SMC Networks VQ100 Series User manual

Wide variations of wiring
Single Valve Unit
Manifold
L plug connector
M plug connector
Grommet
Plug-in unit manifold
Plug lead unit manifold
Outstandingly high speed,
stable response, and long
service life.
ON: 3.5 ms, OFF: 2 ms, Dispension accuracy 앐1 ms
(With light/surge voltage suppressor; supply
pressure 0.5 MPa)
200 million cycles or more (Factors determined in a
life test by SMC)
Compact yet provides a
large flow capacity
Body width: 9.8 mm
C: 0.055 dm3/(s·bar)(Standard, high pressure type)
C: 0.14 dm3/(s·bar) (Large flow type)
: Option
Option
External non-leak
Latching
Negative COM
AC
Normally open
Vacuum
Copper-free
The fluid contacting section is copper-free and the
standard style can be used as it is.
3 Port Solenoid Valve
Series VQ100
4-12-1
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN

Manual Override Operation
If the manual override is manipulated, since any connected
equipment will be activated, make sure to be done only after no
danger is confirmed.
Non-locking push type (Tool required)
Locking type (Tool required) < Option >
Push-locking type (Tool required) < Latching type >
Note) Ensure the locking type manual override is unlocked before
using.
Attaching and detaching connectors
앬To attach a connector, hold the lever and connector unit
between your fingers and insert straight onto the pins of the
solenoid valve so that the lever’s pawl is pushed into the
groove and locks.
앬To detach a connector, remove the pawl from the groove by
pushing the lever downward with your thumb, and pull the
connector straight out.
Note) GENTLY pull the lead wire, otherwise it may cause contact failure or
disconnection.
Crimping of lead wires and sockets
Peel 3.2 to 3.7 mm of the tip of lead wire, enter the core wires
neatly into a socket and crimp it with a special crimp tool. Be
careful so that the cover of lead wire does not enter into the
crimping part. (Crimping tool part no.: DXT170-75-1)
Lead wire 0.2 to 0.33 mm2
(Max. cover diameter: ø1.7 mm)
Socket
Crimping area
Core wire
crimping area
Hook Insulation
Core wire
Attaching and detaching lead wires with sockets
앬Attaching
Insert the sockets into the square holes of the connector (with
A, C, and B indication) and continue to push the sockets all the
way in until the lock by hooking into the seats in the connector.
(When they are pushed in, their hooks open and they are
locked automatically.) Then confirm that they are locked by
pulling lightly on the lead wires.
앬Detaching
Pull and detach the lead wire, pressing in on the end of the
hook of the socket through the side hole using a stick with thin
end (about 1 mm). To reuse the socket, extend the hook
outward.
Connector
Lead wire
Socket
Hook
When operating the lock with the driver, use a watchmakers’
screwdriver and turn lightly.
[Torque 0.1 N·m or less]
Caution
Lead wire
Socket
Part no. DXT170-71-1
0.2 to 0.33 mm2
(Max. cover diameter: ø1.7 mm)
Cover
Pin
Convex
part
Convex
part
Pin Connector
Part no. AXT661-12
Lever
Hook
ON
TURN PUSH
01
OFF
TURN
01
Set
TURN PUSH
01
Reset
TURN PUSH
01
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
•It is turned ON by pushing the button in the
direction indicated by the arrow until it hits the
end and is turned OFF by releasing the button.
•If the manual override is turned clockwise and
the mark is adjusted to 1, it will be locked in
the ON state.
•If the manual override is turned,
counterclockwise and mark is adjusted to 0,
locking will be released and the manual
override will return.
•If the manual override is turned clockwise and
the mark is adjusted to 1, it will be backed to
the reset condition. (Passage P A)
•If the manual override is turned
counterclockwise and the mark is adjusted
to 0, it will be back to the reset condition.
(Passage A R) (Reset state at the time of
shipment.)
Warning
How to Use Plug Connector
Caution
Precautions
4-12-3
Series VQ100
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN

Wiring specifications
앬Lead wires are connected as follows. Connect them to the
power supply side.
DC positive common
DC negative common
AC
앬Plug connector lead wire length
앬How to order connector assembly
Nil 300 mm
600 mm
1000 mm
2000 mm
3000 mm
Lead wire length
A
C
SOL.
(–) Black
(+)
(+) Red
(–)
Lead wire color
Single
Blue
Blue
Lead wire color
Single
SOL.
A
C
Red
Red
Lead wire color
Set
Reset
COM
Latching
SOL.
A
C
B
Lead wire color
Set
Reset
COM
Latching
SOL.
A
C
B
Lead wire color
Set
Reset
COM
Latching
SOL.
A
C
B
Single solenoid (DC) Latching solenoid (DC)
A (–) set
C (+) COM
B (–) Reset
SOL.
Simultaneous energization
protection circuit
Single solenoid (AC) Latching solenoid (AC)
A Set
B Reset
SOL.
C COM
A (–)
(+)
C (+)
(–)
SOL.
A
C
SOL.
B-C
ON (Reset)
Passage Indicator light Single
A-C ON
OFF
Passage
P A
A R
Indicator light
Orange
———
P  A
A  R
Orange
Green
Latching type
A-C
ON (Set)
Indicator light
ON
• ON (Set): Orange
• (Reset: Green) Indicator light
ON
• ON (Set): Orange
• (Reset: Green)
M plug connector L plug connector
DC positive common
• Single
AXT661-14A-
• Latching
AXT661-13A-
DC negative common
• Latching
AXT661-13AN-
100 VAC
• Single
AXT661-31A-
• Latching
AXT661-32A-
200 VAC
• Single AXT661-34A-
• Latching
AXT661-35A-
100 VAC, 200 VAC
100 VAC, 200 VAC
Only connector and sockets
(3 pcs.)
AXT661-12A
Precautions
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
Simultaneous energization protection circuit
Simultaneous energization protection circuit
(–) Black
(+) Red
(–) White
(+) Red
(–) Black
(+) White
Note) Single type:
No polarity
6
10
20
30
The lead wire length of the valve with lead wire is 300 mm.
When ordering a valve with a lead wire of 600 mm or longer, be
sure to indicate the model number of the valve without
connector and connector assembly.
Note 1) Single: No polarity
ON: Orange light lights.
Note 2) Setting side energizing: Orange
light lights.
Resetting side energizing: Green
light lights.
With wrong wiring preventing
ability (stop diode)
With surge voltage suppresser
(ZNR/Surge absorbing diode)
Note 3) A (set) side energizing: P A
B (set) side energizing: A R
Note 4) Negative common specifications
is applicable.
How to Use Plug Connector Light/Surge Voltage Suppressor
Caution
Latching Type
Caution
Caution
Yellow Yellow
Blue Red
Gray Gray
For latching type, set energizing side and reset the energizing
side are indicated with orange and green respectively.
∗( ) and the broken line: Large flow type
The latching solenoid is equipped with a self-holding mechanism,
which permits a movable iron core in the solenoid to hold the “set”
position. Therefore there is no need to energize continuously.
<Special Cautions for Latching Solenoid>
1. Make sure ON and OFF signals are not energized
simultaneously.
2. 10 ms energizing time is necessary for self-holding.
3. Please consult with SMC if using in a place with high vibrations
(10 G or more) or high magnetic fields.
4. Even though this valve is held on to reset position (passage: A
R), it may switch to the set position during transportation or
due to impact when mounting valves, etc. Therefore, check the
initial position by means of power supply or manual override
prior to use.
Series VQ100
4-12-4

