Smartgen HGM6100K Series User manual

HGM6100K Series
Automatic Generator Module
OPERATING MANUAL
Smartgen Electronics

Smartgen Electronic Equipment Co., Ltd
No.28 Jinsuo Road
Zhengzhou
Henan Province
P. R. China
Tel: [phone]
0086-371-67991553/67992951/67992952
0086-371-67981000(overseas)
Fax: [phone]
Web: http://www.smartgen.com.cn
http://www.smartgen.cn
Email: [e-mail]
All rights reserved. No part of this publication may be reproduced in any material
form (including photocopying or storing in any medium by electronic means or other)
without the written permission of the copyright holder.
Applications for the copyright holder‟s written permission to reproduce any part of
this publication should be addressed to Smartgen Electronics at the address
above.
Any reference to trademarked product names used within this publication is owned
by their respective companies.
Smartgen electronics reserves the right to change the contents of this document
without prior notice.
Software Version
Version
Date
Note
1.0
2009-10-10
Original release.
1.1
2010-04-07
Add a typical wiring diagram and an AUX.INPUT4 (38 Pin) and
an AUX.INPUT5 (39 Pin) and an Earth wire (40 Pin).
1.2
2010-04-20
Add a language of Spanish. Modify the panel cutout size, and
the operation temperature range.
1.4
2010-08-17
Add a configurable output item of fuel pump control and a
configurable input item of automatic inhibit start and an option
(active connecting with B+ or B-) for all input port.
1.5
2010-12-09
Add High speed control option in output ports; Add prohibit stop
when High temperature, low oil pressure in programmable
parameters; Revise range of sensor curve input.
1.6
2011-04-12
Add Russian and five programmable output port options.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 3 of 31
CONTENT
1SUMMARY.....................................................................................4
2PERFORMANCE AND CHARACTERISTICS...............................4
3SPECIFICATION............................................................................6
4OPERATION ..................................................................................7
4.1 KEY FUNCTION......................................................................................7
4.2 AUTOMATIC OPERATION......................................................................7
4.3 MANUAL OPERATION............................................................................9
5PROTECTION................................................................................9
5.1 WARNING...............................................................................................9
5.2 SHUTDOWN ALARM ............................................................................10
6CONNECTING TERMINAL..........................................................11
7PARAMETER RANGE AND DEFINE..........................................14
7.1 PARAMETERS TABLE (TABLE 1).........................................................14
7.2 PROGRAMMABLE OUTPUT 1-4 TABLE (TABLE 2).............................19
7.3 PROGRAMMABLE DIGIT INPUT 1-5 TABLE (ALL IS VALID WHEN
CONNECT GRAND (B-) (TABLE 3)..............................................................21
7.4 SENSOR SELECTION (TABLE 4).........................................................22
7.5 CONDITIONS OF CRANK SUCCEED (TABLE 5).................................23
8PARAMETER SETTING..............................................................24
9SENSOR SELECTION ................................................................25
10 COMMISSIONING.......................................................................26
11 TYPICALAPPLICATION..............................................................27
12 INSTALLATION............................................................................29
13 FAULT FINDING...........................................................................30

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 4 of 31
1 SUMMARY
HGM6100K series Genset controller integrating digital, intelligent and network
techniques is used for automatic control system of diesel generator. It can carry
out functions including automatic start/stop, data measure and alarm protective.
The controller uses LCD display, optional Chinese, English, Spanish and Russian
display interface with operation easy and reliable.
HGM6100K series Genset controller uses micro-processing technique which can
carry out precision measure, constant value adjustment, timing and threshold
setting and etc. functions. It can be widely used in all types of generator automatic
control system for compact structure, advanced circuits, simple connections and
high reliability, can be widely applied to various types of generating units
automation system.
2 PERFORMANCE AND CHARACTERISTICS
■HGM6100K controller has four types:
HGM6110K/6110KC: Automatic Start Module, it controls generator to start/stop
by remote start signal;
HGM6120K/6120KC: Based on HGM6110K/6110KC and add mains AC
monitoring, Mains/Generator automatic switching control functions (AMF),
especially suitable for the automation system composed by Mains and Generator.
Note1: HGM6110KC/6120KC with RS485 interface, HGM6110K/6120K without RS485 interface.
Note2: And then take HGM6110KC/6120KC with text as an example to describe.
