SMC Networks S0700 User manual

Series S0700
7 mm Width Compact Pilot Type 5 Port Solenoid Valve
Rubber Seal
77
Width:
7
mm
0.39
0.39
0.11
Flow Characteristics
C
[
dm3
/(
s·bar)
]:
0.39
b:
0.39
Cv:
0.11
609
SJ
SY
SV
SYJ
SZ
VP4
S0700
VQ
VQ4
VQ5
VQC
VQZ
SQ
VFS
VFR
VQ7
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 609

Series S0700
7 mm Width Compact Pilot Type 5 Port Solenoid Valve
7 mm Width Compact Pilot Type 5 Port Solenoid Valve
Compact Design with High Flow Capacity
Compact Design with High Flow Capacity
Series Type of
actuation Model 1
® 4/2 (P ® A/B)
Response
time
(msec)
Flow characteristics
Plug-in
type
Plug lead
type
2 position
4 position
2 position
4 position
Single
Double
Dual 3 port
valve
S0710
S0720
S07 0
S0715
S0725
S07 5
18 or less
10 or less
18 or less
12 or less
10 or less
12 or less
Single
Double
Dual 3 port
valve
C [dm3/(s·bar)]
0.39
0.39
0.34
0.39
0.39
0.34
b
0.39
0.39
0.34
0.39
0.39
0.34
Cv
0.11
0.11
0.09
0.11
0.11
0.09
4/2 ® 5/3 (A/B ® R1/R2)
C [dm3/(s·bar)]
0.37
0.37
0.33
0.37
0.37
0.33
b
0.39
0.39
0.33
0.39
0.39
0.33
Cv
0.10
0.10
0.08
0.10
0.10
0.08
A
B
C
A
B
C
Note 2)
Note 1) The value for cylinder port fitting port size C6.
Note 2) Based on JIS B 8375-1993 (Supply pressure: 0.5 MPa, with indicator light and surge voltage suppressor, clean air. This will change depending on pressure and air
quality.) The value when ON for the double type.
610
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 610

4 Position Dual 3 Port Valve
Many Combinations Available to Fit Your Needs
Many Combinations Available to Fit Your Needs
Tkit Terminal
Block Lkit Lead Wire
M kit Circular
Connector Ckit Lead Wire
Skit Serial
Transmission
Skit
Fkit D-sub
Connector Pkit Flat Ribbon Cable Jkit
PC Wiring System
Compatible Flat
Ribbon Cable
EX500 EX510 EX250
8.5 mm
7.5 mm
The mounting screw is tightened with the valve.
Applicable to Serial Wiring
Gateway System
Applicable to Serial Wiring
Gateway System
Series Applicable protocol Model
· DeviceNet
· PROFIBUS DP
· CC-Link
· EtherNet/IP
· DeviceNet
· PROFIBUS DP
· CC-Link
· DeviceNet
· PROFIBUS DP
· CC-Link
· AS-Interface
· ControlNet
· CANopen
· EtherNet/IP
EX500
EX510
EX250
Gateway System
Serial Transmission
System
Gateway System
Serial Transmission
System
Integrated Type
(For I/O)
Serial Transmission
System
• Two 3 port valves in one body.
• Independently operating 3 port
valve at each side of A and B.
• Number of stations occupied
for 3 port valve – halved.
• Available as 4 position 5 port
valve.
N.C. N.C.
N.O. N.O.
N.C. N.O.
A side B side
1
(P)
5
(R1) 3
(R2)
4
(A) 2
(B)
1
(P)
5
(R1) 3
(R2)
4
(A) 2
(B)
1
(P)
5
(R1) 3
(R2)
4
(A) 2
(B)
Symbol
4 Position Dual 3 Port Valve
series
EX500
15
14
7
6
9
8
1
0
2 Types of Manifold
Pitch Are Selectable.
2 Types of Manifold
Pitch Are Selectable.
(Plug lead type)
8.5 mm pitch
with one-touch fittings
(ø2, ø3.2, ø1/8, ø5/32)
7.5 mm pitch
with barb fittings
(ø2, ø3.2, ø4)
611
SJ
SY
SV
SYJ
SZ
VP4
S0700
VQ
VQ4
VQ5
VQC
VQZ
SQ
VFS
VFR
VQ7
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 611

