SMC Networks SV Series User manual

Serial wiring
with input/output
unit
EX250
SV1000
2000
3000
DeviceNetTM
PROFIBUS-DP
CC-Link
AS-i
CANopen
ControlNetTM
EtherNet/IPTM
Applicable protocol
Applicable
manifold
Series
VQC1000
2000
4000
DeviceNetTM is a trademark of ODVA.
ControlNetTM is a trademark of ControlNet International.
EtherNet/IPTM is a trademark used under license by ODVA.
Information
Serial Wiring with Input/Output Unit
5 Port Solenoid Valve for EX250
Series SV/VQC
쎲Compatible with DHCP
쎲Communication speed: 10 M/100 Mbps
쎲Able to HOLD/CLEAR the output in case of
an error occurrence.
EtherNet/IP™compatible products
are now available.
Series SV
Series VQC
Akihabara UDX 15F,
4-14-1, Sotokanda, Chiyoda-ku,
Tokyo 101-0021, JAPAN
URL http://www.smcworld.com
©2006 SMC Corporation
All Rights Reserved
06-E532 Issued: September, 2006
D-DNP P-120 (DN)
1

W 10S1
1
2
3
SV1000
SV2000
SV3000
Series
Stations
Note
Double wiring
specification Note 1)
Specified layout Note 2)
(Up to 32
solenoids possible.)
Symbol
02
16
02
20
No. of stations
2 stations
16 stations
2 stations
20 stations
• When an AS-i compatible SI unit is used, the
maximum numbers of solenoids are as follows:
8in/8out specification: Maximum 8 solenoids
4in/4out specification: Maximum 4 solenoids
Note 1) Double wiring specifica-
tion: Single, double, 3
position and 4 position
solenoid valves can be
used on all manifold
stations.
Use of a single solenoid will result
in an unused control
signal. If this is not
desired, order with a
specified layout.
Note 2) Specified layout: Indicate
wiring specification in the
manifold specification
sheet. (Note that double, 3
position and 4 position valves
cannot be used where
single solenoid wiring has
been specified.)
쎲Tie-rod Base
SS5V D1
Input block common
specification
+COM. or without input block
–COM.
Nil
N
A, B port size (Inch)
A, B port
Symbol
N1
N3
N7
N3
N7
N9
N7
N9
N11
M
With one-touch fitting for ø1/8"
With one-touch fitting for ø5/32"
With one-touch fitting for ø1/4"
With one-touch fitting for ø5/32"
With one-touch fitting for ø1/4"
With one-touch fitting for ø5/16"
With one-touch fitting for ø1/4"
With one-touch fitting for ø5/16"
With one-touch fitting for ø3/8"
A, B ports mixed
With one-touch
fitting for
ø5/16"
P, E port
Applicable series
SV1000
SV2000
SV3000
With one-touch
fitting for
ø3/8"
With one-touch
fitting for
ø3/8"
A, B port size (Metric)
A, B port
Symbol
C3
C4
C6
C4
C6
C8
C6
C8
C10
M
With one-touch fitting for ø3.2
With one-touch fitting for ø4
With one-touch fitting for ø6
With one-touch fitting for ø4
With one-touch fitting for ø6
With one-touch fitting for ø8
With one-touch fitting for ø6
With one-touch fitting for ø8
With one-touch fitting for ø10
A, B ports mixed
With one-touch
fitting for
ø8
P, E port
Applicable series
SV1000
SV2000
SV3000
With one-touch
fitting for
ø10
With one-touch
fitting for
ø12
SI unit
DeviceNet
PROFIBUS-DP
CC-Link
AS-i 8in/8out 31Slave Mode , 2 power supply systems
AS-i 4in/4out 31Slave Mode , 2 power supply systems
AS-i 8in/8out 31Slave Mode, 1 power supply system
AS-i 4in/4out 31Slave Mode, 1 power supply system
CANopen
ControlNet (IP40)
EtherNet/IP
Without SI unit, Without end plate
QW
NW
VW
TAW
TBW
TCW
TDW
YW
ZCN
ZEN
0
• Input blocks cannot be mounted without SI unit.
