SMC Networks PF2W7 Series User manual

No.PF※※-OMO0012-D
PRODUCT NAME
Digital Flow Switch
(Integrated display type)
MODEL / Series / Product Number
PF2W7##

-1-
No.PF※※-OMO0012-D
Table of Contents
Safety Instructions 2
Model Indication and How to Order 10
Summary of Product parts 12
Definition and terminology 13
Mounting and Installation 15
Installation 15
Piping 16
Wiring 18
Outline of setting 20
List of outputs 21
Initialize mode 22
Setting procedure of initialize mode 23
Function selection mode 26
F_1 Input procedure of the Set value of instantaneous output 27
F_2 Input procedure of the Set value of instantaneous output (Auto-preset) 28
F_3 Input procedure of the Set value of accumulated output 29
Key-lock function 31
Maintenance 32
Troubleshooting 33
Cross-reference for troubleshooting 33
Error indication 35
Specification 36
Specifications 36
Characteristics data 38
Dimensions 39
Made to Order 45

-2-
No.PF※※-OMO0012-D
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or
"Danger".
They are all important notes for safety and must be followed in addition to International Standards
(ISO/IEC)*1), and other safety regulations.
*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.
ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines. (Part 1: General requirements)
ISO 10218: Manipulating industrial robots -Safety.
etc.
Caution
Caution indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.
Warning
Warning indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.
Danger
Danger indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications
based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the
person who has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when
configuring the equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/equipment until safety is
confirmed.
1. The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are
implemented and the power from any appropriate source is cut, and read and understand the specific
product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation andmalfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the
product is to be used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place
exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3. An application which could have negative effects on people, property, or animals requiring special
safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using
a mechanical protective function, and periodical checks to confirm proper operation.

-3-
No.PF※※-OMO0012-D
Safety Instructions
Caution
1.The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance
Requirements".
Read and accept them before using the product.
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after the product is
delivered, whichever is first.2)
Also, the product may have specified durability, running distance or replacement parts.
Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our
responsibility, a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other
damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and
disclaimers noted in the specified catalog for the particular products.
2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the
vacuum pad or failure due to the deterioration of rubber material are not covered
by the limited warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of
mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed
by the relevant security laws and regulation of the countries involved in the transaction.
Prior to the shipment of a SMC product to another country, assure that all local rules
governing that export are known and followed.
Caution
SMC products are not intended for use as instruments for legal metrology.
Products that SMC manufactures or sells are not measurement instruments that are qualified by pattern
approval tests relating to the measurement laws of each country.
Therefore, SMC products cannot be used for business or certification ordained by the measurement laws of
each country.

-4-
No.PF※※-OMO0012-D
Operator
This operation manual is intended for those who have knowledge of machinery using pneumatic
equipment, and have sufficient knowledge of assembly, operation and maintenance of such
equipment. Only those persons are allowed to perform assembly, operation and maintenance.
Read and understand this operation manual carefully before assembling, operating or providing
maintenance to the product.
■Safety Instructions
Warning
■Do not disassemble, modify (including changing the printed circuit board) or repair.
An injury or failure can result.
■Do not operate the product outside of the specifications.
Do not use for flammable or harmful fluids.
Fire, malfunction, or damage to the product can result.
Verify the specifications before use.
■Do not operate in an atmosphere containing flammable, explosive or corrosive gas.
Fire or an explosion can result.
This product is not designed to be explosion proof.
■Do not use the product for flammable or highly permeable fluids.
A fire or explosion can result.
■Do not use the product in a place where static electricity is a problem.
Otherwise it can cause failure or malfunction of the system.
■If using the product in an interlocking circuit:
Provide a double interlocking system, for example a mechanical system
Check the product regularly for proper operation
Otherwise malfunction can result, causing an accident.
■The following instructions must be followed during maintenance:
Turn off the power supply
Ensure the flow is shut off before performing maintenance
Otherwise an injury can result.