Gateway System
Serial Transmission System
Plug-in type
Stacking base
Plug lead type
Bar base
Applicable network
· DeviceNet
· PROFIBUS DP
· CC-Link
· EtherNet/IP
MIL standard
F Kit
D-sub Connector
S Kit
Serial Transmission
Base Mounted
EX500
Integrated Type (For I/O)
Serial Transmission System
Applicable network
· DeviceNet
· PROFIBUS DP
· CANopen
· CC-Link
· AS-Interface
· ControlNet
·
EtherNet/IP
EX250
Gateway System
Serial Transmission System
Applicable network
· DeviceNet
· PROFIBUS DP
· CC-Link
EX510
Page 624
Page 618
Page 662
Page 620
Blanking plate
SS0700-10A-1
P.648 Built-in silencer,
Direct exhaust [-S]
P.648 EXH block plate
SS0700-B-R
P.649
Blanking plate with output
SS0700-1C-
P.650
External pilot [-R] P.648 P.648 SUP block plate
SS0700-B-P
Spacer for Individual
SUP/EXH
SS0700-PR-1
P.649 Back pressure check
valve [-B] SS0700-7A-1
P.649
Options
Plug-in / Options
Blanking plate
SS0700-10A-5
P.664 Individual SUP spacer
SS0700-P-5-M5
P.664 Individual EXH spacer
SS0700-R-5-M5
P.664 Port plug
VVQ0000-CP
P.664
Plug Lead / Options
P
R
Port plug
*Compatible with 8.5 mm pitch only.*Compatible with 8.5 mm pitch only.
EX500
series
EX500
series
0
1
8
9
6
7
14
15
External pilot port
(M5 x 0.8)
Exhaust port
EXH passage
Blanking plate
with output
SUP passage
U side
D side
D side
U side
612
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 612

MIL standard
· 26 pins, 20 pins
P Kit
Flat Ribbon Cable
MIL standard
· 20 pins
J Kit
PC Wiring System Compatible
Flat Ribbon Cable
T Kit
Terminal Block
L Kit
Lead Wire
M Kit
Circular Connector
Page 658
Page 644Page 640Page 636Page 628 Page 632
C Kit
Lead Wire
DIN rail mounting
bracket
P.650
Blanking plug
(for one-touch fitting)
KJP-02
KQ2P-23/04/06
P.650
Silencer (for EXH port)
AN200-KM8
P.651
Perfect block (Separated)
VQ1000-FPG-
P.652
Blanking plug
(for one-touch fitting)
KJP-02
KQ2P-23/04/06
P.666 Silencer
(for manifold EXH port)
AN110-01
P.666
Double check block
(Separated)
VQ1000-FPG-
P.665
To CYL port
External pilot [-R] P.664
External pilot port
(M3 x 0.5)
Name plate P.651
DIN rail mounting
bracket
To CYL port
AN200
SMC
8765431
2
Port plug
VVQ0000-CP
P.650
B port
A port
613
SJ
SY
SV
SYJ
SZ
VP4
S0700
VQ
VQ4
VQ5
VQC
VQZ
SQ
VFS
VFR
VQ7
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 613

Valve Specifications
Valve Specifications
Model
Series Type of
actuation
Flow characteristics
Cv
Plug-in type
2 position
4 position
2 position
4 position
Plug lead
type
Single
Double
Dual 3 port
valve
Single
Double
Dual 3 port
valve
Model
S0710
S0720
S07 0
S0715
S0725
S07 5
A
B
C
A
B
C
Note 2)
Response
time (msec)
Mass
(g)
0.10
0.10
0.08
0.10
0.10
0.08
b
0.39
0.39
0.33
0.39
0.39
0.33
C[dm3/(s·bar)]
0.37
0.37
0.33
0.37
0.37
0.33
18 or less
10 or less
18 or less
12 or less
10 or less
12 or less
30
38
38
28
36
36
4/2→5/3 (A/B→R1/R2)
Cv
0.11
0.11
0.09
0.11
0.11
0.09
b
0.39
0.39
0.34
0.39
0.39
0.34
C[dm3/(s·bar)]
0.39
0.39
0.34
0.39
0.39
0.34
1→4/2 (P→A/B)
Valve construction
Fluid
Max. operating pressure
Min. operating pressure
Ambient and fluid temperature
Max. operating cycle
Pilot valve exhaust method
Pilot valve manual override
Lubrication
Impact resistance/Vibration
resistance Note 3)
Enclosure
Coil rated voltage
Allowable voltage fluctuation
Coil insulation type
Power consumption
(Current)
Rubber seal
Air/Inert gas
0.7 MPa
0.2 MPa
–10 to 50°C Note 1)
5 Hz
Push type
Not required
30/100 m/s2
IP40
24 VDC
±10% of rated voltage
Class B or equivalent
DC 0.35 W (15 mA)
Plug-in type
Common exhaust Note 2)
24 VDC
Plug lead type
Individual exhaust
Standard Specifications
Note 1) The value for cylinder port fitting port size C6.
Note 2) Based on JIS B 8375-1993 (Supply pressure: 0.5 MPa, with indicator light and surge voltage suppressor, clean air. This will change depending on pressure and air quality.)
The value when ON for the double type.
Valve specification
Electrical
specification
Use dry air to prevent condensation when operating at low temperatures.
Valves with the external pilot specifications have a pilot EXH with individual exhaust specifications.
Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction
and at the right angles to the main valve and armature in both energized and de-
energized states every once for each condition.
Vibration resistance : No malfunction occurred in a one-sweep test between 8.3 and 2000 Hz. Test
was performed at both energized and de-energized states in the axial direction
and at the right angles to the main valve and armature.
Note 1)
Note 2)
Note 3)
614
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 614