• When the DIN rail is included without an SI unit, the DIN rail length will
accommodate an SI unit and one input block.
Note 1) There is a limit on the current supplied from an SI unit of AS-i
compatible 1 power supply system specification to an input block or
valve. For details, refer to page 13.
Note 2) IP40 when the SI unit spec is only compatible with ControlNet.
(Manifold model no. is “SS5V쏔-10S1ZCN쏔쏔쏔D”.)
Note 3) For SI unit part no., refer to page 3.
∗In the case of mixed specification (M), indicate separately in the manifold specification sheet.
∗Port sizes of X, PE port for external pilot specification (R, RS) are ø4 (metric), ø5/32" (inch) for the SV1000/2000 series and ø6
(metric) and ø1/4" (inch) for the SV3000 series.
Input block stations
None
1 station
8 stations
Nil
1
8
Note) Without SI unit, the
symbol is nil.
When an AS-i compatible
S kit is used, there is
a limit on the
maximum number of
stations. For details,
please refer to page
13.
How to Order
EX250 Serial Wiring
With Input/Output Unit
Series SV
05 U
P, E port position
U
D
B
U side (2 to 10 stations)
D side (2 to 10 stations)
Both sides (2 to 20 stations)
3 stations
20 stations
When a longer DIN rail is
desired than the specified
stations.
(Specify a longer rail than
the standard length.)
Mounting
Nil
D
D0 Note)
D3
D20
Note) In the case of D0, only DIN rail
brackets are attached.
SUP/EXH block assembly specification
Internal pilot
Internal pilot, Built-in silencer
External pilot
External pilot, Built-in silencer
Nil
SNote)
R
RS Note)
Note) When the built-in silencer type is used,
keep the exhaust port from coming in
direct contact with water or other liquids.
Enclosure
IP67 specification
QW
Without input block
M12 2 inputs
M12 4 inputs
M8 4 inputs
Input block type
Nil
1
2
3
Note) Without SI
unit, the
symbol is nil.
For details about certified products conforming to
international standards, visit us at www.smcworld.com.
Direct mounting
DIN rail mounting (with DIN rail)
DIN rail mounting (without DIN rail)
... ...
... ...
... ...
... ...
2

How to Order Valve Manifold Assembly (Example)
Example (SV1000)
Manifold
SS5V1-W10S1QW11ND-05B-C6 (1 set)
Double solenoid
SV1200-5FU (3 sets)
Single solenoid
SV1100-5FU (2 sets)
Input block
(M12: 2 inputs, 1 station)
321
Stations
SS5V1-W10S1QW11ND-05B-C6 ......... 1 set (Manifold base part no.)
∗ SV1100-5FU ......... 2 sets (Single solenoid part no.)
∗ SV1200-5FU ......... 2 sets (Double solenoid part no.)
SV 1 0 0 F5
Rated voltage
524 VDC
1
How to Order Solenoid Valves
Pilot
∗External pilot specification
is not applicable for 4
position dual 3 port valves.
Internal pilot
External pilot
Nil
RBack pressure check valve
∗Built-in back pressure
check valve type is
applicable to the SV1000
series only.
None
Built-in
Nil
K
Note)
• For solenoid valve specifications and dimensions, refer to the SV series in
the “Best Pneumatics 2004 Vol. 1” catalog.
• For SI unit dimensions, refer to page 12.
• For details on the SI unit, refer to the separate technical instruction manual.
Series
1
2
3
SV1000
SV2000
SV3000
Type of actuation
1
2
3
4
5
A
B
C
2 position single solenoid
2 position double solenoid
3 position closed center
3 position exhaust center
3 position pressure center
4 position dual 3 port valve: N.C./N.C.
4 position dual 3 port valve: N.O./N.O.
4 position dual 3 port valve: N.C./N.O.
∗4 position dual 3 port valves are applicable to the
SV1000 and SV2000 series only.