-5-
No.PF※※-OMO0012-D
Caution
■Do not touch the terminals and connectors while the power is on.
Otherwise electric shock, malfunction or damage to the product can result.
■Do not touch the piping or its connected parts when the fluid is at high temperature.
It may lead to burnt.
Ensure the piping cools sufficiently before touching.
■After maintenance is complete, perform appropriate functional inspections and leak tests.
Stop operation if the equipment does not function properly or there is a leakage of fluid.
When leakage occurs from parts other than the piping, the product might be faulty.
Disconnect the power supply and stop the fluid supply.
Do not apply fluid under leaking conditions.
Safety cannot be assured in the case of unexpected malfunction.
■NOTE
○Follow the instructions given below when designing, selecting and handling the product.
●The instructions on design and selection (installation, wiring, environment, adjustment, operation,
maintenance, etc.) described below must also be followed.
Product specifications
Use the specified voltage.
Otherwise failure or malfunction can result.
Insufficient supply voltage may not drive a load due to a voltage drop inside the product.
Verify the operating voltage of the load before use.
Do not exceed the specified maximum allowable load.
Otherwise it can cause damage or shorten the lifetime of the product.
Data stored by the product is not deleted, even if the power supply is cut off.
(writing time: 1000000 cycles.)
The applicable fluids are that the product for water is applicable for 0 to 50 oC and the product for high
temperature fluid is applicable for 0 to 90 oC and ethylene glycol 50% solution (0 to 90 oC) with viscosity
of 3 mPa●s (3 cP) or less.
Measurement accuracy is not guaranteed if other fluids are used.
Do not use fluids containing chemicals, synthetic oils, organic solvents, salt or corrosive gases.
Using such fluids can result in malfunction and damage to the product.
Check the details of the specifications before use.
Before designing piping confirm the pressure loss at the sensor from the pressure loss graph.
Confirm pressure loss of the sensor from the characteristics data.
Consider measures to prevent over pressure due to water hammer.
<Measures to reduce water hammer>
1. Install a water hammer relieving valve.
2. Use a flexible material for piping (such as a rubber hose) and an accumulator that can absorb impact pressure.
3. Keep piping as short as possible.
Use the specified measurement flow rate and operating pressure.
Otherwise it can cause damage to the product or inability to measure correctly.
Reserve a space for maintenance.
Allow sufficient space for maintenance when designing the system.

-6-
No.PF※※-OMO0012-D
●Product handling
Installation
Tighten to the specified tightening torque.
If the tightening torque is exceeded the mounting screws and brackets may damaged.
If the tightening torque is insufficient, the product may be displaced and the mounting screws may come loose.
(Refer to page 15 "Mounting and Installation".)
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode
power supply.
Do not drop, hit or apply excessive shock to the product.
Otherwise damage to the internal parts can result, causing malfunction.
Do not pull the lead wire forcefully, or lift the product by the lead wire. (Tensile force 49 N or less)
Hold the product body when handling, to prevent damage, failure or malfunction.
The tensile strength of the power supply/output connection cable is 50 N and the sensor lead wire with a
connector is 25 N.
For piping of the product, hold the piping with a spanner on the metal part of the product (Piping
attachment).
Holding other parts with a spanner leads to may damage the product.
Any dust left in the piping should be flushed out by air blow before connecting the piping to the product.
Otherwise damage or malfunction can result.
Refer to the flow direction of the fluid indicated on the product label for installation and piping.
Do not mount the body with the bottom facing upwards.
Avoid piping in which the piping size of the IN side of the product changes suddenly.
If the piping size is reduced sharply or there is a restrictor such as a valve on the IN side, fluid velocity distribution
in the piping will be disturbed, leading to improper measurement.
Therefore, the above-mentioned piping should be connected on the OUT side.
If the OUT side is opened, or flow rate is excessive, cavitations may be generated, which may result in improper
measurement.
As a measure against this, it is possible to reduce the cavitations by increasing the fluid pressure.
Take action such as mounting an orifice on the OUT side of the product, and confirm that there is no malfunction
before handling.
If the orifice of the OUT side is fully closed to operate the pump, the switch may malfunction due to the effect of
pulsation (pressure fluctuation). Ensure that there is no malfunction before usage.
Do not insert metal wires or other foreign matter into the piping port.
It can damage the sensor causing failure or malfunction.
Never mount a product in a location that will be used as a foothold.
The product may be damaged if excessive force is applied by stepping or climbing onto it.
If there is a risk of foreign matter entering the fluid, install and pipe a filter to the inlet.
The adherence of foreign matter to the vortex generator or detector can cause errors in measurement accuracy.
A filter of approx. 40 mesh is recommended.
Design and install the application so that the fluid detection path is always full.
If the product is mounted vertically, let the liquid flow from bottom to top.
Trapped air bubbles can cause errors in measurement accuracy.
(If the fluid detection path is always filled with liquid, there will be no problem.)
Do not apply excessive rotational force to the monitor.
Rotating the monitor with excessive force will damage the end stop.