■Using microprocessor as a core, symbol LCD with backlight display, the three
languages display Chinese, English and Spanish, key touch operation;
■Have a RS485 port with Modus communication protocol;
■Adapt to 3phase-4wires, single phase-2wires or 2phase-3 wires (120/240V) ,
50/60Hz AC power system;
■Measure and display 3 phase voltage, 3 phase current, frequency, power etc.
parameter of Mains and Gens;
Mains Gens
Line voltage (Uab, Ubc, and Uca) Line voltage (Uab, Ubc, and Uca)
Phase voltage (Ua, Ub, and Uc) Phase voltage (Ua, Ub, and Uc)
Frequency HZ Frequency HZ

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 5 of 31
Load
Power Current IA, IB, IC
Active power KW
Inactive power KVar
Apparent power KVA
Power factor Cos
Accumulate total gens power kWh
■Mains have over voltage, under voltage, loss phase function; Gens have over
voltage, under voltage, over frequency, under frequency, over current function;
■Precision measure and display parameters about Engine,
Temp. (WT), °C/ °F both are display
Oil pressure (OP), kPa/Psi/Bar all be display
Fuel oil level (FL), % (unit)
Speed (SPD), RPM (unit)
Voltage of Battery (VB) V (unit)
Voltage of Charger (VD) V (unit)
Hour count (HC) can accumulate Max. 999999 hours.
Starting up can accumulate Max.999999 times.
■Control protection: Automatic crank/stop of diesel engine, load transfer(ATS
control) and completely faults display protection;
■With ETS, idle control, pre-heat control, raises speed control functions, and all
types of them are belong to relay output;
■Parameters setting: Allow user to modify setting and store them by inside
internal FLASH memory, the parameters can not be lost even with power off. All
of parameters can be set not only from the front panel, but by PC via SG72 (an
adaptor, USB-LINK-RS485) module; or, through RS485 port via PC;
■Most of temperature, pressure, oil level sensor can be directly used, and also
user can define sensor curve by themselves;
■Multiple crank disconnection conditions can be selected.(Speed sensor, oil
pressure, gens);
■Power supply range is wide(8~35)VDC, accommodating to different starting
battery voltage environments;
■All parameters use digital modulation, abandoning analog modulation using
conventional electronic potentiometer, more reliability and stability;
■Modular configuration design, Flame Retardant ABS plastic shell, inserted type

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 6 of 31
connection terminals, flush type installation, compact structure, easy
installation.
3 SPECIFICATION
Operating Voltage
DC8.0V to 35.0V, Continuous
Power Consumption
<3W(Standby mode: ≤2W)
AC voltage Input Range
3-Phase 4 Wire
2-Phase 3 Wire
Single phase 2 Wire
15V AC - 360 V AC (ph-N)
15V AC - 360 V AC (ph-N)
15V AC - 360 V AC (ph-N)
Frequency
50Hz - 60 Hz
Magnetic AC voltage
1.0V to 24V (effective value)
Magnetic AC Frequency
10,000 Hz (max)
Start Relay Output
16 Amp DC28V at supply voltage.
Fuel Relay Output
16 Amp DC28V at supply voltage.
Auxiliary Relay Output 1
7 Amp DC28V
Auxiliary Relay Output 2
7A 250VAC passive
Auxiliary Relay Output 3
16A 250VAC passive
Auxiliary Relay Output 4
16A 250VAC passive
Overall Dimensions
209mm x 153mm x 55mm
Panel cutoff
186mm x 141mm
C.T. Secondary
5A (rated )
Operating Temp. Range
Temperature: (-25~70)ºC; Humidity: (20~90)%
Storage Condition
Temperature: (-30~+80)ºC
Protective Level
IP55: when waterproof rubber ring added between
controller and its panel.
IP42: when waterproof rubber ring not have
between controller and its panel.
Insulation Intensity
Object: among in input/output/power
Quote standard: IEC688-1992
Test way: AC1.5 kV / 1min 3mA leakage current
Weight
0.71kg

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 7 of 31
4 OPERATION
4.1 KEY FUNCTION
Stop/ Reset
Can stop generator under mode of Manual/Auto;
Can reset alarming under Stop;
To test panel indicators are OK or not, pressing this
key at least 3 seconds;
During stopping process, press this again can stop
generator immediately.
Start
To start genset under Manual or Auto mode.
Manual
Pressing this key will set the module into manual
mode.
Automatic
Pressing this key will set the module into automatic
mode.
Running with load
Pressing and controller is under manual testing
mode.