Light/surge voltage suppressor
With light/surge voltage suppressor
With surge voltage suppressor
U
R
Note) Available with manifold block
for station additions. Refer to
“Best Pneumatics 2004 Vol. 1”
catalog.
Manual override
Nil: Non-locking push
type
D: Push-turn locking
slotted type
QW
NW
VW
YW
ZCN
Symbol Protocol type
DeviceNet
PROFIBUS-DP
CC-Link
CANopen
ControlNet
EX250-SDN1
EX250-SPR1
EX250-SMJ2
EX250-SCA1
EX250-SCN1
SI unit part no.
SI Unit Part No.
TAW
TBW
TCW
TDW
ZEN
Symbol Protocol type
AS-i 8in/8out 31Slave Mode, 2 power supply systems
AS-i 4in/4out 31Slave Mode, 2 power supply systems
AS-i 8in/8out 31Slave Mode, 1 power supply system
AS-i 4in/4out 31Slave Mode, 1 power supply system
EtherNet/IP
EX250-SAS3
EX250-SAS5
EX250-SAS7
EX250-SAS9
EX250-SEN1
SI unit part no.
End plate
SI Unit Part No.
D side
U side
3
EX250 Serial Wiring with Input/Output Unit Series SV

01 1 station
The maximum number of
stations differs depending
on the kits.
B5
LM
C3
C4
C6
M5
CM
L3
L4
L6
L5
B3
B4
B6
With one-touch fitting for ø3.2
With one-touch fitting for ø4
With one-touch fitting for ø6
M5 thread
Mixed size/with port plug
Elbow top ported with one-
touch fitting for ø3.2
Elbow top ported with one-
touch fitting for ø4
Elbow top ported with one-
touch fitting for ø6
Elbow bottom ported with
one-touch fitting for ø3.2
Elbow bottom ported with
one-touch fitting for ø4
Elbow bottom ported with
one-touch fitting for ø6
M5 thread
Mixed size for elbow piping
M5 thread
Nil
B
D
D쏔
K
N
R
S
Note 1) When two or more options are specified, indicate
them alphabetically.
Example) -BRS
Note 2) When installing a back pressure check valve on the
required station, enter the part number and specify
the station position in the manifold specification
sheet.
Note 3) For special DIN rail length, indicate “D쏔”. (Enter the
number of stations inside 쏔.)
Example: -D08
In this case, stations will be mounted on a DIN rail for 8
stations regardless of the actual number of manifold
stations.
The specified number of stations must be larger than the
number of stations on the manifold.
Indicate “D0” for the option without DIN rail.
Note 4) Be sure to indicate the wiring specification in the
specification sheet.
Note 5) For external pilot option, “-R”, indicate the external
pilot specification “R” for the applicable valves as
well.
Note 6) The built-in silencer type does not satisfy the IP67
standard.
Nil PNP or without input block
NPN
N
Nil
1
2
3
Nil
0
1
8
1VQC1000
Series
Manifold
Stations
08 SDQ
VV5QC 1 1C6
Option
Input block COM.
Kit name
(For details on kits, refer to the next page.)
Number of input blocks
Input block type
Cylinder port size
SKit
B
Nil
SI unit COM.
+COM.
–COM.
N
SI unit COM.
Note) When an AS-i compatible S kit is
used, there is a limit on the
maximum number of stations.
For details, please refer to page 13.
1Plug-in manifold
Note 1) Indicate the size in the specification
sheet in the case of “CM” and “LM”.
Note 2) Symbols for inch sizes are as
follows:
• N1: ø1/8"
• N3: ø5/32"
• N7: ø1/4"
• NM: Mixed
The top ported elbow is LN쏔and the bottom
ported elbow is BN쏔.
None
With back pressure check valve (all stations) Note 2)
With DIN rail (Rail length: Standard)
With DIN rail (Rail length: Special) Note 3)
Special wiring specification (Except double wiring) Note 4)
With name plate
External pilot Note 5)
Built-in silencer, Direct exhaust Note 6)
Without input block
M12 2 inputs
M12 4 inputs
M8 4 inputs
Without SI unit
Without input block
With 1-input block
With 8-input block
Note) Without SI unit, the symbol is nil.
DeviceNet PROFIBUS-DP CC-Link AS-i CANopen EtherNet/IPControlNet
EX250
Plug-in Manifold
Series VQC1000
Base Mounted
For details about certified products conforming to
international standards, visit us at www.smcworld.com.
How to Order Manifold
... ...
... ...
4

VQC 1 05
0
Series
1VQC1000
1
Seal
Metal seal
Rubber seal
0
1
Rated voltage
524 VDC
Function
Note 1) Metal seal type only.
Note 2) When two or more symbols are
specified, indicate them
alphabetically.
Note 3) It is not applicable to dual 3 port
valves.
Note 4) Use a low wattage type for
continuous energization (when
the totaled energized time per
day is longer than the
non-energized time.)
Standard (1 W)
High-pressure type (1.0 MPa)
Negative COM.
External pilot
Low-wattage type (0.5 W)
Nil
KNote 1)
N
RNote 3)
YNote 4)
With/Without light/surge
voltage suppressor
Ye s
Nil
Manual override
Nil: Non-locking
push type
(Tool required)
B: Locking type
(Tool required)
C: Locking type
(Manual)
D: Slide locking type
(Manual)
Type of actuation
2 position single
2 position double (Metal)
2 position double (Rubber)
3 position closed center
3 position exhaust center
3 position pressure center
1
4 position dual 3 port valve
(A)
4 position dual 3 port valve
(B)
4 position dual 3 port valve
(C)
ANote)
BNote)
CNote)
2
3
4
5
AB
PEBEA
AB
EA P EB
AB
P
EA EB
AB
EBPEA
1
53
42
N.C N.C
1
53
42
N.O N.O
1
53
42
N.C N.O
AB
PEA EB
AB
PEA EB
Note) Rubber seal type only.
Note) There is a limit on the current supplied from an SI unit of the SDTC or SDTD specification to an input block or valve. For details, refer to page 13.
• IP40 for the S kit only, which is compatible with ControlNet. (The other S kits are competible with IP67 ratings.)
Kit name
SD0
SDQ
SDN
SDV
SDTA
SDTB
SDTC Note)
SDTD Note)
SDY
SDZCN
SDZEN
Without SI unit, Without end plate
DeviceNet
PROFIBUS-DP
CC-Link
AS-i 8in/8out 31Slave Mode, 2 power supply systems
AS-i 4in/4out 31Slave Mode, 2 power supply systems
AS-i 8in/8out 31Slave Mode, 1 power supply system
AS-i 4in/4out 31Slave Mode, 1 power supply system
CANopen
ControlNet (IP40)
EtherNet/IP
EX250-SDN1
EX250-SPR1
EX250-SMJ2
EX250-SAS3
EX250-SAS5
EX250-SAS7
EX250-SAS9
EX250-SCA1
EX250-SCN1
EX250-SEN1
—
1 to 12 stations
(24 stations)
1 to 12 stations
(24 stations)
1 to 4 stations (8 stations)
1 to 2 stations (4 stations)
1 to 4 stations (8 stations)
1 to 2 stations (4 stations)
Symbol Protocol type No. of stations SI unit part no.
SKit
(Serial transmission kit for I/O)
IP67
IP40
SI unit: EX250
SI unit
Input block
End plate
• For solenoid valve specifications and dimensions, refer to the VQC series in the “Best Pneumatics 2004 Vol. 2” catalog.
• For SI unit dimensions, refer to page 12.
• For details on the SI unit, refer to the separate technical instruction manual.