-7-
No.PF※※-OMO0012-D
Wiring
Do not pull the lead wires.
In particular, never lift a product equipped with fitting and piping by holding the lead wires.
Otherwise damage to the internal parts can result, causing malfunction or disconnection of the connector.
Avoid repeatedly bending or stretching the lead wire, or placing heavy loads on it.
Repeated bending stress or tensile stress can cause damage to the sheath, or breakage of the wires.
If the lead wire can move, fix it near the body of the product.
The recommended bend radius of the lead wire is 6 times the outside diameter of the sheath, or 33 times the
outside diameter of the wire insulation material, whichever is larger.
Replace any damaged lead wire with a new one.
Wire correctly.
Incorrect wiring can damage the product.
Do not perform wiring while the power is on.
Otherwise damage to the internal parts can result, causing malfunction.
Do not route wires and cables together with power or high voltage cables.
Otherwise the product can malfunction due to interference or noise and surge voltage from power and high voltage
cables.
Confirm proper insulation of wiring.
Poor insulation (interference from another circuit, poor insulation between terminals, etc.) can lead to excess
voltage or current being applied to the product, causing damage.
Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage.
Do not use a cable longer than 30 m.
Wire the DC(-) line (blue) as close as possible to the power supply.
When analogue output is used, install a noise filter (line noise filter, ferrite element, etc.) between the
switch-mode power supply and this product.

-8-
No.PF※※-OMO0012-D
Environment
Do not use the product in an environment that is constantly exposed to the splash of water.
Otherwise failure or malfunction can result. Take measures such as using a cover.
Do not use the product in an environment where corrosive gases or fluids could be splashed.
Otherwise damage to the product and malfunction can result.
Do not use in a place where the product could be splashed by oil or chemicals.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent,
even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires).
Do not use in an area where electrical surges are generated.
If there is equipment generates a large electrical surge (solenoid type lifter, high frequency induction furnace, motor,
etc.) close to the product, damage or failure of the internal circuit may occur. Take measures against the surge
sources, and prevent the wires from coming into close contact.
Do not use a load which generates surge voltage.
When a surge-generating load such as a relay or solenoid is driven directly, use a product with a built-in surge
absorbing element.
The product is CE marked, but not immune to lightning strikes. Take measures against lightning strikes
in the system.
Do not use the product in areas that are exposed to vibration or impact.
Otherwise failure or malfunction can result.
Do not use the product in the presence of a magnetic field.
This may lead to the malfunction of the product.
Prevent foreign matter such as wire debris from entering the product.
Otherwise failure or malfunction can result.
Do not use the product in areas subject to large temperature cycle.
Heating/cooling cycles other than ordinary changes in temperature can adversely affect the internal structure of the
product.
Do not expose the product to direct sunlight.
If using in a location directly exposed to sunlight, use a suitable protective cover.
Otherwise failure or malfunction can result.
Keep within the operating fluid temperature and operation temperatures range.
The operating fluid temperature range is 0 to 50 oC and the product for high temperature fluid is 0 to 90 oC, and
operating temperature range is 0 to 50 oC.
If the fluid freezes, it may cause damage and malfunction of the product, so please take measures to prevent
freezing.
When a fluid at a lower temperature than the ambient temperature is supplied, the product can break due to
condensation and malfunction. Keep the product from having condensation.
Please be aware that water droplets may cause early deterioration/damage, particularly if the product is installed
vertically or upside-down.
Protection against freezing is necessary.
Avoid sudden temperature change even within specified temperature. Otherwise failure or malfunction can result.
Do not operate close to a heat source, or in a location exposed to radiant heat.
Otherwise malfunction can result.