Manifold Specifications
Manifold Specifications
Model
Base model
Port specification
Port size
Note 3)
5-station
mass (g)
Note 1)
Applicable
stations
Note 3)
Addition
per/station (g)
Max. 16 stations
Max. 24 stations
Max. 24 stations
Max. 24 stations
Max. 16 stations
Max. 20 stations
Max. 24 stations
Max. 24 stations
Max. 20 stations
Max. 16 stations
Max. 20 stations
360
560
330
325
325
660
455
390
115
155
75
20
20
20
20
20
20
20
20
20
20
10
S kit: Serial transmission
(EX500)
S kit: Serial transmission
(EX250)
F kit: D-sub connector
P kit: Flat ribbon cable
T kit: Terminal block
L kit: Lead wire
M kit: Circular connector
C kit: Lead wire
S kit: Serial transmission
(EX510)
C kit: Lead wire
4(A), 2(B)
C2 (for ø2)
C3 (for ø3.2)
C4 (for ø4)
N1 (for ø1/8")
N3 (for ø5/32")
1(P), 3(R)
C8 (for ø8)
Option
(Direct exhaust
with built-in
silencer)
Type of connection
SS0750-
SS0755-CC
(Manifold pitch: 8.5)
S075-5-M5
SS0755-VC
(Manifold pitch: 7.5)
Note 1) Maximum stations in case of mixed single and double wiring
Note 2) Differs depending on the serial unit type. For details, refer to page 620.
Note 3) Weight excluding valve. Refer to page 614 for valve mass.
Note 4) Weight with 1 input block
Note 5) Weight for lead wire length 0.6 m
Note 6) Weight of sub-plate only. Refer to page 614 for valve mass.
M5 thread
C2 (for ø2)
C3 (for ø3.2)
C4 (for ø4)
N1 (for ø1/8")
N3 (for ø5/32")
M5 thread Connector kit — 14
M3 (M3 thread)
V2 (Barb fitting for ø2)
V3 (Barb fitting for ø3.2)
V4 (Barb fitting for ø5)
Rc 1/8
M5 thread
M5 thread
J kit: PC wiring compatible
flat ribbon cable
Plug-in typePlug lead typeSingle unit
Note 4)Note 2)
Note 5)
Note 6)
615
SJ
SY
SV
SYJ
SZ
VP4
S0700
VQ
VQ4
VQ5
VQC
VQZ
SQ
VFS
VFR
VQ7
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 615

Cylinder Speed Chart
Symbol
Use as a guide for selection.
Please confirm the actual conditions with
SMC Sizing Program.
Series
S0715-5G-M5
Average
speed
mm/s
Bore size
ø6 ø10 ø16 ø20 ø25 ø32 ø40
800
700
600
500
400
300
200
100
0
Base Mounted
Conditions
S0715-5G-M5
Base mounted
Tube bore x Length
Speed controller
Silencer
Series CJ2 Series CM2
ø6 x 1 m
AS2301F-06
AN120-M5
AS2001F-06
Model
S0710
S0715
S07C0
S07C5
S07B0
S07B5
S07A0
S07A5
S0720
S0725
Type of actuation JIS symbol
2 position single
2 position double
4 position dual 3 port
N.C. + N.C.
(Exhaust center)
4 position dual 3 port
N.O. + N.O.
(Pressure center)
4 position dual 3 port
N.C. + N.O.
(A)
4
(B)
2
5
(R1)
1
(P)
3
(R2)
(A)
4
(B)
2
5
(R1)
1
(P)
3
(R2)
4
(A)
2
(B)
5
(R1) 1
(P)
3
(R2)
4
(A)
2
(B)
5
(R1) 1
(P)
3
(R2)
4
(A)
2
(B)
5
(R1) 1
(P)
3
(R2)
Series CJ2
Pressure 0.5 MPa
Load factor 50%
Stroke 60 mm
Series CM2
Pressure 0.5 MPa
Load factor 50%
Stroke 300 mm
Perpendicular,
upward actuation
Horizontal
actuation
* It is when the cylinder is extending that is meter-out controlled by speed controller which is
directly connected with cylinder, and its needle valve with being fully open.
* The average velocity of the cylinder is what the stroke is divided by the total stroke time.
* Load factor: ((Load weight x 9.8)/Theoretical force) x 100%
616
Series S0700
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 616