Under this mode, genset will run with load automatic
when gens are normal. (HGM6110KC without)
Set/ Confirm
Enters into Set menu after pressing this, and can shift
cursor to confirm.
Page up
/increase
Screen pages turning;
Shift cursor and increase its position no. in setting.
Page down
/decrease
Screen pages turning;
Shift cursor and decrease its position no. in setting.
4.2 AUTOMATIC OPERATION
This mode is activated by pressing the . LED indicator is illuminating beside the
button confirms this action.
Sequence of Auto Start,
a) HGM6120KC, When Mains is abnormal (over and under voltage, or miss
phase), enters into mains “abnormal delay”and LCD display count down time.
When mains abnormal delay is over, enter into “start delay”.
b) HGM6110KC, entries into “start delay”as soon as “Remote Start”is input valid.
c) “Count down”of start delay is displayed in LCD.
d) When start delay is over, preheat relay is outputting (if be equipped), “preheat
start delay XX s”is displayed in LCD.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 8 of 31
e) When preheat relay is over, oil relay is outputting 1s and then start relay-output;
if genset fails in starting during “cranking time”, the oil and start relays stop
outputting and enters into “crank rest time”and wait for next attempt.
f) If genset fails in starting within setting attempt times, thefourth line of LED willin
black and start failed alarm will be displayed on it.
g) Whatever times to start genset successfully, it will enter into “safety on time”.
During this period, alarms of low oil pressure, hi-temperature, under speed,
charge fail and Aux. input (been configured) are inactive. As soon as this delay
is over, genset will enter into “start idle delay”(if this be configured).
h) During “start idle delay”, alarms of under speed, under frequency, under voltage
are inactive. As soon as this delay is over, genset will enter into “warming up
time delay”(if this be configured).
i) When “warming up time delay”is over, gens status indicator is light if gens
normal. If alternator‟s voltage, frequency meets to requirement of load, gens will
close and relay is outputting., then genset will enter into normal running with
load and gens indicator is light; if genset voltage and frequency is abnormal,
controller will alarm and stop engine (gens alarming is displayed LCD).
Sequence of Auto Stop,
a) HGM6120KC, When Mains recovery during genset running, enters into mains
voltage “normal delay”and its indicator light after Mains normal be confirmed.
“Start delay”is beginning.
b) HGM6110KC, genset enters into “stop delay”as soon as “Remote Start”putting
is inactive.
c) As soon as “stop delay”is over, genset enters into “High Speed cooling delay”.
Mains are close and breaker is disconnected. After switch “rest time delay”,
mains are close and relay is output as well as with loading. Gens‟indicator is
dark while mains‟light.
d) Idle relay has power and outputs as soon as entering “stop idle relay” (If this
been configured).
e) When enters “ETS relay”, ETS relay has power and outputs. Oil relay‟s output is
disconnected.
f) When genset enters “stop time”, automatic to decide whether generator is
stopped or not.
g) When genset will enter into “over stop time”as soon as genset is stopped. If
genset failed to stop and controller will alarm (“stop failed” will be displayed in
LCD).

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 9 of 31
4.3 MANUAL OPERATION
1) HGM6120KC, Auto starts mode is active when press and its indicator is
illuminating. Press , then controller under “Manual Test Mode”and its
indicator is illuminating. Under the both modes, press to start genset, and
it can automatic detect start successfully and accelerate to Hi-speed running. If
there is Hi-temperature, low oil level and voltage abnormal during diesel genset
running, controller can protect genset to stop quickly (detail procedures please
refer to No.4~9 of Auto start operation). Under “Manual Test Mode “,
genset with load is decided by Mains is normal or not. If mains are normal,
loading switch is never transferred; while mains are abnormal, loading switch is
transferred into gens side. Under “Manual Test Mode “, after genset runs
well in high speed, no matter mains is normal or not, loading switch must be
transferred into gens side.
2) HGM6110KC, Auto starts mode is active when press , and its indicator is
illuminating. Then press to start generator, it can automatic detect start
successfully and genset automatic accelerates to Hi-speed running. If there is
Hi-temperature, low oil level and voltage abnormal during diesel genset running,
controller can protect genset to stop quickly (detail procedures please refer to
No.4~9 of Auto start operation). After genset runs well in High speed, controller
will send signal of gens close.
3) Manual stop, press can shut down the running genset (detail procedures
please refer to No.3~7 of Auto stop operation).