-9-
No.PF※※-OMO0012-D
Adjustment and Operation
Connect load before turning on the power.
Do not short-circuit the load.
Although an error is displayed when the product load is short circuited, excess current may cause damage to the
product.
Do not press the setting buttons with a sharp pointed object.
This may damage the setting buttons.
Supply the power when there is no flow.
If using the product to detect very small flow rates, warm up the product for 10 to 15 minutes first.
There will be a drift on the display or the analogue output of approximate 2 to 3% immediately after the power
supply is turn on, within 10 minutes.
Check regulators and flow adjustment valves before introducing the fluid.
If pressure or flow rate beyond the specified range are applied to the sensor, the sensor unit may be damaged.
Do not attempt to insert or pull the flow rate sensor or its connector when the power is on.
The output is off for 3 seconds after power is supplied.
Use settings suitable for the operating conditions.
Incorrect settings can cause operational failure.
(Refer to page 20 "Outline of setting")
During the initial setting and any subsequent flow rate setting, the product will switch the output
according to the existing settings until the changes are complete.
Confirm the output has no adverse effect on machinery and equipment before setting.
Stop the control system before setting if necessary.
The product is a flow meter using Karman vortex. The flow meter using Karman vortex has lower output
frequency at excess flow state. Do not use the product within the excess flow area in the chart below.
Maintenance
Perform regular maintenance and inspections.
There is a risk of unexpected malfunction of components due to the malfunction of equipment and machinery.
Turn off the power supply, stop the fluid and check the safety before performing any maintenance.
There is a risk of unexpected malfunction.
Do not use solvents such as benzene, thinner etc. to clean the product.
They could damage the surface of the body and erase the markings on the body.
Use a soft cloth to remove stains.
For heavy stains, use a cloth lightly dampened with diluted neutral detergent, then wipe up any residue with a dry
cloth.

-10-
No.PF※※-OMO0012-D
Model indication and How to Order

-11-
No.PF※※-OMO0012-D
Lead wire
NIL
N
with lead wire and connector
(Straight, 3 m)
without lead wire
: Lead wire is not assembled with the product, but shipped together.
Made to order
Model indication
Content
Page
PF2W7--28--X560
Output specification: NPN (1 output) + Analogue (1 to 5 V)
Page 45
PF2W7--29--X560
Output specification: NPN (1 output) + Analogue (4 to 20 mA)
PF2W7--68--X560
Output specification: PNP (1 output) + Analogue (1 to 5 V)
PF2W7--69--X560
Output specification: PNP (1 output) + Analogue (4 to 20 mA)
Accessories/Part number
If an accessory is required separately, order using the following part numbers.
Part number
Description
Remarks
ZS-37-A
Lead wire with connector (Straight)
Length: 3 m
ZS-37-B
Lead wire with connector (Right angle)
Length: 3 m
ZS-29-T
Bracket (PF2W704/720)
Mounting screw (3 x 12 Self tapping screw)
4 pcs.
ZS-29-V
Bracket (PF2W740/7T)
Mounting screw (3 x 12 Self tapping screw)
4 pcs.
ZS-29-W
Bracket (PF2W711)
Mounting screw (3 x 12 Self tapping screw)
4 pcs.

-12-
No.PF※※-OMO0012-D
Summary of Product parts
Body
Connector pin
numbers
(On the product)
1
DC(+)
2
OUT2
3
DC(-)
4
OUT1
Item
Description
Monitor part
See below.
Piping port
Connected to the fluid inlet at IN side and to the fluid outlet at OUT side.
Body
The body of the product.
Bracket
Bracket for mounting the product.
Connector
Connector for electrical connections.
Lead wire and connector
Lead wire to supply power and transmit output signals.
Monitor part
Item
Description
LED display
Displays the flow value, setting mode, and error indication.
Indicator LED (OUT1)
Indicates the output status of OUT1. LED is ON (Green) when OUT1 is ON.
The LED flashes when an over current error occurs.
When the accumulated pulse output mode is selected, the indicator LED will turn OFF.
Indicator LED (OUT2)
Indicates the output status of OUT2. LED is ON (Red) when OUT2 is ON.
The LED flashes when an over current error occurs.
When the accumulated pulse output mode is selected, the indicator LED will turn OFF.
button (UP)
Selects the mode or increases the ON/OFF Set value.
button (SET)
Press this button to change to another mode and to set a value.
button (DOWN)
Selects the mode or decreases the ON/OFF Set value.

-13-
No.PF※※-OMO0012-D
■Definition and terminology
Terms
Meaning
A
Accumulated flow
The total amount of fluid that has passed through the device. If an instantaneous flow of
10 L/min continues for 5 minutes, the accumulated flow will be 10 x 5 = 50 L.
Accumulated pulse
output
A type of output where a pulse is generated every time a predefined accumulated flow
passes. It is possible to calculate the total accumulated flow by counting the pulses.
Analogue output
Outputs a value proportional to the flow rate. When the analogue output is in the range
1 to 5 V, it will vary between 1 to 5 V according to the rate of flow. The same for
analogue output of 4 to 20 mA.
Attachment
A metal part at both sides of the product to connect piping.
Auto-preset
This function calculates and sets the pressure values automatically based on the
on-going operation.
C
Cavitation
A phenomenon that may occur in a fluid moving at high speed. In the parts of the fluid
where the pressure is low, vapour bubbles form and then rapidly collapse. If cavitation
is present for a prolonged period, exposed surfaces will be damaged; this is called
cavitation damage or erosion.
Chattering
The problem of the switch output turning ON and OFF repeatedly around the Set value
at high frequency due to the effect of pulsation.
D
Digit
Minimum unit for setting/display is 1 digit. When the minimum unit for setting/display is
5 L/min, 3 digits will be 3 x 5 = 15 L/min
Display flow range
The range which can be displayed by the product with a digital display.
F
Fluid temperature
Range of fluid temperature that can be measured by the product.
F.S.
(Full span, Full scale)
Stands for "full span" or "full scale", and indicates varied analogue output range at rated
value. For example, when analogue output is 1 to 5 V, F.S. = 5[V] - 1[V] = 4[V], (ref.
1%F.S. = 4[V] x 1% = 0.04[V])
H
Hysteresis
The difference between ON and OFF points used to prevent chattering. Hysteresis can
be effective in avoiding the effects of pulsation.
Hysteresis mode
Mode where the switch output will turn ON when the flow is greater than the Set value,
and will turn OFF when the flow falls below the Set value by the amount of hysteresis or
more.
I
Instantaneous flow
The volume of flow per unit of time. If it is 10 L/min, there is a flow of 10 L passing
through the device in 1 minute.
Internal voltage drop
The voltage drop across the product (and therefore not applied to the load), when the
switch output is ON. The voltage drop will vary with load current, and ideally should be
0 V.
K
Karman vortex
When an object is placed in a fluid stream, a vortex will be created in the fluid on the
downstream side. This vortex is called a Karman vortex. The frequency at which the
vortices are generated is proportional to the fluid velocity, therefore it is possible to
calculate the fluid flow rate by measuring the Karman vortex frequency.
M
Minimum
setting/display unit
The resolution of set and display values.
If the minimum setting unit is 1 L/min, the flow can be displayed in 1 L/min units, i.e. 10,
11, 12.
O
Operating humidity
range
The ambient humidity range within which the product will meet all published
specifications.
Operating
temperature range
The ambient temperature range within which the product will meet all published
specifications.