Caution
2. Wiring specifications
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
White
Black
Black
Red
Red
Red
Black
Black
White
Black
White
Terminal No./Lead Wire Color
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
SOL.
COM
COM
Pin no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1 station
2 stations
3 stations
4 stations
5 stations
6 stations
7 stations
8 stations
9 stations
10 stations
11 stations
12 stations
13 stations
14 stations
15 stations
16 stations
17 stations
18 stations
Electrical wiring specifications
41
510
16 11
20 17
Multi-connector pin arrangement
Pin no.
Positioning key
For obtaining the flow rate, refer to page 4-1-6.
DIN rail mounting bracket
DIN rail mounting bracket
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
Removal
1. Loosen the clamp screw of the end plate on both sides.
2. Lift the (a) side of the manifold off the DIN rail and slide it in the
direction of the (2) side.
Mounting
1. Hook side (b) of the manifold base on the DIN rail.
2. Press down side (a) and mount the end plate on the DIN rail.
Tighten the clamp screw on the side.
Proper tightening torque of thread: 0.8 to 1.2 N·m
Lead wire color
Dot
marking
Terminal
no.
Lead
wire color
How to Use Circular Connector
(For plug-in manifold: For VV3Q11)
Caution
How to Connect/Disconnect DIN Rail
How to Calculate the Flow Rate
1. Attaching and detaching connectors
If the manual override is manipulated, since any connected
equipment will be activated, make sure to be done only after no
danger is confirmed.
(a)
(1)
(b)
(2)
(a)
(2)
(b)
(1)
Precautions
Body
Ring Positioning key
4-12-5
Series VQ100
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN

How to Order Valves
100 VAC (50/60 Hz)
200 VAC (50/60 Hz)
110 VAC (50/60 Hz)
220 VAC (50/60 Hz)
24 VDC
12 VDC
Other
1
2
3
4
5
6
9
Coil rated voltage
1
2
N.C. (Normally closed)
N.O. (Normally open)
Type of actuation
Series VQ
Compact 3 port valve
Without sub-plate
With sub-plate
With sub-plate
Nil
M3
M5
Port size
Non-locking push type (Tool required)
Latching type: Push-locking type (Tool required)
Locking type (Tool required)
Nil
B∗
Manual override
Standard type (1 W)
High pressure type (1.5W)
Low wattage type (0.5 W)
Latching type,
Positive COM
Latching type,
Negative COM
Large flow type
Nil
H
Y
Function
Electrical entry
F
L
LO
M
MO
G
L plug connector
M plug connector Grommet
3 Port Solenoid Valve
Series VQ100
VQ1 1 0 5 F
∗Option
Note) Except latching and
large flow type.
For the special volt-
ages, please consult
with SMC.
∗Option
Note) Latching manual override: Push-locking type only.
Grommet
Note) Grommet: No latching type, AC and large flow
L∗
N∗
U∗
Note)
Note)
L plug connector, With lead wire
With light/surge voltage suppressor
Plug-in,
With light/surge voltage suppressor
(Only for plug-in manifold)
L plug connector, Without connector
With light/surge voltage suppressor
M plug connector, With lead wire
With light/surge voltage suppressor
M plug connector, Without connector
With light/surge voltage suppressor
For details about the applicable products
conforming to international standards,
visit us at www.smcworld.com.
Note) Normally open type is
available only with
standard type. (1 W)
4-12-6