5 PROTECTION
5.1 WARNING
When controller detects the warning signal, only alarm and not stop genset. The
alarms are displayed in LCD.
Warnings as following,
No.
Type
Description
1
Lost of speed
When controller detected the speed of genset is 0 and
speed lost delay set as 0, controller will send warning
alarm signal and it will be displayed in LCD

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 10 of 31
No.
Type
Description
2
Gens Over
Current
When controller detected the current of genset is over
than threshold and over current delay set as 0,
controller will send warning alarm signal and it will be
displayed in LCD
3
Failed To Stop
When generator not stops after the “stop relay”is over,
controller will send warning alarm signal and it will be
displayed in LCD
4
Low oil level
When controller detected the oil level of genset is lower
than threshold or low oil level warn input is active,
controller will send warning alarm signal and it will be
displayed in LCD
5
Charge Alt Fail
When controller detected the voltage of genset charger
is lower than threshold, controller will send warning
alarm signal and it will be displayed in LCD
6
Battery Low
Voltage
When controller detected the voltage of genset battery
is lower than threshold, controller will send warning
alarm signal and it will be displayed in LCD
7
Battery High
Voltage
When controller detected the voltage of genset battery
is higher than threshold, controller will send warning
alarm signal and it will be displayed in LCD
8
Low water level
When controller detected the warning of low water level
input is active, controller will send warning alarm signal
and it will be displayed in LCD
5.2 SHUTDOWN ALARM
When controller detected shutdown alarm, it will send signal to break off and to stop.
The alarms are displayed in LCD.
Stop alarms as following,
No.
Type
Description
1
Emergency Stop
When controller detected emergency stop signal, it will
send a stop alarm signal and it will be displayed in LCD
2
High Temp
alarm
When controller detected the temperature of
water/cylinder is higher than set, it will send a stop
alarm signal and it will be displayed in LCD
3
Lower OP
alarm
When controller detected oil pressure is lower than set
for alarming, it will send a stop alarm signal and it will
be displayed in LCD
4
Over speed
alarm
When controller detected genset speed is over than set
for alarming, it will send a stop alarm signal and it will
be displayed in LCD
5
Under speed
When controller detected genset speed is under than

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 11 of 31
No.
Type
Description
alarm
set for alarming, it will send a stop alarm signal and it
will be displayed in LCD
6
Speed signal
lost alarm
When controller detected genset speed is 0 or delay is
not 0, it will send a stop alarm signal and it will be
displayed in LCD
7
Gens over
voltage
When controller detected genset voltage is over than
set for alarming, it will send a stop alarm signal and it
will be displayed in LCD
8
Gens under
voltage
When controller detected genset voltage is under
than set for alarming, it will send a stop alarm signal
and it will be displayed in LCD
9
Gens over
current
When controller detected genset current is over than
set for alarming or delay is not 0, it will send a stop
alarm signal and it will be displayed in LCD
10
Start failed
alarm
During the start attempt times, if genset start failed, it
will send a stop alarm signal and it will be displayed in
LCD
11
Over frequency
alarm
When controller detected genset frequency is over than
set for alarming, it will send a stop alarm signal and it
will be displayed in LCD
12
Under
frequency alarm
When controller detected genset frequency is under
than set for alarming, it will send a stop alarm signal
and it will be displayed in LCD
13
Gens failed
alarm
When controller detected genset frequency is 0, it will
send a stop alarm signal and it will be displayed in LCD
14
Oil level lower
alarm
When controller detected genset oil lever lower input is
active, it will send a stop alarm signal and it will be
displayed in LCD
15
Water level
lower alarm
When controller detected genset water level lower input
is active, it will send a stop alarm signal and it will be
displayed in LCD
6 Connecting terminal
HGM6110KC compared with HGM6120KC, is less a Mains three phase AC input
terminal. The HGM6110KC and HGM6120KC backplane is as following.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 12 of 31
Description of terminal blocks connection
Pin
Function
Dim
Description
1
DC Plant Supply input
(-ve)
2.5mm
System DC negative input. (Battery
Negative).
2
DC Plant Supply input
(+ve)
2.5mm
System DC positive input. (Battery
Positive). (Recommended Maximum
Fuse 20A)
3
Emergency stop input
2.5mm
Plant Supply +ve. Also supplies fuel &
start outputs.
4
Fuel relay output
1.5mm
Plant Supply +ve from pin 3.
16 Amp rated.
5
Start relay output
1.5mm
Plant supply +ve
from pin 3. 16 Amp
rated.
Connect to
starter starting
coil
6
Auxiliary relay output 1
1.5mm
Plant Supply +ve
from pin 2. 7 Amp
rated.
Reference
table 2
7
Auxiliary relay output 2
1.5mm
Closed output, 7
Amp rated.
8
Relay common point
9
Open output,7 Amp
rated.
10
Auxiliary relay output 3
2.5mm
Free volt contacts.
16 Amp rated
11
12
Auxiliary relay output 4
2.5mm
13
14
Charge Gens D+ port
1.0mm
Do not connect to ground (battery –ve)

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 13 of 31
Pin
Function
Dim
Description
input
15
Magnetic pickup +ve
Connect to Magnetic Pickup device.
16
Magnetic pickup -ve
17
Temp. sensor input
Connecting water/cylinder
temperature resistance type
sensor.
Reference
table 4
18
Oil pressure input
Connect to oil pressure sensor.
19
Liquid level input
Connect to liquid Level sensor.
20
Auxiliary input 1
1.0mm
Switch to -ve
Reference
table 3
21
Auxiliary input 2
1.0mm
Switch to -ve
22
Auxiliary input 3
1.0mm
Switch to -ve
23
CT Secondary for A
1.5mm
Connect to secondary of A
monitoring CT
24
CT Secondary for B
1.5mm
Connect to secondary of B monitoring
CT
25
CT Secondary for C
1.5mm
Connect to secondary of C monitoring
CT
26
CT secondary common
1.5mm
Connect to secondary of all monitoring
CT‟s
27
Generator A voltage
monitoring
1.0mm
Connect to Generator A output
(Recommend 2A fuse)
28
Generator B voltage
monitoring
1.0mm
Connect to Generator B output
(Recommend 2A fuse)
29
Generator C voltage
monitoring
1.0mm
Connect to Generator C output
(Recommend 2A fuse)
30
Generator Neutral input
1.0mm
Connect to generator neutral
terminal (AC)
31
Mains A voltage
monitoring
1.0mm
Connect to mains A output
(Recommend 2A fuse)
32
Mains B voltage
monitoring
1.0mm
Connect to mains B output
(Recommend 2A fuse)
33
Mains C voltage
monitoring
1.0mm
Connect to mains C output
(Recommend 2A fuse)
34
Mains Neutral input
1.0mm
Connect to mains neutral terminal
35
RS485 port common
0.5mm
Use only 120Ω RS485 approved cable.
36
RS485 port A(-)
0.5mm
37
RS485 port B(+)
0.5mm
38
Auxiliary input 4
1.0mm
Switch to -ve
Reference
table 3
39
Auxiliary input 5
1.0mm
Switch to -ve
40
Common port
1.0mm
Auxiliary input common port
Note: LINK interface in back is as a parameter programming interface, by PC to
programmable controller via SG72 adapter.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 14 of 31
7 PARAMETER RANGE AND DEFINE
All parameters of HGM6100K series are as following:
7.1 PARAMETERS TABLE (TABLE 1)
Num
Parameter
Range
Default
Description
1
Mains volt
normal delay
(0-3600)s
10
Mains transient delay,
suited for ATS (automatic
transfer switch).
2
Mains volt
abnormal delay
(0-3600)s
5
3
Mains under volt
(30-360)V
184
When mains voltage is
under than the point,
mains under voltage are
active. When the point is
zero, mains under voltage
are disabled.
4
Mains over volt
(30-360)V
276
When mains voltage is
over than the point, mains
over voltage are active.
When the point is 360V,
mains over voltage are
disabled.
5
Transfer Switch
interval
(0-99.9)s
1.0
It‟s the delay from mains is
opened to generator
closing or from generator
is opened to mains
closing.
6
Start delay
(0-3600)s
1
It‟s the delay from remote
start signal is active or
mains is failure, to start
generator.
7
Stop delay
(0-3600)s
1
It‟s the delay from remote
start signal is inactive or
mains is normal, to stop
generator.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 15 of 31
Num
Parameter
Range
Default
Description
8
Number of crank
(1-10)times
3
When engine start no
success, most of cranking
numbers. When reach
setting crank numbers,
controller send out start fail
signal.
9
Preheat time
(0-300)s
0
10
Crank time
(3-60)s
8
The starter adds the time
of the electricity each time.
11
Crank rest time
(3-60)s
10
12
Safe run time
(1-60)s
10
13
Start idle time
(0-3600)s
0
14
Warming up time
(0-3600)s
10
15
Cooling time
(3-3600)s
10
16
Stop idle time
(0-3600)s
0
17
ETS solenoid
hold
(0-120)s
20
It‟s the delay for energizing
to stop.
18
Fail to stop delay
(0-120)s
0
19
ATS close time
(0-10)s
5.0
Mains or Generator switch
closing pulse width, when
it is zero, output is
continuous.
20
Flywheel teeth
(10-300)
118
21
Gens abnormal
delay
(0-20.0)s
10.0
22
Gens over volt
(30-360)V
264
When generator voltage is
over than the point,
generator over voltage is
active. When the point is
360V, generator over
voltage is disabled.
23
Gens under volt
(30-360)V
196
When generator voltage is
under than the point,
generator under voltage is
active. When the point is
30V, generator under
voltage is disabled.
24
Under speed
(0-6000)RPM
1200
When the engine speed is
under than the point and
hold great than 10
seconds, generator under
speed is active.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 16 of 31
Num
Parameter
Range
Default
Description
25
Over speed
(0-6000)RPM
1710
When the engine speed is
over than the point and
hold great than 2 seconds,
generator over speed is
active.
26
Gens under freq
(0-75.0)Hz
45.0
When generator freq. is
low than the point,
generator low frequency
and hold great than 10
seconds is active.
27
Gens over freq
(0-75.0)Hz
57.0
When generator freq. is
over than the point and
hold great than 2 seconds,
generator over frequency
is active.
28
High
temperature
(80-140)°C
98
When engine temperature
sensor value is over than
this point and remain for 2
seconds, send out
shutdown alarm. When the
value is 140, send out
warning alarm. (It‟s suited
for engine temperature
sensor only).
29
Low oil pressure
(0-400)kPa
103
When engine oil pressure
sensor value is under than
this point and remain for 2
seconds, send out
shutdown alarm. When the
value is zero, send out
warning alarm. (it‟s suited
for oil pressure sensor
only)
30
Low Fuel Level
(0-100)%
10
When fuel level sensor
value is under than this
point and remain for 10
seconds, send out warning
alarm.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 17 of 31
Num
Parameter
Range
Default
Description
31
Lose speed
delay
(0-20.0)s
5.0
When speed is zero and
remain for the delay, send
out shutdown alarm. When
the delay is zero, send out
warning alarm.
32
Charge fail volt
(0-30)V
6.0
During generator is
running, when charge
alternator WL/D+ voltage
is under than this point and
remain for 5 seconds,
generator will warning
alarm.
33
Battery over volt
(12-40)V
33.0
When generator battery
voltage is over than the
point and hold for 20
seconds, battery over
voltage signal is active. It‟s
a warning alarm.
34
Battery under
volt
(4-30)V
8.0
When generator battery
voltage is under than the
point and hold for 20
seconds, battery under
voltage signal is active. It‟s
a warning alarm.
35
CT rate
(5-6000)/5
500
Current transformer rate
36
Full load current
(5-6000)A
500
Mains or generator set
maximum rated current.
37
Over current
percentage
(50-130)%
120
When the load current is
over than the point, the
over current delay is
initiated.
38
Over current
delay
(0-3600)s
1296
When load current is over
than the point and hold
great than the timer, send
out over current signal.
When the delay is zero,
over current is disabled.
39
Open Fuel
Pump threshold
(0-100)%
25
When the fuel level lower
than the set value and for
10 seconds, the output
signal to open fuel pump.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 18 of 31
Num
Parameter
Range
Default
Description
40
Fuel pump off
threshold
(0-100)%
80
When the fuel level higher
than the set value and for
10 seconds, the output fuel
pump off signal.