How to Order Valves
5
Plug-in Manifold Series VQC

C4
C6
C8
CM
L4
L6
L8
B4
B6
B8
LM
With one-touch fitting for ø4
With one-touch fitting for ø6
With one-touch fitting for ø8
Mixed size/with port plug
Elbow top ported with one-
touch fitting for ø4
Elbow top ported with one-
touch fitting for ø6
Elbow top ported with one-
touch fitting for ø8
Elbow bottom ported with
one-touch fitting for ø4
Elbow bottom ported with
one-touch fitting for ø6
Elbow bottom ported with
one-touch fitting for ø8
Mixed size for elbow piping
08
VV5QC 2 1 C6 SDQ
Kit name
(For details on kits, refer to the next page.)
Cylinder port size
SKit
B
2VQC2000
Series
Manifold
1Plug-in manifold
01 1 station
The maximum number of
stations differs depending
on the kits.
Stations
Note 1) Indicate the size in the specification
sheet in the case of “CM” and “LM”.
Note 2) Symbols for inch sizes are as follows:
• N3: ø5/32"
• N7: ø1/4"
• N9: ø5/16"
• NM: Mixed
The top ported elbow is LN쏔and the bottom
ported elbow is BN쏔.
Nil
0
1
8
Number of input blocks
Note) When an AS-i compatible S kit is used, there
is a limit on the maximum number of stations.
For details, please refer to page 13.
Without SI unit
Without input block
With 1-input block
With 8-input block
Nil
1
2
3
Input block type
Without input block
M12 2 inputs
M12 4 inputs
M8 4 inputs
Nil PNP or without input block
NPN
N
Input block COM.
B
D
D쏔
K
N
R
S
T
Nil
Note 1) When two or more options are specified, indicate them
alphabetically.
Example) -BRS
Note 2) When installing a back pressure check valve on the
required station, enter the part number and specify the
station position in the manifold specification sheet.
Note 3) For special DIN rail length, indicate “D쏔”. (Enter the
number of stations inside 쏔.)
Example: -D08
In this case, stations will be mounted on a DIN rail for 8
stations regardless of the actual number of manifold
stations.
The specified number of stations must be larger than the
number of stations on the manifold.
Indicate “D0” for the option without DIN rail.
Note 4) Be sure to indicate the wiring specification in the
specification sheet.
Note 5) For external pilot option, “-R”, indicate the external
pilot specification “R” for the applicable valves as well.
Note 6) The built-in silencer type does not satisfy the IP67
standard.
Note 7) The SUP and EXH ports on U side are branched
(toward the cylinder port and coil) with ø12 one-touch
fittings for connection.
Option
None
With back pressure check valve (all stations) Note 2)
With DIN rail (Rail length: Standard)
With DIN rail (Rail length: Special) Note 3)
Special wiring specification (Except double wiring) Note 4)
With name plate
External pilot Note 5)
Built-in silencer, Direct exhaust Note 6)
P, R port on U side, branched type Note 7)
Note) Without SI unit, the symbol is nil.
Nil
SI unit COM.
+COM.
–COM.
N
SI unit COM.
DeviceNet PROFIBUS-DP CC-Link AS-i CANopen EtherNet/IPControlNet
EX250
Plug-in Manifold
Series VQC2000
Base Mounted
For details about certified products conforming to
international standards, visit us at www.smcworld.com.
How to Order Manifold
... ...
... ...
6

Type of actuation
VQC 2 05
0
Manual override
Nil: Non-locking
push type
(Tool required)
B: Locking type
(Tool required)
C: Locking type
(Manual)
D: Slide locking type
(Manual)
Series
2VQC2000
1
2 position single
2 position double (Metal)
2 position double (Rubber)
3 position closed center
3 position exhaust center
3 position pressure center
1
4 position dual 3 port valve
(A)
4 position dual 3 port valve
(B)
4 position dual 3 port valve
(C)
ANote)
BNote)
CNote)
2
3
4
5
AB
PEBEA
AB
EA P EB
AB
P
EA EB
AB
EBPEA
AB
PEA EB
AB
PEA EB
Note) Rubber seal type only.
1
53
42
N.C N.C
1
53
42
N.O N.O
1
53
42
N.C N.O
Seal
Metal seal
Rubber seal
0
1
Rated voltage
524 VDC
Function
Standard (1 W)
High-pressure type (1.0 MPa)
Negative COM.
External pilot
Low-wattage type (0.5 W)
Nil
KNote 1)
N
RNote 3)
YNote 4)
With/Without light/surge
voltage suppressor
Yes
Nil
Note) There is a limit on the current supplied from an SI unit of the SDTC or SDTD specification to an input block or valve. For details, refer to page 13.
• IP40 for the S kit only, which is compatible with ControlNet. (The other S kits are competible with IP67 ratings.)
SKit
(Serial transmission kit for I/O)
Kit name
IP67
IP40
SI unit: EX250
SI unit
Input block
End plate
SD0
SDQ
SDN
SDV
SDTA
SDTB
SDTC Note)
SDTD Note)
SDY
SDZCN
SDZEN
Without SI unit, Without end plate
DeviceNet
PROFIBUS-DP
CC-Link
AS-i 8in/8out 31Slave Mode, 2 power supply systems
AS-i 4in/4out 31Slave Mode, 2 power supply systems
AS-i 8in/8out 31Slave Mode, 1 power supply system
AS-i 4in/4out 31Slave Mode, 1 power supply system
CANopen
ControlNet (IP40)
EtherNet/IP
1 to 4 stations (8 stations)
1 to 2 stations (4 stations)
1 to 4 stations (8 stations)
1 to 2 stations (4 stations)
1 to 12 stations
(24 stations)
1 to 12 stations
(24 stations)
EX250-SDN1
EX250-SPR1
EX250-SMJ2
EX250-SAS3
EX250-SAS5
EX250-SAS7
EX250-SAS9
EX250-SCA1
EX250-SCN1
EX250-SEN1
—
Symbol Protocol type No. of stations SI unit part no.
How to Order Valves
Note 1) Metal seal type only.
Note 2) When two or more symbols are
specified, indicate them
alphabetically.
Note 3) It is not applicable to dual 3 port
valves.
Note 4) Use a low wattage type for
continuous energization (when
the totaled energized time per
day is longer than the
non-energized time.)
• For solenoid valve specifications and dimensions, refer to the VQC series in the “Best Pneumatics 2004 Vol. 2” catalog.
• For SI unit dimensions, refer to page 12.
• For details on the SI unit, refer to the separate technical instruction manual.
7
Plug-in Manifold Series VQC

SDQ
VV5QC 4 1 16 03 SKit
4VQC4000
Series
Manifold
1Plug-in manifold
Stations
01 1 station
The maximum number of
stations differs depending
on the kits.
Cylinder port size
C8
C10
C12
02
03
B
CM
With one-touch fitting for ø8
With one-touch fitting for ø10
With one-touch fitting for ø12
Rc 1/4
Rc 3/8
Bottom ported Rc 1/4
Mixed size
Option
Nil None
Special wiring specification
(Except double wiring) Note)
K
Note) Be sure to indicate the wiring specification
in the specification sheet.
Nil PNP or without input block
NPN
N
Input block COM.
Nil
1
2
3
Input block type
Without input block
M12 2 inputs
M12 4 inputs
M8 4 inputs
Number of input blocks
Nil
0
1
8
Note) When an AS-i compatible S kit is used, there
is a limit on the maximum number of stations.
For details, please refer to page 13.
Without SI unit
Without input block
With 1-input block
With 8-input block
Nil
SI unit COM.
+COM.
–COM.
N
SI unit COM.
Note) Without SI unit, the symbol is nil.
DeviceNet PROFIBUS-DP CC-Link AS-i CANopen EtherNet/IPControlNet
EX250
Note 1) Indicate the size in the
specification sheet in the
case of “CM”.
Note 2) Symbols for inch sizes
are as follows:
<For one-touch fitting>
• N7: ø1/4"
• N9: ø5/16"
• N11: ø3/8"
• NM: Mixed
Kit name
Note) There is a limit on the current supplied from an SI unit of the SDTC or SDTD specification to an
input block or valve. For details, refer to page 13.
• IP40 for the S kit only, which is compatible with ControlNet. (The other S kits are competible with IP67
ratings.)
SD0
SDQ
SDN
SDV
SDY
SDTA
SDTB
SDTC Note)
SDTD Note)
SDZCN
SDZEN
Without SI unit, Without end plate
DeviceNet
PROFIBUS-DP
CC-Link
CANopen
AS-i 8in/8out 31Slave Mode, 2 power supply systems
AS-i 4in/4out 31Slave Mode, 2 power supply systems
AS-i 8in/8out 31Slave Mode, 1 power supply system
AS-i 4in/4out 31Slave Mode, 1 power supply system
ControlNet (IP40)
EtherNet/IP
EX250-SDN1
EX250-SPR1
EX250-SMJ2
EX250-SCA1
EX250-SAS3
EX250-SAS5
EX250-SAS7
EX250-SAS9
EX250-SCN1
EX250-SEN1
—
Symbol Protocol type No. of stations SI unit part no.
IP67
IP40
SKit
(Serial transmission kit for I/O)
SI unit: EX250
SI unit
Input block
End plate
Plug-in Manifold
Series VQC4000
Base Mounted
For details about certified products conforming to
international standards, visit us at www.smcworld.com.
How to Order Manifold
...
... ...
...
1 to 12 stations
(24 stations)
1 to 12 stations
(24 stations)
1 to 4 stations (8 stations)
1 to 2 stations (4 stations)
1 to 4 stations (8 stations)
1 to 2 stations (4 stations)
8

VQC 4 1 0 5
Manual override
Function
With/Without light/surge
voltage suppressor
Note 1) When two or more symbols are
specified, indicate them
alphabetically.
Note 2) Use a low wattage type for
continuous energization (when
the totaled energized time per
day is longer than the
non-energized time.)
Seal
Metal seal
Rubber seal
0
1
Ye s
Without light, with surge voltage
suppressor
Nil
E
Standard (1 W)
External pilot
Low-wattage type (0.5 W)
Nil
R
YNote 2)
Nil: Non-locking
push type
(Tool required)
B: Locking type
(Tool required)
0
Series
4VQC4000
Rated voltage
524 VDC
Type of actuation
2 position single
2 position double (Metal)
2 position double (Rubber)
3 position closed center
3 position exhaust center
3 position pressure center
3 position double check
1
2
3
4
5
6
AB
PEBEA
AB
EA P EB
AB
P
EA EB
AB
EBPEA
AB
PEA EB
AB
PEA EB
AB
EBPEA
How to Order Valves
• For solenoid valve specifications and dimensions, refer
to the VQC series in the “Best Pneumatics 2004 Vol.
2” catalog.
• For SI unit dimensions, refer to page 12.
• For details on the SI unit, refer to the separate
technical instruction manual.
9
Plug-in Manifold Series VQC

Serial Wiring with Input/Output Unit
Series EX250
Communication protocol
DN1
PR1
MJ2
AS3
AS5
AS7
AS9
CA1
CN1 Note)
EN1
DeviceNet
PROFIBUS-DP
CC-Link
AS-i (8in/8out 31Slave Mode, 2 power supply systems)
AS-i (4in/4out 31Slave Mode, 2 power supply systems)
AS-i (8in/8out 31Slave Mode, 1 power supply system)
AS-i (4in/4out 31Slave Mode, 1 power supply system)
CANopen
ControlNet
EtherNet/IP
DN1EX250 S
How to Order SI Unit
SI Unit
For options, refer to page 16.
Note) The enclosure rating is IP40 for the SI unit compatible with ControlNet.
Input block Output block
Power block
SI unit
Input block
SI unit
Output block
Integrated serial wiring • Ease of mounting, and space-savings are achievable, integrating wiring by connector.
Input/Output number • Compatible with 32-digital outputs/inputs.
Enclosure • IP67 compatible (IP40: compliant with ControlNet)
10