Plug-in
S Kit
Serial Transmission
Stacking Base
Gateway System
Serial Transmission System
EX500 P.618
Integrated Type (For I/O)
Serial Transmission System
EX250
P.620
617
SJ
SY
SV
SYJ
SZ
VP4
S0700
VQ
VQ4
VQ5
VQC
VQZ
SQ
VFS
VFR
VQ7
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 617

S
SS0750 SDA208 C4 B
Voltage: 24 VDC
S07 1 0 5
Base mounted plug-in
EX500
series
Note) Not compatible with dual 3 port valves.
Refer to pages 1680 to 1694 for the details of EX500 gateway system
serial transmission system.
S0700
Kit (Serial Transmission)
EX500 Gateway System Serial Transmission System
How to Order Manifold
Cylinder port size
Symbol
C2
C3
C4
CM
N1
N3
NM
Port size
With one-touch fitting for ø2
With one-touch fitting for ø3.2
With one-touch fitting for ø4
Mixed size/with port plug Note)
With one-touch fitting for ø1/8"
With one-touch fitting for ø5/32"
Mixed size/with port plug Note)
Metric
Inch
Stations
Symbol
01
16
Stations
1 station
16 stations
Note) The maximum number of stations will be dif-
ferent depending on the wiring specification.
··· ···
Note)
Note) Specify “Mixed size/with port plug” in the manifold
specification sheet.
Nil
B
Note 2)
D
D0
D Note 3)
K
Note 4)
N
R
Note 5)
S
Stations
None
With back pressure check valve (all stations)
With DIN rail (Rail length: Standard)
Without DIN rail (with bracket)
With DIN rail Designated length (: station)
Special wiring specification (Except double wiring)
With name plate
External pilot
Built-in silencer
Option
Note 1) When two or more options are specified, indicate them alphabetically.
Example) -BRS
Note 2) When installing a back pressure check valve on the required station, enter
the part number and specify the station position in the manifold specification
sheet.
Note 3) The available number of stations is larger than the number of manifold
stations.
Note 4) Indicate the wiring specification for mixed single and double wirings.
Note 5) For details, refer to page 648.
∗
For manifold optional parts, refer to pages 648 to 652.
∗ For manifold exploded view, refer to page 654.
Symbol
Kit name
1 to 8 stations
Decentralized serial wiring
serial transmission
S kit
Kit name SpecificationSymbol
Without serial unit
DeviceNet, PROFIBUS DP, CC-Link, EtherNet/IP
Standard station
Max. number of
stations for special
wiring specification
16 stations
Max. number of
solenoids
16
SD0
SDA2
Note 1) The maximum number of stations is determined by the total number of solenoids.
For mixed single and double wirings, enter “-K” to the order code options.
Note 2) For SI unit part number, refer to page 655.
Single type
1
Double, Dual 3 port type
2
Type of actuation
Number of solenoids
SI unit COM.
SI unit COM.
+COM.
–COM.
N
EX500
Note) Without SI unit (SD0), the symbol is nil.
Nil
DeviceNet PROFIBUS DP CC-Link EtherNet/IP
How to Order Valves
Type of actuation
Note) For JIS symbol, refer to page 616.
Symbol
1
2
A
B
C
Specification
2 position single
2 position double
4 position dual 3 port type (N.C. + N.O.)
4 position dual 3 port type (N.O. + N.O.)
[Pressure center]
4 position dual 3 port type (N.C. + N.C.)
[Exhaust center]
Specification
Standard
External pilot Note)
Symbol
Nil
R
Function
1 set – Manifold base part no.
3 sets – Valve part no. (Stations 1 to 3)
2 sets – Valve part no. (Stations 4 to 5)
2 sets – Valve part no. (Stations 6 to 7)
1 set – Blanking plate part no. (Station 8)
SS0750-08C4SDA2 ·····
∗ S0710-5 ····················
∗ S0720-5 ····················
∗ S07A0-5 ···················
∗ SS0700-10A-1 ··········
How to Order Manifold Assembly
<Example>
Serial transmission kit
Specify the part numbers for valves and
options together beneath the manifold base
part number.
Prefix the asterisk to
the part nos. of the
solenoid valve, etc.
Write sequentially from the
1st station on the D side.
When part nos. written
collectively are complicated,
specified by using the
manifold specification sheet.
1 2 3 ······ S
tations
Dside Uside
618
P0609-P0680-E080904.qxd 08.9.4 11:34 AM Page 618