SMC Networks VQD1000 Series User manual

4 Port Direct Operated Poppet
Solenoid Valve
Series VQD1000
Body ported Base mounted
Series
VQD1151U
Average
speed
(mm/s)
400
450
500
350
300
250
200
150
100
50
0
Bore size
Series CJ2
Pressure 0.5 MPa
Load factor 50%
Stroke 60 mm
Series CM2
Pressure: 0.5 MPa
Load ratio: 50%
Stroke: 300 mm
ø6ø10 ø16 ø20 ø25 ø32 ø40
Base mounted Series CJ2 Series CM2
Tube bore x Length TU0425 x 1 m
VQD1151U
Speed controller AS1201F-M5-04 AS2201F-02-04
Silencer AN120-M5
Use as a guide for selection.
Please confirm the actual conditions with SMC Sizing Program.
Cylinder Speed Chart
Base Mounted Conditions
Compact and lightweight (34 g)
with large flow capacity
Body width of 10 mm, C: 0.22 dm3/(s·bar) 2 W
C: 0.27 dm3/(s·bar)
3.2 W (U type: Large flow)
Perpendicular,
upward actuation
Horizontal actuation
Clean room specifications
available as special.
Main valve has no sliding seals or grease
and air is not exhausted to the atmosphere.
∗It is when the cylinder is extending that is meter-out controlled by speed controller which is directly
connected with cylinder, and its needle valve with being fully open.
∗The average velocity of the cylinder is what the stroke is divided by the total stroke time.
∗ Load factor: ((Load weight x 9.8)/Theoretical force) x 100%
Unprecedented high speed,
with stable response times
ON: 4 ms, OFF: 2 ms, Dispersion accuracy
±1 ms (With light/surge voltage suppressor
at a supply pressure of 0.5 MPa)
(Use clean and dry air.)
Available in vacuum applications
(Up to –100 kPa)
(Valve leakage: 0.03 cm3/s He or less)
Can be used in vacuum/release circuits
When used as a 3 port valve, conversion from N.O. to N.C. and
vice versa is possible by plugging either port 4(A) or 2(B).
Copper-free specifications
The fluid contacting section is copper-free and the
standard style can be used as it is.
2-8-1
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 2-9-2.
Connected actuator is started by manual operation.
Use the manual override after confirming that there is
no danger.
Warning
Caution
Non-locking push type (Tool required)
Attaching and detaching connectors
To attach a connector, hold the lever and connector unit
between your fingers and insert straight onto the pins of the
solenoid valve so that the lever’s pawl is pushed into the
groove and locks.
To detach a connector, remove the pawl from the groove by
pushing the lever downward with your thumb, and pull the
connector straight out.
Note) GENTLY pull the lead wire, otherwise it may cause contact
failure or disconnection.
Caution
• Standard: 2 W specifications
• Large flow: 3.2 W specifications (Power saver)
For the 3.2 W specifications (power saver), power consumption
at holding is reduced with the above circuit.
Refer to electrical power waveform as shown below.
<Energy saving type’s electrical power waveform>
(Rated voltage: 24 VDC)
Caution
When it is the manifold and the adjacent valve is
continuously energized, align them so that they would
be energized or de-energized alternately.
 How to order connector assembly
AXT661-14A-
Lead wire length
Nil
6
10
20
30
300 mm
600 mm
1000 mm
2000 mm
3000 mm
24V
0V
3.2W
2.4W
0W 10 to 20 ms
Energy saving type
Applied voltage
ø3
Cover
Groove
Pin
Lever
Connector
Lever
Connector
LED
ZNR
Coil
(+, –)
(–, +)
Lead wire Connector
(+)
(–)
Lead wire Connector
LED
Coil
i1: Inrush current i2: Holding current
Coil temperature may get high due to ambient
temperature or energizing duration. Do not touch the
valve by hand directly.
When there is such a dangerous case to be touched
by hands directly, install a protective cover.
Warning
Caution
After confirming the gasket is correctly placed under
the valve, securely tighten the bolts with the proper
torque shown in the table below.
Proper tightening torque (N·m)
0.18 to 0.25
i1i2
Varistor
Precautions 1
• In order to turn it ON, push down the manual
override button in the direction the arrow ()
indicates until it stops (approx. 0.5 mm), and
release it to turn it OFF. How to Use Plug Connector
Wiring Specifications
Mounting of Valves
Continuous Energization
Manual Override Operation Simultaneous Energization
Timer circuit
Red C
Black A
Red C
Black A
Plug connector lead wire length
Lead wire length of plug connector
valve with lead wire is 300 mm. When
ordering a valve with a lead wire of 600
mm or longer, be sure to indicate the
model number of the valve without
connector and connector assembly.
Series VQD1000
2-8-2

Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 2-9-2.
Caution
Application example of “VQD11 1 V
W”
(Symbols used are typical examples.)
For obtaining the flow rate, refer to pages 2-1-8 to 2-1-11.
Vacuum valve
3(R) 4(A) Vacuum pad
1(P) 2(B)
Vacuum releasing air
Atmospheric pressure or
micro pressure
Precautions 2
2
3
5
2
3
5
• Use a VQD11 1 valve for vacuum applications.
Connect the vacuum source to the 3(R) port.
∗Air pressure cannot be applied to the 3(R) port.
• When used as a 3 port valve, conversion from N.O. to N.C. and
vice versa is possible by plugging either port 4(A) or 2(B).
∗ Cannot be used as 2 port valve.
How to Use the Valve for Vacuum Applications
How to Calculate the Flow Rate
(When used as a 3 port valve)
v
w
2-8-3
Series VQD1000
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

How to Order Valves
L155
VQD11
24 VDC
12 VDC
5
6
Rated voltage
M5
Nil
M5
M5 thread
Without sub-plate (Manifold)
M5 thread
Body ported
Base mounted
Port size
Nil
V
U
W
Valve option
Body type
Note)
Note)
Note) Energy saving type
Electrical entry
Lplug connector
Base mounted
Mplug connector
Base mounted
Standard
(2 W)
Large flow type
(3.2 W, Energy saving type)
4 port direct operated poppet valve
Air/Inert gas
0.7 MPa
0 MPa/–100 kPa
L plug connector, M plug connector
(With indicator light and surge voltage suppressor)
2 W 3.2 W (Energy saving type)
(Inrush: 3.2 W, Holding: 2.4 W)
Item
Type
Valve specifications
Electricity specifications
JIS Symbol
DC
DC
Standard Specifications
(A)
4
(B)
2
1
(P)
3
(R)
2
3
5
Body ported (Single unit)
Body ported (Manifold)
Base mounted
Lplug connector
Body ported
Mplug connector
Body ported
4 Port Direct Operated Poppet
Solenoid Valve
Series VQD1000
Standard (2 W)
Vacuum (2 W)
For large flow (3.2 W)
For large flow, vacuum (3.2 W)
Note) Please consult with
SMC for other
voltages.
Note 1) Based on JIS B 8375-1981. Factor: With light/surge voltage suppressor (Use clean air).
Dispersion accuracy: ±1 ms
Note 2) Operating the valve at low temperatures may cause condensate to form, therefore dry air
must be used.
Note 3) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial
direction and at the right angles to the main valve and armature in both
energized and de-energized states every once for each condition.
(Values at the initial period)
Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000
Hz. Test was performed at both energized and de-energized states in
the axial direction and at the right angles to the main valve and
armature. (Values at the initial period)
ON: 4 ms, OFF: 2 ms
–10 to 50°C(2)
Not required
Non-locking push type
150/30 m/s2
Unrestricted
Dust tight
34 g (Without sub-plate)
24 V, 12 V
±10% of rated voltage
Class B or equivalent
L: Plug lead type
L plug connector, With lead wire
With light/surge voltage suppressor
LO: Plug lead type
L plug connector, Without lead wire
With light/surge voltage suppressor
M: Plug lead type
M plug connector, With lead wire
With light/ surge voltage suppressor
MO: Plug lead type
M plug connector, Without lead wire
With light/surge voltage suppressor
Valve construction
Fluid
Maximum operating pressure
Minimum operating pressure/Vacuum
Response time(1)
Ambient and fluid temperature
Lubrication
Manual override
Shock /Vibration resistance(3)
Mounting position
Enclosure
Weight
Coil rated voltage
Allowable voltage fluctuation
Coil insulation type
Power consumption
Electrical entry
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
2-8-4