Standard Specifications
Valve construction
Fluid
Maximum operating pressure
Minimum operating pressure
Allowable voltage fluctuation
Coil insulation type
Item
Flow
characteristics
1  2
2  3
C[dm3/(s·bar)]
b
Cv
C[dm3/(s·bar)]
b
Cv
Response time (1)
Ambient and fluid temperature
Lubrication
Manual override
Mounting orientation
Shock/Vibration resistance (4)
Enclosure
Weight
Coil rated voltage
Power consumption (Current)
DC
1 W (42 mA)
Electrical entry
3 port direct operated poppet (NC)
Air/Inert gas
0.5 W (21 mA)
Valve specificationsElectricity specifications
DC
Standard type
(1 W)
ON: 3.5 ms, OFF: 2 ms
ON: 3.5 ms, OFF: 2.5 ms
(A)
2
Clean Series
How to order manifold
10 VQ110 
Clean Series
JIS Symbol
Normally closed
1
(P)
3
(R)
(A)
2
Latching type
High pressure type
(1.5W)
Low wattage type
(0.5 W)
0.7 MPa 0.8 MPa 0.7 MPa
0.055
0.22
0.014
0.083
0.28
0.021
0.042
0.27
0.011
0.045
0.28
0.012
1.5 W (63 mA)
1
(P)
3
(R)
(A)
2
1
(P)
3
(R)
Normally open
Clean series is available for both standard
and option specifications.
–10 to 50°C
Not required
Non-locking push type/Locking type (Tool required)
Unrestricted
150/30 m/s2
Dustproof
12.6 g (L/M plug connector, Without sub-plate)
24 V, 12 V
±10% of rated voltage
Class B or equivalent
0 MPa (–0.1 MPa )
Grommet
Plug-in, L plug connector, M plug connector
(With light/surge voltage suppressor)
Note 1) Based on JIS B 8374-1993. With light/surge voltage suppressor (Use clean air),
Dispersion accuracy ±1 ms
Note 2) Use dry air to prevent condensation when operating at low temperatures.
Note 3) Locking style: Option
Note 4) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial
direction and at the right angles to the main valve and armature in both
energized and de-energized states every once for each condition. (Values at
the initial period)
Vibration resistance :No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test
was performed at both energized and de-energized states in the axial
direction and at the right angles to the main valve and armature. (Values at
the initial period)
Note 5) In vaccum applications, use 10- Clean Series which can use with 3 (R) port vacuum and 1 (P)
port vaccum release pressure. (Differential pressure between 3 (P) and 1 (P) is up to the
maximum operating pressure for each type.)
Type
(2)
(3)
(5)
4-12-7
3 Port Solenoid Valve Series VQ100
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN

VQ110L-VQ110U-
0.6 MPa
Power
consumption
(Current)
VQ110- 
Latching type AC type
Type
Item
0.7 MPa
0.042
0.27
0.011
0.045
0.28
0.012
0.14
0.26
0.036
0.14
0.25
0.036
0.04
0.11
0.009
0.044
0.3
0.011
Electrical entry (1)
Valve specificationsElectricity specifications
Option
Model
Maximum operating pressure
Ambient and fluid temperature
Response time (2)
24 VDC
12 VDC
100 VAC
110 VAC
200 VAC
220 VAC
1
2VQ120-
0.5 MPa
—
—
—
—
1  2
(3  2)
2  3
(2  1)
Flow
charac-
teristics
C[dm3/(s·bar)]
b
Cv
C[dm3/(s·bar)]
b
Cv
0 MPa(—100 MPa )
5 ms or less
1 W (42 mA)
1 W (83 mA)
0.6 VA (6 mA)
0.65 VA (5.9 mA)
1.2 VA (6 mA)
1.3 VA (5.9 mA)
15 ms or less
—
—
0.5 VA (5 mA)
0.55 VA (5 mA)
1.0 VA (5 mA)
1.1 VA (5 mA)
5 ms or less
0.7 W (29 mA) (3)
0.7 W (58 mA) (3)
5 ms or less
1 W (42 mA)
1 W (83 mA)
Plug-in, L plug connector, M plug connector
(With light/surge voltage suppressor)
Note 1) Grommet is available only for normally open type (without light/surge voltage suppressor).
Normally open type is available only with 1 W DC specifications.
Note 2) With light/surge voltage suppressor based on JIS B 8374-1993 (clean air).
Note 3) Inrush: 3.1 W (10 ms after energized.), Holding: 0.7 W
Note 4) In vacuum applications, use 10- Clean Series which can use with 3 (R) port vacuum and 1 (P)
port vacuum release pressure. (Differential pressure between 3 (P) and 1 (P) is up to the
maximum operating pressure for each type.)
Note 5) In the case of 1 (P) port vacuum, and 3 (R) port vacuum release, use VQ120 (Normally open
type). In this case, 10- is not required.
Note 6) ( ) values insides denote the air passage for normally open type.
(6)
(4)(5 )
(6)
Normally open
type
Large flow type
Series VQ100
4-12-8

