SMC Networks 8504T FICHE User manual

EZ Switch 1000
u4 10/100/1000 RJ-45 Ports
uStore-and-Forward mode with wire-speed filtering 
and forwarding
uAuto MDI/MDIX on 1000BaseT ports
uHalf- and full-duplex flow control 
u"Smart Function" features:
n Console port to manage configuration changes
nPort-based VLAN and L2 Trunking with link
ufail-over
nPriority Queues on each port
Desktop and rack mountable
Plug and play for ease of installation, maintenance and
use
User Guide
SMC8504T
u
u

COPYRIGHT
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC For its use, nor for any infringements of
patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent right of SMC. SMC reserves the
right to change specifications at any time without notice.
Copyright ©2000 by
SMC Network, Inc.
6 Hughes, Irvine, California
all rights reserved. Printed in Taiwan
TRADEMARKS
SMC is a registered trademark; and EZ Switch is a trademark of SMC
Networks, Inc. Other product and company names are trademarks or registered trademarks
of their respective holders.
LIMITED LIFETIME WARRANTY
Limited Warranty Statement: SMC Networks, Inc. ("SMC") warrants its products to be free from
defects in workmanship and materials, under normal use and service, for the applicable warranty
term. All SMC products carry a standard 90-day limited warranty from the date of purchase from
SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product
not operating as warranted with a similar or functionally equivalent product, during the
applicable warranty term. SMC will endeavor to repair or replace any product returned under
warranty within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering
new products within 30 days of purchase from SMC or its Authorized Reseller. Registration can
be accomplished via the enclosed product registration card or online via the SMC web site.
Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty
covers a product during the Life of that Product, which is defined as the period of time during
which the product is an 'Active' SMC product. A product is considered to be ‘Active’ while it is
listed on the current SMC price list. As new technologies emerge, older technologies become
obsolete and SMC will, at its discretion, replace an older product in its product line with one that
incorporates these newer technologies. At that point, the obsolete product is discontinued and is
no longer an 'Active' SMC product. A list of discontinued products with their respective dates of
discontinuance can be found at http://www.smc.com/smc/pages_html/support.html.
All products that are replaced become the property of SMC. Replacement products may be either
new or reconditioned. Any replaced or repaired product carries either a 30-day limited warranty

or the remainder of the initial warranty, whichever is longer. SMC is not responsible for any
custom software or firmware, configuration information, or memory data of Customer contained
in, stored on, or integrated with any products returned to SMC pursuant to any warranty. Products
returned to SMC should have any customer-installed accessory or add-on components, such as
expansion modules, removed prior to returning the product for replacement. SMC is not
responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to returning any
product to SMC. Proof of purchase may be required. Any product returned to SMC without a
valid Return Material Authorization (RMA) number clearly marked on the outside of the package
will be returned to customer at customer’s expense. For warranty claims within North America,
please call our toll-free customer support number at [phone]. Customers are responsible
for all shipping charges from their facility to SMC. SMC is responsible for return shipping
charges from SMC to customer.
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT
OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT
BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS
CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY
OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT,
FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR
FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING
OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR
ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER
PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY
FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO
AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the active SMC
price list. Under the limited lifetime warranty, internal and external power supplies, fans, and
cables are covered by a standard one-year warranty from date of purchase.
COMPLIANCES
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with instructions,
may cause harmful interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
lReorient the receiving antenna
lIncrease the separation between the equipment and receiver
lConnect the equipment into an outlet on a circuit different from
That to which the receiver is connected
lConsult the dealer or an experienced radio/ TV technician for help
EC Conformance Declaration – Class A
European contract: SMC Networks Europe
Edificio Conata II
Calle Fructuós Gelabert 6-8, 2°, 4ª
08970 –Sant Joan Despí
Barcelona, Spain
This information technology product complies with ISO/ IEC Guide 22. It conforms to the
following specifications:
EN55022(1998)/ CISPR-22(1985) Class A
EN50082-1: IEC 1000-4-2, 3,4
This information technology product complies with the requirements of the Low Voltage
Directive 73/ 23/ EEC and the EMC Directive 89/ 336/ EEC and carries the CE Mark
accordingly.

SMC EZ Switch 1000
SMC8504T
The SMC EZ Switch 1000 sets a new standard in entry-level gigabit
switching.
Gigabit Ethernet is the perfect solution to bottlenecks at the core of the
network that are the inevitable result of data-intensive applications and
the proliferation of new users. SMC’s EZ Switch 1000 provides a
seamless migration to higher-speed networking while solving bandwidth
issues.
Network users and applications continue to demand bandwidth intensive
software programs, graphically dense materials and desire faster speeds
to the desktop. SMC EZ Switch 1000 meets that demand with its 4 port
standards-based gigabit switch. This 1U rack mount or desktop switch
seamlessly integrates with the rest of the network through its
auto-negotiating, non-blocking design. With “Smart Features” to
support VLAN, Priority Queing, Trunking and Failover, the SMC8504T
is the most cost effect method for brining speed and service to the
desktop.
Thank you for your purchase and please contact SMC for FREE Service
and Support at 1-800 SMC-4YOU.
Sincerely,
SMC Networks, Inc.

ABOUT THE EZ SWITCH 1000
SMC8504T
The EZ Switch 1000 (SMC8504T) is an 4-port Giga Ethernet Switch. Its 4
10/100/1000BASE-TX ports deliver dedicated 10/100/1000Mbps links to each attached LAN
segment –all with conventional cabling and adapters. Auto-Negotiation is used to select the
optional transmission speed and communication mode for each connection. With
store-and-forward switching and flow control, maximum data integrity is always maintained,
even under heavy loading. Easy installation and reliability make this plug-and-play switch an
ideal choice for smooth Giga Fast Ethernet integration.
Features and Benefits
uFull-duplex on all ports
uANSI/ IEEE802.3/ IEEE802.3u/ IEEE802.3z and IEEE802.3ab compliance ensures
compatibility with standards-based hubs, switches and cards from any vendor
uStore-and-forward switching ensures error-free transmission
uHalf-and full-duplex flow control prevents packets from being dropped under heavy loading
uSmart function:
-support on console port for switch configuration change
-support per port Port-based VLAN and L2 Trunking with link fail-over
-support IEEE802.1p four Priority queues on each port
uPlug and play
uBuilt-in wiring crossovers on all ports allow connections to servers and workstations to be
made with straight-through cabling
u“At-a-glance” LEDs for port and system status monitoring
uDesktop and rack mountable

INSTALLING THE EZ SWITCH 1000
The EZ Switch 1000 can be placed on a desktop or shelf, or installed in a standard 19-in equipment
rack.
Equipment Checklist
After unpacking the EZ Switch 1000, check the contents of the box to be sure you’ve received the
following components:
lEZ Switch 1000 SMC8504T
lAppropriate AC power cable
lRS 232 console port cable
lRack mount bracket set
lSMC Warranty Registration Card
lThis User Guide
Selecting a Site
Be sure to follow the site selection guidelines below when choosing a location:
uSelect a suitable location for the switch:
lIt should be accessible for installing, cabling and maintaining the switch
lThe temperature and humidity should be within the ranges listed in the specifications.
lThe status LEDs should be clearly visible.
lThere should be adequate space (approximately two inches) on all sides for proper air flow.
uBefore rack mounting the switch, pay particular attention to the following factors:
lTemperature: Since the temperature within a rack assembly may be
higher than the ambient room temperature, check that the rack-
environment temperature is within the specified operating temperature
range.
lMechanical Loading: Do not place any equipment on top of a rack-mounted switch.
lCircuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded.
lGrounding: Rack-mounted equipment should be properly grounded. Particular attention
should be given to supply connections other than direct connections to the mains.
uMake sure twisted-pair cable is always routed away from power lines, fluorescent lighting
fixtures and other sources of electrical interference such as radio, transmitters, etc.
uMake sure that a properly grounded power outlet is within 8 feet (2.44 meters) of the switch
and is powered from an independent circuit breaker. As with any equipment, using a filter or
surge suppressor is recommended.
Instructions
1. Positioning the Switch: For desktop or shelf mounting, attach the four adhesive foot pads to
the bottom of the switch. For rack-mounting, attach the mounting brackets to both sides of the
switch with the screws provided, then install the switch in the rack.

2. Applying Power: Plug one end of the power cable into the power receptacle at the back of the
switch, and the other end into an appropriate electrical outlet. Check the Power LED to be sure
it is on.
Note: It is not necessary to power off the switch before connecting or disconnecting any UTP
cables, as these actions will not disrupt the operation of other devices attached to the switch.
3. Connecting PCs: Connect each PC to an RJ-45 port on the switch with a straight-through
twisted-pair cable segment, maximum length 100 meters (328 feet). The EZ Switch 1000 will
support up to 4 PCs.
Note: If an attached device does not support Auto-Negotiation, the data rate will be sensed
automatically and the communication mode will default to half duplex.
4. Cascading Switches and Other Network Devices: If you need more ports, connect the port
with crossover cable on another device. See the “Cable Specifications” and “Connectivity
Guidelines” sections of this guide for further information.
SAMPLE APPLICATIONS
Standalone LAN
High-Speed Switch Links
QoS to ensure important data transmissions like Voice

CONFIGURATION
1. Connect to PC
RS-232 serial cable
Prepare a RS-232 serial cable. Attach the 9-pin female connector to the male connector on the
switch. Plug the other side of this cable to your PC.
2. Hyper Terminal
In Windows 95/98, launch “Hyper Terminal”, create a new connection, and adjust settings as:
l19,200bps
l8 Data bits
lNone Parity
l1 Stop bits
lNone Flow control
Main Menu
Launch the new terminal you just set up, and then, turn on the switch. See the following
message for successful connection:
SMC 8504T (4-port gigabit) [ver: x.xx]
[ 0 ] Speed/ Duplex Setting
[ 1 ] Address Learn
[ 2 ] VLAN
[ 3 ] Queues Priority
[ 4 ] Trunk
[ 5 ] Uplink Port
[ 6 ] Monitor Port
[ 7 ] View Configuration
[ 8 ] Restore To Factory Default
Select: >>
Speed Mode
Input port number for which you want to configure, enter port number and select speed mode
lSpeed/ Duplex Setting
Which port? (1-4, E: Exit, A: Select all ports) …
lPort setting
[ 1 ] Auto-negotiation
[ 2 ] 10 Half Duplex
[ 3 ] 10 Full Duplex
[ 4 ] 100 Half Duplex
[ 5 ] 100 Full Duplex
[ 6 ] 1000 Half Duplex
[ 7 ] 1000 Full Duplex

Select: >> 1
lFlow Control
Enable flow control? (Y/N)
After finish flow control selection
l“Please Wait”
and configure another port or exit
3. Address Learning
Aging Control
A port’s MAC address register is cleared on power-up, or hardware reset. If this item is enabled,
the dynamically learned SA will be learned if it is not refreshed in less than the aging time.
lSelect “1”
Aging Control
[ E ] Enable
[ D ] Disable
Select: >>
lSelect “e”
Max address-aging timer
Max Aging time ( 1 –10 minute) …
4. VLAN Setting
VLAN
Each port of the switch can be assigned to one or multiple VLANs (this device can be divided
into 4 VLANs maximum). Frames from the source port will only be forwarded to destination
ports within the same VLAN domain. A broadcast/ multicast frame will be forwarded to all
ports.
lSelect: >> 2
VLAN Group 1, assigned ports >>
[ S ] Port Select
[ D ] Port Delete
[ A ] Select All ports
[ C ] Save
[ E ] Exit
Select: >>
Queues Priority
The switch can support priority either from tagged frame or based on the input ports. This entry
is for port-based priority, level 0 stand for the lowest priority, level 7 as highest priority. Flow
control will be disable if priority level 7 was selected.
lSelect: >> 3
which port: (1-4, E: Exit) …
5. Trunk Setting
Trunk
This switch can assigned L2 Trunking automatically load-balances among its member ports
through the use of unique and statistical methods, and provides link resiliency (link-fail-over