Piping plate assembly
VQD1000-20A
Construction
Flow Characteristics
Valve Single Unit Option
Material
—
Aluminum
ZDC
Aluminum
HNBR
Resin
Stainless steel
Aluminum
HNBR
Steel
Note
VQD1000-S-M5 (Base mounted only)
VQD1000-9-1H
AXT632-7-13 (M1.7 x 18)
Solenoid coil assembly
Sub-plate
Body
Spool valve
Poppet
Guide ring
Return spring
Manual override
Gasket
Round head combination screw
Description
Note) Body cannot be disassembled.
3(R) 4(A) 1(P) 2(B)
1(P)
JIS Symbol
(A)
4
(B)
2
1
(P)
3
(R)
Manifold type (VQD1131) can be changed to single unit type (VQD1121) by mounting plate assembly.
Valve model
Body ported VQD1121- -M5
VQD1121 -  -M5
VQD1151--M5
VQD1151
-  - M5
M5 x 0.8
0.22
0.27
0.22
0.27
0.16
0.24
0.10
0.25
0.05
0.07
0.05
0.07
0.19
0.28
0.22
0.27
0.31
0.28
0.31
0.28
0.05
0.07
0.06
0.07
Base mounted
(With sub-plate)
Port size C
[dm3/(s·bar)] bCv
C
[dm3/(s·bar)] bCv
1  4/2 (P  A/B) 4/2  5/3 (A/B  EA/EB)
Flow characteristics
UW
UW
LM
LM
LM
LM
Component Parts
que try!0
i
o
w
No
q
w
e
r
t
y
u
i
o
!0
Note) Plate should be mounted with manifold mounting screws (M1.7 x 20).
Proper tightening torque of thread: 0.18 to 0.25 N·m
2-8-5
4 Port Direct Operated Poppet Solenoid Valve Series VQD1000
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

Dimensions
L plug connector: VQD1121-L-M5
M plug connector: VQD1121-M-M5
Lead wire length 300 mm 2-M5 x 0.8
4(A), 2(B) port
2-ø3.5 mounting hole
2-M5 x 0.7
1(P), 3(R) port
Indicator light
0.6 0.6
5.3 5.3
13
Direct manual override
15
5.5
(11)
34
0.5 0.5
4
2
11
3
6
25.5
29
33
21.5 4
28.5
49
50.5
3
(R)
1
(P)
7.4 3
(13)
Series VQD1000
2-8-6

Dimensions
SMC
55
5.5
5.5
9
2-ø3.5 mounting hole
Lead wire length 300 mm
Indicator
light
27
10.9 9.1
3
11.2
17.5
Direct manual override
4-M5 x 0.8
1 (P), 4(A), 2(B), 3(R) port
13
49
50.5
5.5
12
28.5
33.5
37
M plug connector (M)
4(A)2(B)
3(R)
1(P)
L plug connector (L)
38
1(P)
L plug connector: VQD1151-L-M5
M plug connector: VQD1151-M-M5
2-8-7
4 Port Direct Operated Poppet Solenoid Valve Series VQD1000
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

How to Order Manifold
Plug lead unit
manifold
M5 thread
One-touch fitting for ø4
M5
C4
Cylinder port
(Base mounted only)
2 stations
20 stations (Max.)
02
20
Valve station
How to Order Manifold Assembly
Prefix the asterisk to the part nos. of the solenoid valve, etc.
Enter in order starting from the first station on the D side.
U side
D side
Stations········ 1 2 3 4 5
VQD1151-5L
VQD1000-10A-5
VV4QD15-05M5
1(P), 3(R) port: Rc 1/8
3R 1P
2B
4A
2B
4A
How to Order Valves
24 VDC
12 VDC
5
6
Standard (2W)
Vacuum (2 W)
For large flow (3.2 W)
For large flow, vacuum (3.2 W)
Nil
V
U
W
Valve option
Electrical entry
Note)
Note)
Note) Energy saving type
Body ported
Base mounted
2
5
Manifold
Body ported
Base mounted
3
5
Body type
Port size (Body ported only)
VV4QD1 5
VQD11 L
551M5
M5 thread
M5
Note) Please consult
with SMC for
other voltages.
Specify the part numbers for valves and options together beneath the
manifold base part number.
<Example>
Plug lead unit manifold
VV4QD15-05M5········ 1 set
— Manifold base part no.
∗VVQD1000-10A-5····1 set
— Blanking plate part no. (1st station)
∗VQD1151-5L············4 sets — Valve part no. (2 to 5th station)
Rated voltage
·
·
·
·
·
·
L: Plug lead type
L plug connector, With lead wire
With light/surge voltage suppressor
LO: Plug lead type
L plug connector, Without lead wire
With light/surge voltage suppressor
M: Plug lead type
M plug connector, With lead wire
With light/surge voltage suppressor
MO: Plug lead type
M plug connector, Without lead wire
With light/surge voltage suppressor
Series VQD1000
2-8-8

Blanking plate assembly/Body ported
VVQD1000-10A-2
Blanking plate assembly/Base mounted
VVQD1000-10A-5
Individual SUP spacer/Base mounted
VVQD1000-P-M5-5
Blanking plate assembly includes 2 screws
and gasket
Blanking plate assembly includes 2 screws
and gasket
9.5
10.8
29
4.5
0.8
Exhaust port
M5 x 0.8
Individual EXH spacer with screw (2 pcs.)
and gasket
9.5
10.8
29
4.5
0.8
Supply port
M5 x 0.8
Individual SUP spacer with screw (2 pcs.)
and gasket
Mount the individual SUP spacer on the manifold base, and thus making it possible to have supply port individually for each valve.
Individual EXH spacer/Base mounted
VVQD1000-R-M5-5
Mount the individual EXH spacer on the manifold base, and thus making it possible to have supply port individually for each valve. (Common EXH type)
Manifold Option
2-8-9
4 Port Direct Operated Poppet Solenoid Valve Series VQD1000
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

Plug lead unit manifold (VV4QD12-)
2345678910
L1
L2
n: Stations
n
L11 12 13 14 15 16 17 18 19 20
28
20
39
31
50
42
61
53
72
64
83
75
94
86
105
97
116
108
127
119
138
130
149
141
160
152
171
163
182
174
193
185
204
196
215
207
237
229
1
226
218
12345 n
Direct manual override
(Non-locking)
24
15
L plug connector (L)
M plug connector (M)
8
7
43
0.6
5.35.3
0.5 0.5
57
15
P = 11 10
4L2
L1
52
50.5
30 176.5
42
38
35
2
4
2
4
2
4
2
4
2
4
R 3
P 1
P 1
R 3
Lead wire length 300 mm
1(P), 3(R) port
4-Rc 1/8
M5: M5 thread
2n-M5 4(A), 2(B) port
Indicator light
2-ø4.5 (Mounting hole)
Dimensions
U side
D side
Stations
Dimensions
Series VQD1000
2-8-10