-14-
No.PF※※-OMO0012-D
Terms
Meaning
P
Part in contact with
fluid
A part that comes into physical contact with the fluid.
Pressure
characteristics
The amount of variation in the analogue output or display value when the supply
pressure is changed.
Proof pressure
The pressure beyond which the flow switch will be damaged.
R
Rated flow range
The flow range within which the product will meet all published specifications.
Rated pressure range
The pressure range within which the product will meet all published specifications.
Repeatability
Reproducibility of the display or analogue output value, when the flow is repeatedly
changing.
Response time
Time from when the target flow is applied until the flow reaches 90% of the Set value.
S
Setting flow range
The range of ON/OFF threshold values that can be set for flow switches products with a
switch output.
Switch output
An output type that has only 2 conditions, ON or OFF. In the ON condition an indicator
LED will turn on, and any connected load will be powered. In the OFF condition, there
will be no indicator LED and no power is supplied to the load.
T
Temperature
characteristics
The amount of variation in the analogue output or display value when the ambient
temperature is changed.
U
Unit selection function
Function to change the unit in which the value of flow is displayed. Only a product with
this function can change the unit. A product with unit selection function cannot be
purchased if it is used within Japan. Flow is indicated only by SI units in Japan.
W
Water hammer
A momentary steep pressure increase due the spread of pressure by closing a
contactor such as a valve for an extremely short time while there is a flow.
This pressure increase is known as water hammer or impact pressure.
Window comparator
mode
An operating mode in which the switch output is turned on or off depending on whether
the flow is within the range of 2 Set values.

-15-
No.PF※※-OMO0012-D
Mounting and Installation
■Installation
Never mount the product in a location that will be used as a foothold.
The rotation angle of the monitor is 270o, in steps of 90o. Rotating the display part with excessive force will
damage the end stop.
●Installing
Install the product (with bracket) using the M4 screws (4 pcs.) supplied.
Bracket thickness is approximately 1.6 mm (approximately 2 mm for PF2W711).
Refer to the dimension drawing of the bracket (page 44) for mounting hole dimensions.

-16-
No.PF※※-OMO0012-D
■Piping
Use the product within the specified operating pressure range and temperature range.
Proof pressure is 1.5 MPa.
Connect the piping to the fittings.
Mount the product so that the fluid direction is the same as the arrow indicated on the product.
Never mount the product upside down.
The piping on the IN side must have a straight section of piping whose length is 8 times the piping
diameter or more.
Avoid piping in which the piping size on the IN side of the product changes suddenly.
Bubbles may be generated depending on the piping design. Refer to an example of recommended piping
system.
(If the fluid detection path is always filled with liquid, there will be no problem.)

-17-
No.PF※※-OMO0012-D
●Connecting the piping
Ensure that the metal piping attachments are tightened to the required torque (refer to the table below).
If the tightening torque is exceeded, the product can be broken. If the tightening torque is insufficient, the
fittings may become loose.
When connecting piping to the product, a spanner should be used on the metal piping attachment only.
Using a spanner on other parts may damage the product.
Avoid any sealing tape from entering inside the piping.
Ensure that there is no leakage from loose piping.
Nominal thread size
Required torque
Rc(NPT)3/8
22 to 24 Nm
Rc(NPT)1/2
28 to 30 Nm
Rc(NPT)3/4
28 to 30 Nm
Rc(NPT)1
36 to 38 Nm
Model
Width across flats of
attachment
PF2W704
34 mm
PF2W720
PF2W740
PF2W711
45 mm
PF2W704T
34 mm
PF2W720T
PF2W740T

-18-
No.PF※※-OMO0012-D
■Wiring
Connections should only be made with the power supply turned off.
Use separate routes for the product wiring and any power or high voltage wiring. Otherwise, malfunction
may result due to noise.
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode
power supply. When a switch-mode power supply is connected to the product, switching noise will be
superimposed and the product specification can no longer be met. This can be prevented by inserting a
noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the
product, or by using a series power supply instead of a switch-mode power supply.
●Connecting the wiring
Align the lead wire connector with the connector key groove, and insert vertically.
Connection is complete when the knurled part is fully tightened. Check that the connection is not loose.
●Connector Pin numbers
When the lead wire with connector designated for the PF2W7 is used, the wire colours will apply as shown
in the diagram.
Connector Pin numbers (on the lead wire)
Pin number
Content
Colour
1
DC(+)
Brown
2
OUT2
White
3
DC(-)
Blue
4
OUT1
Black

-19-
No.PF※※-OMO0012-D
●Internal circuit and wiring example
When the lead wire with connector designated for the PF2W7 is used, the wire colours will apply as shown
in the diagram.
NPN (2 outputs) type
PF2W7--27-
Max. 30 V, 80 mA
Internal voltage drop: 1 V or less
PNP (2 outputs) type
PF2W7--67-
Max. 80 mA
Internal voltage drop: 1.5 V or less