function) when one or more of the link in a trunk group fails.
lSelect: >> 4
Which Trunk
[ 0 ] Trunk 0 (Disable)
[ 1 ] Trunk 1 (Disable)
[ E ] Exit
Select: >>
Trunk port setting table
Trunk Number Port Number
01~2
13~4
lTrunk 0, member >>
[ A ] ADD
[ D ] Delete
[ C ] Setting
[ E ] Exit
Select: >>
6. Uplink Port Setting
The uplink port provides a way to connect the switch with a repeater hub, a working switch, a
router, or any type of interconnecting device compliance with IEEE802.3 standard for extension
applications.
lSelect: >> 5
Uplink Group 1, assigned ports >>
[ S ] Port Select
[ D ] Port Delete
[ A ] Select All Ports
[ C ] Continue
[ E ] Exit
Select: >>
Note: It is very important that each port is assigned to an uplink port, or data frame might be lost.
The uplink port should be configured to be within the same VLAN as the source port. If the
uplink port is not a member of the VLAN, the broadcast or multi frames will not be forwarded to
its designated uplink port. Multiple VLANs can share the same uplink port.
7. Monitor Port
This feature provides complete network monitoring capability at 100Mbit/s. A copy of egress
(TX) data and ingress (RX) data of the mentioned port is sent to their respective snooping ports.
lSelect:>>6
Monitor Port
[ M ] Monitored Port
[ I ] Monitoring port for Incoming Packets
[ O ] Monitoring Port for Outgoing Packets
[ D ] Disable Port Monitor

[ E ] Exit
Select: >>
8. View Configuration
Display configuration of trunk, uplink and VLAN
lSelect: >>7
[ Current TRUNK ]
Disable
[ Current UpLink ]
Disable
[ Current VLAN ]
Group 1 >> 1234
Press any key to continue..
9. Restore to Factory Default
Select “8” from Main Manu to restore to the default setting as mention before.

EZ SWITCH 1000 SPECIFICATIONS
Model
SMC8504T
Ports
4 RJ-45 ports
10/100Mbps, Twisted-pair, optional straight-through or crossover
1000Mbps, 4 pairs, optional straight-through or crossover
Network Interface
RJ-45: 100ohm, UTP/ STP cable
10/100Base –EIA/ TIA Categories 3 or 5 cable
1000Base –EIA/ TIA Categories 5
LEDs
1000Mbps –one per port
100Mbps –one per port
10Mbps –one per port
FDX/ COL (full duplex/ collision) –one per port
Act (activity) –two per port (TX, RX)
Switching Method
Store –and –forward
MAC Address Table
32K entries
Memory Buffer
8Mbyte per unit
Filtering/ Forwarding/ Learning Rates
Full line rate
Size
12.99 x 8.66 x 1.73 in (33 x 22 x 4.4 cm)
Weight
4.18 lbs (1.9kgs)
Temperature
Operating: 32° to 122℉(0° to 50℃)
Storage: ° to ℉(-20° to 70℃)
Humidity, non-condensing
5% to 90%
Power Requirements
Universal AC input: 100 to 240 VAC, 50 to 60 Hz
Power Consumption
21 Watts maximum
Heat Dissipation
BTU/ hr maximum

Maximum Current
0.2A ﹫110 VAC
0.1A ﹫240 VAC
Standards
ANSI/ IEEE 802.3
ANSI/ IEEE 802.3u
ANSI/ IEEE 802.3ab
ANSI/ IEEE 802.3z
EMC/ Safety Compliances
CE Mark
Emissions
FCC Class A
Safety
CSA/UL (C22.2.950, UL 1950)
Limited Warranty
Lifetime
CABLE SPECIFICATIONS
Cable Type and Connector
10Base-T Cable
Type Length Connector
Category 3, 5 UTP/ STP 100m (328 ft) RJ-45
100Base-TX Cable
Type Length Connector
Category 5 UTP/ STP 100m (328 ft) RJ-45
1000Base-TX Cable
Type Length Connector
Category 5 UTP/ STP 100m (328 ft) RJ-45
RJ-45 Connector Pin Assignment
Caution: DO-NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair
cables with RJ-45 connectors that confirm with FCC standards.
An Ethernet or Fast Ethernet twisted-pair link segment requires two pairs (or 4 pairs for
1000Mbps) of wires. Each wire pair is identified by two (or four) different colors. For example,
one wire might be green and other, green with a white stripe.
Each wire pair must be attached to the RJ-45 connector in a specific orientation. Note how the
pins are numbered in the illustration below. Be sure to hold the connectors in the same orientation
when attaching the wires to the pins.