Construction
No.
q
w
e
r
t
y
u
i
Description Material
—
Resin
Stainless steel
Stainless steel, Resin
Stainless steel
NBR
Carbon steel
NBR
Component Parts
No.
o
Description Material
ZDC
Part no.
AXT662-1- (1: M5, 2: M3)
1
2
Replacement Parts
RAP
(For N.C. valve)
Solenoid coil
Body
Fixed iron core
Movable iron core assembly
Return spring
Poppet
Round head combination screw
Interface gasket
Sub-plate
Note) 1 set includes: 1 gasket and 2 screws.
Purchasing order is available in units of 10 pieces.
Optional parts
• Gasket, screw: VQ100-GS-5
qertuw
y
i
o
4-12-9
3 Port Solenoid Valve Series VQ100
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN

Grommet
VQ10-G-M5 (M3)
Dimensions
How to Order Valves
VQ1 1 0 5 L M5
Coil rated voltage
Type of actuation
Series VQ
Compact 3 port valve
Without sub-plate
With sub-plate
With sub-plate
Nil
M3
M5
Port size
Non-locking push type (Tool required)
Latching type: Push-locking type (Tool required)
Locking type (Tool required)
Nil
B∗
Manual override
Standard type (1 W)
High pressure type (1.5W)
Low wattage type (0.5 W)
Latching type,
Positive COM
Latching type,
Negative COM
Large flow type
Nil
H
Y
L ∗
N ∗
U ∗
Function
Electrical entry
L
LO
M
MO
G
29.2
6.1 Manual override
4.9
12.4
14.8
12 3.7
18.1
2-ø2.7 mounting hole
5
(4.1)
4.9 9.7
(18.1)
5
(5.9)
30.7
3-M5, (M3)
Locking type manual override
≅300
(Lead wire length)
28
11
7
5
(5.9)
4.9
E
AP
1N.C. (Normally closed)
N.O. (Normally open)
100 VAC (50/60 Hz)
200 VAC (50/60 Hz)
110 VAC (50/60 Hz)
220 VAC (50/60 Hz)
24 VDC
12 VDC
Other
1
2
3
4
5
6
9
Note) Normally open type
is available only with
standard type. (1 W)
∗Option
Note) Except latching and large
flow type.
For the special volt-
ages, please consult
with SMC.
Note) Grommet: No latching type, AC
and large flow
∗ Option
Note) Latching manual override: Push-locking type only.
L plug connector, With lead wire
With light/surge voltage suppressor
L plug connector, Without connector
With light/surge voltage suppressor
M plug connector, With lead wire
With light/surge voltage suppressor
M plug connector, Without connector,
With light/surge voltage suppressor
Grommet
•(): M3
• Broken line: Locking type manual override
Note)
Note)
2
Series VQ100
4-12-10

M plug connector
VQ10-M-M5 (M3)
L plug connector
VQ10-L-M5 (M3)
A P
E
3-M5, (M3)
Manual override
2-ø2.7
(4.1)
(5.9)
(5.9)
(Lead wire length)
Latching, AC,
Large flow type
Locking type manual override
4.9 4.9
11
12
4.9
12.4
14.8
5
9.7
5
7
5
3.7
18.1
6.1
31.5
36.5≅300 (Lead wire length)
32
35.7
(31.5)
41.6≅300
30.7
Latching, AC,
Large flow type
AP
3-M5,(M3)
(4.1)
(5.9)
(5.9)
Lead wire color: Red
Lead wire color: Black
Locking type manual override
4.9
4.9
11
5
9.7
5
7
5
36.7
41.7 ≅300 (Lead wire length)
(30)
30.7
E
Manual override
2-ø2.7 12
4.9
12.4
14.8
3.7
18.1
6.1
30
35.1
Mounting hole
Mounting hole
•(): M3
• Broken line: Latching, AC and large flow capacity
•One dot chain line: Locking type manual override and push-locking
type manual override (latching)
•(): M3
• Broken line: Latching, AC and large flow capacity
•One dot chain line: Locking type manual override and push-locking
type manual override (latching)
Dimensions
4-12-11
3 Port Solenoid Valve Series VQ100
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN