 Outrigger and generator control console (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
8.13 Air supply options (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Section 9 – Unique Skyjack Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

9
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Section 1 – About this Mobile Elevating
Work Platform (MEWP)
1.1 Read and heed
Skyjack is continuously improving and expanding
product features on its equipment; therefore,
specifications and dimensions are subject to change
without notice.
1.1-1 Mobile Elevating Work Platform
(MEWP) definition
A MEWP is a mobile machine intended for moving
persons, tools, and material to working positions. It
consists of a work platform with controls, an extending
structure, and a chassis.
1.1-2 Purpose of equipment
The Skyjack Rough Terrain Scissor lifts are designed
to move personnel, tools, and materials to working
positions.
1.1-3 Use of equipment
The MEWP is a highly maneuverable, mobile work
station. Only elevate the platform, or drive while
elevated on a firm, level surface.
1.1-4 Operation manual
The operation manual is an essential part of the
MEWP. It is important to always keep a copy of this
manual in the weather-resistant manual storage box of
the MEWP. The manual must be in good condition.
1.1-5 Operator
Before the operator operates the MEWP, they must
read and completely understand this information:
1. The full contents of the operation manual,
including the operating procedures, the MEWP
limitations, the responsibilities of the operator for
the operation, applicable maintenance, warnings
and safety instructions.
2. The safety panel label on the platform, the labels
on the MEWP and the attachments.
Compare the labels on the MEWP with the labels in
this manual. Immediately replace any labels that are
damaged or missing.
Only trained and authorized personnel are permitted
to operate a MEWP.
The operator must be familiar with the employer’s
work rules and related government regulations.
1.1-6 Service policy and warranty
Skyjack warrants each new product to be free of
defective parts and workmanship for the first 2 years
or 3000 hours, whichever occurs first. Your local
Skyjack dealer will replace or repair any defective
part, with no charge for parts or labour. In addition, all
products have a 5-year structural warranty. Contact
the Skyjack service department for warranty statement
extensions or exclusions.
1.1-7 Ownership of MEWP
Notify Skyjack of MEWP ownership. If you sell or
transfer the ownership of a MEWP, promptly notify
Skyjack of the new owner’s contact information.
Skyjack needs this information to inform the owner of
any updates or additional activities that are necessary
to keep the machine in proper working condition.
1.1-8 Optional equipment
This MEWP accepts a variety of optional equipment.
Refer to section 7.1 for a list of the optional
accessories. Section 5 contains operating instructions
for these options.
For components or systems that are not standard,
speak to the Skyjack Service Department. Give the
model and serial number for each applicable MEWP.

10
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Section 1 – About this Mobile Elevating Work Platform (MEWP) Read and heed
1.1-9 Scope of this manual
1. This manual applies to the ANSI/CSA versions of
the SJ Rough Terrain Scissor Lift series. For a list
of applicable models, refer to section 7.1.
▪Equipment identified with ANSI meets the
ANSI SAIA-A92.20-2018 standard.
▪Equipment identified with CSA meets the CSA
B354.6:2017 standard.

11
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Primary assemblies Section 1 – About this Mobile Elevating Work Platform (MEWP)
1.2 Primary assemblies
The MEWP has these primary assemblies:
1. Base
2. Lift mechanism
3. Platform.
1 Base: The base is an assembly consisting of
these parts:
The base has these parts:
▪A compartment attached to the right side of
the base which contains The compartment
contains these parts:
▪Base control console
▪Electrical panel
▪Engine
▪12V starter battery
▪A compartment attached to the left side of
the base which contains The compartment
contains these parts:
▪A hydraulic tank with a sight gauge
▪A fuel tank with a fuel gauge
▪Hydraulic manifolds.
▪An emergency-lowering system.
▪A liquid propane gas (LPG) tank (optional
equipment).
▪A ladder at the rear of the base.
▪Two front and two rear outriggers (optional
equipment).
▪Two front wheels driven by hydraulic wheel
motors. The front wheels are steered by a
hydraulic cylinder.
▪Two rear wheels driven by hydraulic wheel
motors.
▪A hydraulic pump which gives power to the
hydraulic system. It is connected to the
engine.
2 Lift mechanism: The lift mechanism is a
scissor-type assembly made of formed steel or
tube sections. The scissor assembly and the
platform are raised and lowered by single-acting
hydraulic-lift cylinders with holding valves.
3 Platform: The platform has these parts:
▪A tubular support frame
▪A slip-resistant “diamond plate” deck surface
▪Hinged tubular guardrails, with mid-rails and
toe boards
▪A spring-returned gate with a latch
▪A front extension platform
▪A platform control console
▪An AC power outlet.
3
2
1

12
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Section 1 – About this Mobile Elevating Work Platform (MEWP) Serial number nameplate
1.3 Serial number nameplate
The serial number nameplate 1 is located on the
side of the MEWP. It contains this information:
▪Model number
▪Type
▪Group
▪Serial number
▪Indoor or outdoor use
▪Capacity and maximum number of persons
▪Voltage
▪Maximum drive height
▪Maximum platform height
▪Maximum wind speed
▪Maximum manual force
▪Model year
▪MEWP weight
▪System pressure
▪Maximum incline.
1

13
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Maintenance responsibility Section 1 – About this Mobile Elevating Work Platform (MEWP)
1.4 Maintenance responsibility
1.4-1 Operator
Before each shift starts, do all the daily inspections
and function tests. Refer to section 4.
1.4-2 Maintenance and inspection
schedule
Refer to the service manual for frequent, periodic, and
annual inspections.
The actual operating environment of the MEWP may
affect the maintenance schedule.
IMPORTANT
Only use original or manufacturer-approved parts
and components for the MEWP.
NOTE
Refer to the Skyjack website (www.skyjack.com) for
machine registration and latest service bulletins before
you do frequent, periodic or annual inspections.
1.4-3 Owner
The owner is responsible for the maintenance
inspections and repairs. Refer to the service manual
for the maintenance instructions, the recommended
intervals and and inspection areas. Keep a record
of the annual inspection on the label on the scissor
assembly. Refer to section 7.2 in this manual.
WARNING
Only trained and qualified/competent personnel,
who understand the mechanical procedures, may
do maintenance on the MEWP. The use of a MEWP
that is not properly maintained or in the correct
working condition could result in death or serious
injury.

14
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Notes

15
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Section 2 – General Safety Precautions
WARNING
Failure to obey the instructions and precautions
in this manual could result in MEWP damage,
property damage, personal injury, or death.
It is mandatory that you use this MEWP correctly.
Read this manual and make sure you fully understand
it before you operate the MEWP.
Use personal protective equipment (PPE) to protect
your eyes, ears, hands, feet, and body when you do
work on or near machinery.
Any modifications to the MEWP must have written
permission from Skyjack.
WARNING
Do not operate the MEWP if:
▪It does not operate correctly
▪It is damaged or shows worn or missing parts
▪The safety devices are tampered with or
disabled
▪It is locked and tagged for servicing or repair
▪It was modified without permission from
Skyjack and the MEWP owner.
If you do not obey, there is a risk of death or
serious injury.
2.1 Electrocution hazards
The MEWP is not electrically insulated and does not
provide protection from contact with or proximity to
energized electrical conductors. Follow section 2.1-1
for the minimum distance to keep between all parts
of the MEWP, occupants, or tools, and the electrical
conductors. Consider MEWP movement and electrical
line sway in minimum distance calculation.
If you need to work nearer than 3 m (10ft), stop and
apply control measures as determined by a qualified
person with respect to electrical transmission and
distribution.
Obey all the national, state/provincial/territorial and
local safety rules.
2.1-1 Minimum distance from electrical
conductors
Voltage Range
Minimum Distance
from Electrical
Conductors
≤ 50 KVA 3 m (10 ft)
> 50 KVA, or if not known
STOP and apply control
measures as determined by a
qualified person with respect
to electrical transmission and
distribution.
DANGER
Electrocution hazard. Keep all parts of the
MEWP, occupants, or tools a safe distance away
from power lines, electrical power sources, or
energized sources. If you do not obey, there is a
risk of death or serious injury.
Keep a minimum safe distance
from sources of high-voltage
power.
DO NOT operate the MEWP
during lightning or storms.
CAUTION
DO NOT use the MEWP as a ground for welding.
If you do not obey, there is a risk of minor or
moderate injury, or malfunction or damage to the
MEWP.

16
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Section 2 – General Safety Precautions Safety instructions
2.2 Safety instructions
WARNING
DO NOT operate this MEWP without proper
authorization and training. Failure to avoid this
hazard could result in death or serious injury.
WARNING
DO NOT operate this MEWP in enclosed areas
without sufficient ventilation for exhaust gas and
fumes. If you do not obey, there is a risk of death
or serious injury.
WARNING
Failure to heed the following safety precautions
could result in tip-over, falling, crushing, or other
hazards leading to death or serious injury.
KNOW all national, state/provincial or territorial, and
local rules which apply to your MEWP and worksite.
MAKE SURE all the safety and instructional labels
are correctly attached on the MEWP in the correct
location. Clean or replace labels that you cannot read.
PREVENT unauthorized use. Disconnect and
lock out main power disconnect on the left side of
the MEWP when leaving the MEWP unattended.
DO NOT wear jewelry or loose
clothing that could become
caught or entangled.
DO NOT allow the
entanglement of ropes, cables
or hoses with the MEWP,
adjacent structures or objects.
Prevent falls from the platform.
Always keep a firm footing
on the platform floor when
working thereon. Do not climb
on the toe-board, mid-rail, or
top-rail. Do not use planks,
ladders, or any other devices
on the platform for achieving
additional height or reach.
DO NOT raise the platform or
operate elevated in windy or
gusty conditions that exceed
the limits specified in
section 7.4.
DO NOT increase the surface
area of the platform or carry
large surface area items when
exposed to wind. Increasing the
area exposed to the wind will
decrease the MEWP stability.
DO NOT elevate or drive
elevated on a slope. Elevated
driving must be done on a firm,
level surface.
DO NOT drive elevated on a
soft or uneven surface.
DO NOT raise the platform if it
is not on a firm, level surface.
MAKE SURE the ground condition assessment
considers the subsurface voids such as cellars,
basements, culverts, and pipes.