RJ-45 Pin Assignments
Straight-Through Cable
RJ-45 Pin Assignments
Crossover Cable
End 1 End 2 End 1 End 2
1 (Tx+) 1 (Tx+) 1 (Tx+) 3 (Rx+)
2 (Tx-) 2 (Tx-) 2 (Tx-) 6 (Rx-)
3 (Rx+) 3 (Rx+) 3 (Rx+) 1 (Tx+)
6 (Rx-) 6 (Rx-) 6 (Rx-) 2 (Tx-)
Note: This EZ-8504T can support Auto MDI/ MDI-X.
CONNECTIVITY GUIDELINES
Crossover/ Straight-Through Wiring Requirements
If the port on the
EZ Switch 1000 is…
And the port on the
other device is …
Then use … cable
Crossover (x) Crossover Crossover
Crossover (x) Straight-through Straight-through
Straight-through (=) Crossover Straight-through
Straight-through (=) Straight-through Crossover
Front-Panel LEDs
The front panel of the switch provides a link status LED for each RJ-45 port. In addition, the front
panel also contains status LEDs for “at-a’glance” system monitoring. The following table details
the functions of the various indicators:
Port and Switch Status LEDs
LEDs Condition Status
1000 Mbps Green Indicates that the port is operating at 1000 Mbps
100 Mbps Green Indicates that the port is operating at 100 Mbps
10 Mbps Green Indicates that the port is operating at 10 Mbps
Green Indicates that the port is operating in full-duplex
mode
Fdx/ Col
Flashing Green Indicates a collision occurred on the port segment
when operating in half-duplex mode.
Act
(TX, RX)
Green Indicate that the connection between port and
attached device is valid.
Front-Panel Ports
The front-panel ports are multi-speed RJ-45 ports with built-in wiring crossovers. PCs can be
connected to these ports with straight-through or crossover cable. Each port supports
Auto-Negotiation, so the optimum communication mode (half or full duplex) and data rate (10 Mbps,
100 Mbps or 1000 Mbps) are selected automatically.

Rear Panel
The AC power receptacle is located on the rear panel of the switch
Console RS-232
19200,N,8,1
100-240VAC 50-60Hz

TROUBLESHOOTING
1. Symptom
Power LED does not light after power on.
Probable Causes
Power outlet or power cord may be defective.
Possible Solutions
lCheck for loose connections
lCheck the power outlet by using it for another device.
lReplace the power cord.
2. Symptom
Link LED does not light after connection is made.
Probable Causes
Switch port, network card or cable may be defective.
Possible Solutions
lCheck that the switch and attached device are both powered on.
lBe sure the network able is connected to both devices
lVerify that Category 5 cable is used for 100Mbp connections and that the length of any
cable does not exceed 100 meters (328 feet).
lCheck the network card and cable connections for defects.
lReplace the defective card or cable if necessary.

6 Hughes
Irvine, CA 92618
Phone: [phone]
FOR TECHNICAL SUPPORT, CALL:
From U.S.A. and Canada (24 hours, 7 days a week)
(800) SMC-4-YOU; [phone]; [phone] (Fax)
From Europe (8:00 AM - 5:30 PM UK Greenwich Mean Time)
44 (0) 1188 748740; 44 (0) 1189 748741 (Fax)
INTERNET
E-mail address:
[email protected]
european.techs[email protected]
Driver updates:
http://www.smc.com/support.html
World Wide Web:
http://www.smc.com/
FTP Site:
ftp.smc.com
FOR LITERATURE OR ADVERTISING RESPONSE, CALL:
U.S.A. and Canada: (800) SMC-4-YOU; Fax [phone]
Spain: 34-93-477-4920; Fax [phone]
UK: 44 (0) 1188 748700; Fax [phone]
Southern Europe: 33 (1) 41.18.68.68; Fax [phone]
Central/Eastern Europe: 49 (0) 89 92861-200; Fax [phone]
Nordic: 46 (8) 564 33145; Fax [phone]
Middle East: 971-48818410; Fax [phone]
South Africa: 27 (0) 11-3936491; Fax [phone]
PRC: 86-10-6235-4958; Fax [phone]
Taiwan: 886-2-2747-4780; Fax [phone]
Asia Pacific: (65) 238 6556; Fax [phone]
Korea: 82-2-553-0860; Fax [phone]
Japan: 81-45-224-2332; Fax [phone]
Australia: 61-2-9416-0437; Fax [phone]
India: 91-22-8204437; Fax [phone]
Model Number: SMC8041TX
Publication Number: 150709-102 E062001-R01
SMC8041TX_.book Page 12 Thursday, June 7, 2001 3:33 PM