41
Digit Output1 set
(0-17)
2
Energized to stop
42
Digit Output 2
set
(0-17)
3
Idle control
43
Digit Output 3
set
(0-17)
5
Close gens
44
Digit Output 4
set
(0-17)
6
Close mains
45
Aux. input1
(0-15)
1
High Temperature input
46
Aux. input1 valid
(0-1)
0
Factory default is: closed
47
Aux. input1
delay
(0-20.0)s
2.0
48
Aux. input2
(0-15)
2
Low Oil Pressure input
49
Aux. input2 valid
(0-1)
0
Factory default is: closed
50
Aux. input2
delay
(0-20.0)s
2.0
51
Aux. input3
(0-15)
10
Remote start input
52
Aux. input3 valid
(0-1)
0
Factory default is: closed
53
Aux. input3
delay
(0-20.0)s
2.0
54
Aux. input4
(0-15)
11
Low fuel level warn
55
Aux. input4 valid
(0-1)
0
Factory default is: closed
56
Aux. input4
delay
(0-20.0)s
2.0
57
Aux. input5
(0-15)
12
Low coolant level warn
58
Aux. input5 valid
(0-1)
0
Factory default is: closed
59
Aux. input5
delay
(0-20.0)s
2.0
60
Module power
on
(0-2)
0
0: Stop mode
1: Manual mode
2: Auto mode
61
Module address
(1-254)
1
62
Passwords set
(0-9999)
1234
63
Crank success
condition select
(0-5)
2
Setting item is given in
Table 5.
64
Speed
disconnect
(0-3000)RPM
360
When engine speed is
over than this point, starter
will disconnect.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 19 of 31
Num
Parameter
Range
Default
Description
65
Freq disconnect
(10-30)Hz
14
When generator frequency
is over than this point,
starter will disconnect.
66
OP disconnect
(0-400)kPa
200
When engine oil pressure
is over than this point,
starter will disconnect.
67
High temp.
prohibit select
(0-1)
0
Default, when temperature
is higher, alarm to stop.
Details see Note1.
68
Low OP prohibit
select
(0-1)
0
Default, when oil pressure
is lower, alarm to stop.
Details see Note2.
69
Single/3 phases
input select
0
3phase-4wire
1
2phase-3wire
2
1phase-2wire
0
3phase-4wire
70
Select temp.
sensor
(0-9)
08
SGX
71
Select press
sensor
(0-9)
08
SGX
72
Select liquid
level sensor
(0-5)
03
SGD
Note 1, if set as higher temperature to prohibit stop, or set programmable port as
higher temperature prohibits stop and this port is active, when temperature value
is higher than set of higher temperature value or higher temperature alarm input is
active, controller send warning signal of higher temperature only and not stop.
Note 2, if set as lower oil pressure to prohibit stop, or set programmable port as
lower oil pressure prohibits stop and this port is active, when lower oil pressure
value is lower than set of lower oil pressure value or lower oil pressure alarm input
is active, controller send warning signal of higher temperature only and not stop.
7.2 PROGRAMMABLE OUTPUT 1-4 TABLE (TABLE 2)
Num
Content
Description
0
Not used
Output is no use when select this
1
Common alarm
The designated programmable output relay
will energize when any warning or shutdown
fault circuit has been activated.

HGM6100K Series Automatic Generator Module
HGM6100K Series Automatic Generator Module ISSUE 2011-04-12 Version 1.6 Page 20 of 31
Num
Content
Description
2
ETS solenoid hold
The designated programmable output relay
will energize when a stop signal has been
activated. The output will remain energized for
pre-set timer once the engine has come to a
complete stop, then de-energizes.
3
Idle control
The designated programmable output relay
will energize when the idle delay is not zero.
The output contact would typically be
connected to the “idle/run” input control of an
electronic governor.
4
Preheat control
The designated programmable output relay
will energize during the preheat delay timer
period and also energize until the engine
receive a crank success signal. The preheat
output is typically used for an engine starting
aid such as glow plugs.
5
Closed Gens
Switch generator breaker on.
6
Closed Mains
Switch mains breaker on.(HGM6120KC)
7
Open ATS
Switch breaker off. The output delay is 3
seconds.
8
Raise speed
In the process of warm-up when he entered
the suction, suck time for high-speed warm-up
delay time. Raise speed auxiliary input
effective disconnect.
9
Drop speed
Enter into stop idling process or to ETS
solenoid stop (when alarm stop) sucked, and
suck time to stop idling delay time. Drop
speed when the auxiliary active disconnect.
10
Generator run output
Outputting when genset in normal running
and disconnected after speed is lower than
start successful speed value.
11
Fuel pump control
When the fuel level lower than the set
threshold to open the fuel pump or input a low
oil level warning enter active pull; when the
fuel level over than that set off the fuel pump
and the input threshold of the low oil level
warning off when input is inactive open.
12
High speed control
Outputting when genset enters into "Warming
Up" and disconnected after "Cooling Down" is
over.
13
System in automatic
mode
The controller work in automatic mode.