17
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Safety instructions Section 2 – General Safety Precautions
DO NOT drive elevated near
depressions or holes of any
type, loading docks, debris,
drop-offs or surfaces that may
affect the stability of the MEWP.
IF OPERATION IN AREAS
WITH HOLES OR DROP-OFFS
IS ABSOLUTELY NECESSARY,
elevated driving shall not be
allowed. Position the MEWP
horizontally only with the
platform fully-lowered. After
ensuring that all 4 wheels or
outriggers (optional equipment)
have contact with a firm, level
surface, the platform can be
raised. After elevation, the drive
function must not be activated.
DO NOT ascend or descend grades greater
than the maximum inclines listed in section 7.3.
Ascending or descending slopes must only be
done when fully lowered.
DO NOT operate a MEWP that
has ladders, scaffolding, or
other devices on it to increase
the platform size or work height.
DO NOT exceed the maximum
side force shown on the
capacity label when the platform
is elevated. Refer to section 7.4.
DO NOT use the MEWP as a
crane.
DO NOT sit, stand, or climb on
the guardrails.
DO NOT climb on the scissor
arm assembly.
DO NOT collide or crush.
Be aware of obstructions,
personnel, or other possible
hazards around the MEWP
when elevating, lowering, or
driving. Keep all body parts
inside the platform when
elevating or driving. Be aware
of blind spots when operating
the MEWP.
DO NOT elevate the platform
when the MEWP is on a truck,
forklift, or other device or
vehicle.
DO NOT use the MEWP
when the wheels or tires are
damaged. Make sure the wheel
nuts are tight. Refer to section
4.2-5.

18
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Section 2 – General Safety Precautions Safety instructions
DO NOT alter or disable
limit switches or other safety
devices.
DO NOT use the MEWP without
guardrails, locking pins, and the
entry gate(s) in place.
DO NOT use the MEWP under
the influence of alcohol or
drugs, or if the operator’s
performance is impaired by a
medical condition, the influence
of prescription or over-the-
counter drugs, or fatigue.
DO NOT exceed the rated
capacity of the MEWP.
DO NOT distribute the load
unevenly.
DO NOT use the MEWP if it
does not function correctly or if
any parts are damaged or worn.
DO NOT leave the MEWP
unattended with the key in the
key switch.
DO NOT operate on slippery surfaces without
sufficient traction to stop, drive, or steer the MEWP.
STUNT driving and horseplay are prohibited.
DO NOT position the MEWP against another
object to steady the platform.
DO NOT place materials on the guardrails
or materials that exceed the confines of the
guardrails unless approved by Skyjack.
Remove all personnel from the platform before
you try to free a snagged platform with the base
controls.

19
SJ6826 RT, SJ6832 RT 221587ACA 221587ACA
Fall-protection Section 2 – General Safety Precautions
2.3 Fall-protection
The guardrail system is the primary fall-protection
system of the MEWP platform.
If personal fall-protection equipment (PFPE) is
required, by an employer or the authority having
jurisdiction, Skyjack recommends the use of a full
body harness with a lanyard. PFPE must be attached
only to approved fall-protection anchorage points in
the platform.
All PFPE must be compliant with applicable
government rules and must be inspected as per the
manufacturer’s recommendation.
Use the three points of contact principle when you
enter or exit the platform. This is when two hands and
one foot, or one hand and two feet are in contact with
the MEWP or the ground at all times.
WARNING
Fall hazard.
▪Only enter and exit the MEWP using the three
points of contact principle.
▪Only use the equipped access openings.
▪Only enter and exit the MEWP when the
platform is fully lowered.
▪Face the MEWP when entering or exiting the
platform.
Failure to follow these instructions could result in
death or serious injury.
2.4 Worksite inspection
Make sure the operating environment, ambient
temperature, Electromagnetic Compatibility (EMC),
and Hazardous Location Rating (locations with
potentially flammable gases, explosive gases or
particles) are appropriate for the MEWP specifications
(refer to section 7.5).
Be sure to follow all national, state/provincial/territorial,
and local rules that relate to operating the MEWP.
Perform a full worksite inspection before operating the
MEWP. Identify potential hazards in the area.
Be aware of moving equipment in the area. Take the
necessary precautions to prevent collisions.
It is the responsibility of the operator to perform a
worksite inspection and avoid/address the following
hazards:
▪Holes or drop-offs
▪Slopes
▪Ditches or soft fills
▪Floor obstructions, bumps, or debris
▪Overhead obstructions
▪Electrical conductors
▪Hazardous locations
▪Inadequate surface support to withstand all load
forces imposed by the MEWP (refer to
section 7.6)
▪Wind and weather conditions
▪Presence of personnel
▪Other mobile equipment
▪Traffic hazards
▪Equipment that could move and collide with the
MEWP, such as overhead cranes
▪Other possible unsafe conditions.

20
SJ6826 RT, SJ6832 RT
221587ACA
221587ACA
Notes